Contact Us

TPS7A9101DSKR

Brand: Texas Instruments
Texas Instruments TPS7A9101DSKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A9101DSKR — Power Management & Signal Chain | Superb Automation

TPS7A9101DSKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A9101DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A9101DSKR: 1 A, 0.8 V to 5.2 V adjustable low noise LDO in a 10 pin SON body

TPS7A9101DSKR is a 1 A adjustable low dropout regulator built for analogue and RF rails where output noise and rejection matter more than the last few millivolts of dropout in a SON body of 10 pins. It sources 1 A with 200 mV of maximum dropout, holds 1 per cent accuracy over line, load and temperature, and quotes 4.7 uVRMS of output noise from 10 Hz to 100 kHz. The adjustable window runs from 0.8 V to 5.2 V from a 1.4 V to 6.5 V input, and the DSK body is 10 pins with a power good output and an active discharge on the output.

Order code and package

TPS7A9101DSKR10 pin SON (DSK), 3000 pieces on a large reel, marking 19GP, moisture level 2 with a one year floor life
TPS7A9101DSKTsame body and silicon, 250 pieces on a small reel, the prototype quantity
Feedback voltage0.8 V reference, so the output is set by the divider and not by an internal tap
Power goodopen drain, needs a pull up between 10 kOhm and 100 kOhm to a rail no higher than the output
Operating temperatureminus 40 C to plus 125 C junction, all rows carry the same grade

Electrical parameters that decide the application

Input voltage1.4 V to 6.5 V operating, the same range applies to the enable pin
Output voltage0.8 V to 5.2 V adjustable, set by the external divider on the feedback pin
Output current1 A maximum continuous
Dropout voltage200 mV maximum at 1 A, and the front page quotes 100 mV of maximum dropout for the lighter load condition
Output accuracy1 per cent over line, load and temperature, with the divider tolerance excluded
Output noise4.7 uVRMS from 10 Hz to 100 kHz, quoted with the noise reduction arrangement on the control pin
Rejection40 dB at 1 MHz, with the low frequency figure far higher, which is the point of the part
Current limit1.5 A minimum and 1.7 A typical, foldback rather than a hard clamp
Undervoltage lockout1.31 V minimum and 1.39 V maximum rising, with 290 mV of hysteresis on the way down
Active discharge250 ohm switch on the output when the enable pin is low

What the control pins actually do

SS_CTRL pinsets the start up ramp with a capacitor, and also serves as the noise reduction point, so one pin does two jobs that are normally separate
PG pinopen drain indicator, useful for sequencing a second rail without an external supervisor
Foldback current limitthe limit falls as the output voltage falls, so a shorted rail dissipates far less than 1.5 A times the input voltage would suggest
Active discharge250 ohm to ground when disabled, which guarantees the rail is at zero before a re enable
Thermal shutdown160 C junction, non latching
Body and pin count10 pin SON at 3 mm by 3 mm, sized for the 1 A dissipation rather than for a small outline

Points to check before this part goes on a BOM

Noise is quoted at a stated bandwidth and with a stated output capacitor, and both have to match the application before the number means anything. The 4.7 uVRMS figure belongs to 10 Hz to 100 kHz with the control pin capacitor fitted. Remove that capacitor and the low frequency noise rises by a factor that shows up immediately on a spectrum analyser, which is why the vendor puts the noise reduction function on the same pin as the soft start.

The 1 per cent accuracy figure excludes the divider. That is normal for an adjustable regulator, but it means a 1 per cent part with 1 per cent resistors is a 2 per cent rail unless the divider is trimmed or the resistors are 0.1 per cent. On a 3.3 V rail that is 66 mV of spread, which is enough to matter for a rail feeding an ADC reference or an RF amplifier bias.

Dropout of 200 mV maximum at 1 A is the headline, and the front page also quotes 100 mV of maximum dropout for a lighter load. The two are consistent once the load is named, but the difference matters for a 5 V rail running from a 5.5 V supply, where 1 A is not available at all. At 0.5 A the part is comfortably in regulation and at 1 A it is not, and the vendor curve rather than the front page is the thing to read.

The current limit is a foldback, which is the reason a 1 A regulator can survive a short on a 6.5 V input. Foldback also means the part will not start into a load that draws more than the foldback knee, so a board with a large capacitive load and a low resistance path can latch off at start up even though it would run fine once charged. The soft start capacitor is the tool that fixes it.

The power good output is open drain and needs a pull up between 10 kOhm and 100 kOhm to a rail no higher than the output voltage. Tying it to a 5 V rail on a 1.2 V output violates that and reverse biases the pin, which is a common mistake when a supervisor on the same board is powered from the higher rail. If the pull up has to go to another rail, an external transistor is cheaper than a replacement board.

The 250 ohm active discharge is fast enough to bring a 10 uF output to zero in a few milliseconds and slow enough not to stress the pass transistor. On a rail that is re enabled quickly, the discharge also means the next start up begins from zero rather than from a residual voltage, which is what makes the monotonic start behaviour repeatable in a test fixture.

Undervoltage lockout at 1.39 V maximum rising is well below the 1.4 V bottom of the operating range, so there is essentially no margin. A 1.5 V input feeding a 0.8 V output is in specification, but a 1.45 V input is inside the lockout window on a slow ramp. Rails below 1.5 V in should be checked against the lockout curve rather than the operating range on the front page.

Where this order code fits

It feeds RF amplifier bias rails, ADC and DAC supplies, low jitter clock generators and analogue front ends in instrumentation, where a switching regulator upstream has already done the efficient step down and the last stage has to remove its ripple. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the RF Component Sourcing page.

Questions buyers ask

Is 1 A available at any output voltage? No. The 1 A rating holds while the input is at least the output plus dropout. At 5 V out, 1 A needs 5.2 V in plus margin, so a 5.5 V supply is at the edge and the vendor curve shows where the part leaves regulation.

How is the output voltage set? By a divider on the feedback pin against a 0.8 V reference. The divider tolerance is not part of the 1 per cent accuracy figure, so use 0.1 per cent resistors on a precision rail.

What bandwidth does the noise figure use? 10 Hz to 100 kHz, with the noise reduction capacitor on the control pin fitted. Outside that bandwidth the number does not apply.

Can the power good pin pull up to 5 V on a 1.2 V rail? No. The pull up has to go to a rail no higher than the output, between 10 kOhm and 100 kOhm. A higher rail reverse biases the pin.

What happens on a shorted output? The foldback limit reduces the current as the output falls, and the part recovers when the short is removed. It does not latch.

Does it need an output capacitor for stability? Yes, a ceramic output capacitor is required, and the value in the vendor table is the minimum for stability rather than a recommendation. Larger capacitance lowers noise and improves the load transient.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.