Contact Us

TPS7A8400RGRR

Brand: Texas Instruments
Texas Instruments TPS7A8400RGRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A8400RGRR — Power Management & Signal Chain | Superb Automation

TPS7A8400RGRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A8400RGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A8400RGRR: 3 A low noise LDO, 0.8 V to 5 V, 180 mV dropout, ANY-OUT pins, VQFN-20

TPS7A8400RGRR is a 3 A low noise linear regulator with a pin programmable output bank, so the rail can be set to one of a set of voltages without a divider and adjusted further with one if needed in a VQFN-20 body of 20 pins. Dropout is 180 mV maximum at 3 A, accuracy is one per cent over line, load and temperature, and output noise is 4.4 microvolt rms at 0.8 V and 7.7 microvolt rms at 5 V. The ANY-OUT pins set the output in steps from 0.8 V to 3.95 V with no external resistors, and an external divider extends the range to 5.0 V. A bias rail from 1.1 V allows operation with the input only slightly above the output.

Order code and package

TPS7A8400RGRRActive, VQFN (RGR) body, 20 pins, 3000 pieces on a 330 mm reel, marking 11CI
TPS7A8400RGRR.AActive, same body and same 3000 piece reel, material row at MSL Level-1-260C-UNLIM
TPS7A8400RGRTActive, the same part with 250 pieces on a small reel
Temperature rangeminus 40 to 125 degrees junction
Output settingANY-OUT pins for 0.8 V to 3.95 V, or an external divider for up to 5.0 V

Electrical parameters that decide the application

Input voltage1.4 V to 6.5 V without bias, 1.1 V to 6.5 V with a bias rail
Output voltage0.8 V to 3.95 V from the ANY-OUT pins, 0.8 V to 5.0 V with a divider
Output current3 A maximum
Dropout180 mV maximum at 3 A
Accuracyone per cent over line, load and temperature
Noise and rejection4.4 microvolt rms at 0.8 V, 7.7 microvolt rms at 5 V, 40 dB rejection at 500 kHz
Quiescent currentin the low milliamp range, higher without the bias rail
Soft start and power goodexternal capacitor sets the ramp, open drain power good output

Family variants and how they differ

TPS7A84003 A member, the string on this page
TPS7A8401the same family with a different output setting arrangement
TPS7A522 A member with the same noise and rejection in a 12 pin body
ANY-OUT pinseach pin adds a fixed increment to the output, so the voltage is set by which pins are grounded
Body optionsRGR with standard flanks, and other bodies in the same family for a smaller footprint

Points to check before this part goes on a BOM

ANY-OUT pins remove the divider current and the divider error at the same time. A conventional 3 A regulator uses a divider that draws tens of microamps and contributes its own tolerance to the output. Setting the voltage by grounding pins on the part removes both, which is why the accuracy figure can be quoted at one per cent over the full range rather than at 25 degrees only. The trade is that only the preset values are available without a divider.

One hundred and eighty millivolts at 3 A is 540 milliwatts of dissipation with a 0.18 V drop. That is the best case. A 1.2 V output from a 1.5 V input at 3 A dissipates 0.9 W, and the 20 pin body needs the exposed pad soldered to a copper area with vias. A rail that runs close to dropout at full current is a thermal problem before it is an electrical one.

The bias rail is what makes the low dropout possible. With a bias at least 1.5 V above the output the pass element is driven from that rail and the input can sit only 180 mV above the output. Without it the input floor is 1.4 V and the dropout is larger. A board that has a 3.3 V rail available can use it as the bias for a 1.2 V output and get the full 180 mV figure.

Noise of 4.4 microvolts is a measurement condition as much as a specification. It applies with the recommended output capacitor and the noise reduction capacitor fitted, in the 10 Hz to 100 kHz band. Removing the noise capacitor raises the low frequency noise well above the figure, and a board that leaves that pin open will not measure what the data sheet promises. On a rail feeding an ADC the difference is visible in the noise floor.

Rejection of 40 dB at 500 kHz is the number that matters behind a switcher. A buck running at 500 kHz puts its ripple at that frequency and its harmonics, and 40 dB takes 100 mV down to 1 mV. At lower frequencies the rejection is much higher, so the part cleans a switching supply well and does not clean a low frequency disturbance nearly as effectively.

Three amps in a linear regulator is a heater with a regulator attached. At 3 A and a 0.5 V drop the part dissipates 1.5 W, which is more than most of the converters on the same board. The part is used where the noise matters more than the efficiency, usually on an analogue rail that draws a few hundred milliamps, and the 3 A rating is there for headroom rather than for continuous operation at the limit.

The power good output and the soft start capacitor are not optional in a sequenced system. Power good is open drain and has to be pulled up to a rail that is alive before this regulator. The soft start capacitor sets how fast the output rises, and a 3 A regulator with a large output bank and no soft start capacitor draws the full current limit at power up.

A 20 pin body with an exposed pad is the only way to get the thermal path. The pad is connected to ground and to the thermal plane, and the vias under it are part of the electrical return as well as the heat path. A board that connects the pad with a single via gets a regulator that works at low current and folds back at high current, which looks like a current limit problem rather than a thermal one.

What to confirm before this part goes on a purchase order

State the output voltage and whether it is one of the preset values. If it is not, a divider is needed and the accuracy figure changes.

Give the input rail, the output current and the bias arrangement. The 180 mV dropout only holds with a bias rail, and the dissipation at full current decides the package.

Where this order code fits

It holds a 0.8 V to 5 V analogue rail at 3 A in test equipment, a medical front end or a communications card, where noise on the rail would appear in the signal. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it be set to 3.3 V without a divider? Yes, if 3.3 V is one of the values the ANY-OUT pin combination produces. The pins add fixed increments to a base voltage, so a specific combination gives 3.3 V with no external resistors. A value between the increments needs a divider and loses the divider free accuracy.

Does it need a bias supply? For the 180 mV dropout figure, yes. The bias rail drives the pass element, so the input can sit only slightly above the output. Without it the input must be at least 1.4 V and the dropout is larger, which changes the headroom calculation on a tight rail.

Why would a 3 A regulator be used on a 300 mA load? Because the load current is not the reason for the part. The noise, the rejection and the accuracy are, and the extra current capability gives thermal and transient headroom. The dissipation at 300 mA is a fraction of the full load figure, so the thermal problem disappears.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.