Contact Us

TPS7A4700RGWR

Brand: Texas Instruments
Texas Instruments TPS7A4700RGWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A4700RGWR — Power Management & Signal Chain | Superb Automation

TPS7A4700RGWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A4700RGWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A4700RGWR: 36 V, 1 A, 4 microvolt noise RF regulator with pin programmed output

TPS7A4700RGWR is a 36 V input, 1 A low dropout regulator built for analogue rails where supply noise sets the system floor in a VQFN (RGW) body of 20 pins. The output is programmed from 1.4 V to 20.5 V by connecting or leaving open a set of pins, so there are no feedback resistors and no feed forward capacitor, and the noise is 4 microvolts RMS from 10 Hz to 100 kHz.

Order code and package

Order code read outTPS7A4700 RGW R: family, RGW 20 pin VQFN 5 mm by 5 mm, R large tape and reel
PackageVQFN (RGW), 20 pins, 5.00 mm by 5.00 mm, thermal pad, 1 mm class height
Carrier3000 pieces on a large reel per the addendum
Operating temperatureminus 40 to plus 125 degrees Celsius
Finish and moistureNIPDAU lead finish, MSL level 2, 260 degrees peak reflow, one year floor life
MarkingPXSQ
SiblingsTPS7A4701 adds a resistor adjustable mode for outputs up to 34 V in the same body

Electrical parameters that decide the application

Input voltage3 V to 36 V, the rail that makes this part useful after a 24 V or 28 V bus
Output voltage, TPS7A47001.4 V to 20.5 V, set by the pin strapping, no external divider
Output current1 A
Dropout307 mV typical and 450 mV maximum at 1 A
Output noise4 microvolts RMS from 10 Hz to 100 kHz
Ripple rejection82 dB at 100 Hz, 55 dB across 10 Hz to 10 MHz
EnableCMOS logic level compatible, so it can be tied to a 1.8 V or 3.3 V control pin
Protectionfixed current limit and thermal shutdown, both internal
Output capacitorceramic stable, the value follows the load transient requirement rather than a minimum ESR rule
Thermal padthe underside pad is the only heat path, and the 5 mm body relies on it at 1 A
Start upthe enable pin ramps the output in a controlled way, and the reference is filtered on chip to keep the ramp monotonic

Family variants and how they differ

TPS7A4700the ANY-OUT version, output set by pins, ceiling 20.5 V
TPS7A4701the same silicon with an additional adjustable mode that reaches 34 V using external resistors
Why it mattersa 24 V rail cannot be produced by the 4700 at all, and the 4701 is the part that can
Noise claimthe 4 microvolt figure belongs to the family at a stated output and bandwidth, and it moves with the output voltage
Negative railsthis family is positive only, a negative analogue rail needs a separate device

Points to check before this part goes on a BOM

The output voltage is a board feature, not a component value. ANY-OUT programming connects pins to ground or leaves them open, and the sum of the connected weights sets the output. That removes the divider error and the feed forward capacitor, and it also means that changing the rail voltage means changing the board. A build that needs 5.0 V and 5.2 V versions needs two board variants, not two resistor reels.

The 20.5 V ceiling is a hard stop. Above that the part cannot regulate at all, and a 24 V industrial rail needs the TPS7A4701 with its resistor mode. Quoting the 4700 into a 24 V application is a mistake that only shows up at first power up, because the pin strapping simply stops short of the target.

1 A in a 5 mm body is a thermal statement. At 307 mV of dropout and 1 A the part dissipates 0.31 W, which the package handles. At 12 V in and 5 V out the same 1 A is 7 W, which it does not, and the thermal shutdown will cycle. The part is a post regulator after a switcher, and the input to output differential belongs in the specification before the current does.

Noise and rejection are quoted at particular outputs. The 4 microvolt RMS figure and the 82 dB rejection at 100 Hz are measured at a stated output voltage and load, and the rejection falls as the output approaches the input, because the pass element runs out of gain. A 20 V output from a 21 V input has almost no rejection left, however good the number looks on the front page.

The enable pin is CMOS level and that is not the same as 5 V tolerant. It is meant to be driven from the logic rail of the system, and pulling it to a 5 V source when the part is off can forward bias protection structures. Sequence the enable from a 3.3 V or 1.8 V domain, or use a divider.

The output capacitor sets the transient, and the part does not need a minimum ESR. A 10 microfarad ceramic at the load covers most steps, and the 1 A load transient produces a dip that follows the capacitor rather than the loop, because the loop is deliberately slow to keep the noise down. That trade is the core of the part: quiet, but not fast.

The pin programming is a grid, not a continuum. Each strap contributes a fixed weight, so the output lands on steps rather than anywhere between 1.4 V and 20.5 V. The common analogue rails, 3.3 V, 5 V, 12 V and 15 V, all have a setting, and an odd value such as 6.2 V may not. Checking the grid before the board is released avoids discovering that the required rail is between two steps.

A 1 A regulator in a 5 mm body needs the pad soldered to copper. The junction to ambient path goes through the thermal pad and the vias under it, and a pad connected to a thin trace rather than a plane raises the junction by tens of degrees. At 0.31 W of dissipation the part is comfortable; at 2 W it is not, and the difference is the copper rather than the current.

Where this order code fits

These parts clean up the supply for RF amplifiers, phase locked loops, analogue to digital converters and precision references in test equipment, radar front ends and medical instruments, where a 24 V bus has to become a quiet 5 V or 12 V rail. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can I get 24 V out of the TPS7A4700? No. The pin programmed ceiling is 20.5 V. The TPS7A4701 in the same body reaches 34 V with an external divider, and that is the part for a 24 V rail.

Why does the output voltage change when I fit a different board revision? Because the voltage is set by which pins are grounded on that revision. Compare the pin strapping between the two boards before assuming a component fault.

Is 4 microvolts RMS realistic on my board? It is the regulator contribution under the stated test conditions. Board noise, the reference bypass and the load transient response usually set the measured floor, so the part is a starting point rather than the whole answer.

Is a negative rail available in this family? No. This family is positive only. A negative analogue rail needs a separate negative regulator, and the two are usually paired around an amplifier stage.

What is the difference between the 4700 and the 4701? The 4701 adds a resistor adjustable mode that reaches 34 V. The 4700 stops at 20.5 V in pin mode, which is enough for a 15 V rail and not enough for a 24 V one.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop RF Supply page sets out the checks that keep a substitute from failing on the bench.