Contact Us

TPS7A2433DBVR

Brand: Texas Instruments
Texas Instruments TPS7A2433DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2433DBVR — Power Management & Signal Chain | Superb Automation

TPS7A2433DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2433DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2433DBVR: 200 mA, 18 V, 2 microamp LDO, 3.3 V fixed output

TPS7A2433DBVR is a fixed 3.3 V linear regulator rated 200 mA with a 2 microamp quiescent current in a SOT-23 body of 5 pins. It takes up to 18 V at the input and still draws 2 microamp, which is the combination that makes it usable on a 12 V or 15 V rail that has to stay alive between measurement cycles. Dropout is 250 mV maximum at full current, so a 3.6 V input is enough to hold a 3.3 V rail.

Order code and package

TPS7A2433DBVRActive, SOT-23-5, 3000 pieces on a large reel, NIPDAU or SN finish
TPS7A2401DBVRActive, the adjustable member, 1.24 V to 17.75 V through a divider
Fixed options1.25 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 3.6 V and 5.0 V in the same body
MSLLevel-1-260C-UNLIM, so no floor life limit at 30 degrees and 60 per cent humidity
Temperature rangeminus 40 to 125 degrees on every row

Electrical parameters that decide the application

Input voltage2.4 V to 18 V
Output3.3 V fixed, 200 mA
Quiescent current2.0 microamp
Dropout250 mV maximum at 200 mA
Accuracy1.25 per cent over temperature
Efficiency example92.8 per cent from 3.55 V in to 3.3 V out at full load
Output capacitorstable with 1 microfarad
Protectionovercurrent, thermal shutdown, active overshoot pulldown

Family variants and how they differ

Fixed versionno feedback resistors, two fewer parts and no divider error, this order code
Adjustable versionTPS7A2401DBVR, 1.24 V to 17.75 V, needs the divider
TPS7A26the 500 mA sibling at 590 mV dropout with a power good output
Overshoot pulldownan active circuit pulls the output down when the input collapses
BodySOT-23-5, 2.9 mm by 1.6 mm

Points to check before this part goes on a BOM

2 microamp at 18 V input is the headline. A conventional regulator on a 15 V rail would burn tens of microamp just holding itself up, which on a battery backed instrument is the difference between a year and five. The figure is quoted at light load, and the note to read is that it rises with load, so it is a sleep current rather than a running current.

250 mV dropout at 200 mA is tight for a high voltage part. It means a 3.6 V rail holds 3.3 V at full load with 50 mV to spare. On a 3.4 V input the rail will follow the input down. Boards that need 3.3 V from a 3.3 V bus have to look at a different part, because this one is built for a wide input with a comfortable step down.

The active overshoot pulldown is a protection most regulators do not have. When the input collapses quickly the output can be left sitting above the input with charge stored in the output capacitor. The pulldown discharges it, which protects a processor from a reverse biased rail. On a board that loses power randomly, this is the difference between a clean reset and a latch up.

The 92.8 per cent efficiency figure needs its conditions. It is quoted from 3.55 V to 3.3 V, which is the best case, because the drop across the pass element is only 250 mV. From 12 V the same part dissipates 1.74 W at full load and efficiency falls below 40 per cent. The number is real and it does not apply to the 12 V case.

1.25 per cent is a regulator figure, not a reference figure. For 3.3 V that is about 41 mV over temperature. It is fine for a logic rail, for a sensor supply and for a comparator threshold that is derived from the same rail. It is not fine as an ADC reference, where the ratio to the measured signal is what matters.

The fixed version removes two resistors and one error term. A divider adds its own tolerance and its own temperature coefficient on top of the regulator, and it draws current from the output. On a 2 microamp part a divider in the tens of microamp would defeat the whole purpose, which is why the fixed version is the right choice for a 3.3 V rail.

18 V input with 125 degree junction is the industrial envelope. That covers 12 V and 15 V rails with margin and 24 V rails only if the input is clamped. The part is not a 36 V or 40 V device. A 24 V rail with a 10 per cent transient already sits above 18 V, so a different regulator is needed there.

Level-1 moisture sensitivity matters for a assembly house. Unlimited floor life at 30 degrees and 60 per cent humidity means the reel can stay open on the line. Combined with 3000 pieces on a large reel, this is a part that suits a normal surface mount line without a bake step, which is not true for every LDO in this class.

The 3.6 V code is one of the slower ones. The family covers 1.25 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 3.6 V and 5.0 V, and the wide spaced voltages move faster than the odd ones. A 3.6 V requirement, common where a 3.3 V load sits at the end of a long cable, is one of the slow ones. Ordering it early, or taking the adjustable member with a divider, is usually cheaper than a broker premium once the shortage shows up.

Two rails from one bus should not share a divider. On the adjustable member the divider draws its current from the output continuously, and on a part chosen for 2 microamp of quiescent current a divider in the tens of microamp defeats the reason for the part. Where several 3.3 V rails are needed from one bus, use the fixed version on each rail and let each regulator stand on its own, rather than one adjustable regulator feeding a chain of dividers.

Where the 18 V input pays for itself

Industrial sensors and meters powered from a 12 V or 15 V loop that must keep a microcontroller alive while the main load is off.

Battery backed equipment where the same rail has to survive a charging voltage well above the nominal battery voltage without a second regulator in front.

Where this order code fits

It holds a 3.3 V rail on a 12 V or 15 V industrial bus and keeps a microcontroller and its sensor alive between measurement cycles, in meters, detectors and cordless tools. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can it run from 5 V and deliver 3.3 V at 200 mA continuously? Yes. The dissipation is 340 mW and the SOT-23-5 can carry it on a reasonable copper area at normal ambient. Above about 60 degrees ambient the number has to be checked against the thermal table rather than assumed.

Is the adjustable version a drop in for the fixed one? Same body and same pin count, but the feedback pin has to be connected to a divider instead of the output. It is a board change, so it is not a purchasing substitution even though the package matches.

What protects the rail if the input is removed quickly? The active overshoot pulldown discharges the output capacitor when the input collapses, which keeps the output from sitting above the input. It does not replace a reverse blocking diode where the load can back feed the rail.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.