Contact Us

TPS7A0228PDQNR

Brand: Texas Instruments
Texas Instruments TPS7A0228PDQNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0228PDQNR — Power Management & Signal Chain | Superb Automation

TPS7A0228PDQNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0228PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0228PDQNR: a 2.8 V, 200 mA nanopower LDO in a 1 mm X2SON

TPS7A0228PDQNR is a 1.5 V to 6.0 V fixed output low dropout regulator in a X2SON (DQN) body of 4 pins. The code breaks down as the TPS7A02 family, a 2.8 V fixed output, the P grade, and the DQN body, which is 1.00 mm by 1.00 mm with four pins on a 3000 piece reel. The 2.8 V setting is fixed inside the part, so nothing on the board adjusts it and the ordering string is the only place the voltage is visible.

Order code and package

TPS7A0228PDQNRX2SON (DQN), 4 pins, 3000 piece large reel, -40 to 125 C, 2.8 V fixed output
TPS7A0228PDBVRSOT-23 (DBV), 5 pins, 3000 piece large reel, same 2.8 V setting
TPS7A0228PYCHRDSBGA (YCH), 4 pins, 12000 piece large reel, 0.64 mm square body
TPS7A0210PDQNRsame X2SON body at 1.0 V, for the low core rails
Finish and floor lifeNIPDAU lead finish, MSL level 1 at 260 C, unlimited floor life out of the bag
Output steps across the family0.8 V to 5.0 V in 50 mV steps, so a rail within one step of 2.8 V exists rather than needing a divider

Electrical parameters that decide the application

Input and output1.5 V to 6.0 V in, 0.8 V to 5.0 V out, 6.5 V absolute maximum on VIN, VEN and VOUT
Current200 mA continuous, with an output current limit of 450 mA typical spanning 240 mA to 750 mA and a short circuit limit of 65 mA
Quiescent current25 nA typical and 46 nA maximum at 25 C, held at the same 25 nA even when the part is in dropout
Shutdown current3 nA typical and 10 nA maximum with VEN at 0 V
Accuracy1 percent at 25 C, 1.5 percent over the full -40 to 125 C range
Dropout270 mV maximum at 200 mA for a 3.3 V to 5.0 V setting, rising to 1050 mV maximum for a 0.8 V to 1.0 V setting
Transient responsesettling under 10 microseconds for a 1 mA to 50 mA step, with 100 mV of undershoot
Enablesmart enable pulldown holds the regulator off with the EN pin floating and limits the current drawn through an external pulldown when it is on
Stabilitystable with a 1 uF or larger output capacitor, ceramic included
Line and load regulation20 mV line regulation over the input window, 20 mV typical load regulation from 1 mA to 200 mA
Thermal-40 C to 125 C junction, with the output current folded back rather than the part shutting down on a sustained overload

Family variants and how they differ

TPS7A0210PDQNRsame 200 mA, same body, 1.0 V output for a processor core rail
TPS7A0212PDBVR1.2 V in the SOT-23 body, for boards that cannot place a 1 mm part
TPS7A0215DQNR1.5 V, the setting that sits closest to the 1.5 V input floor
Body options1.00 mm X2SON, 0.64 mm DSBGA or SOT-23, all with the same 25 nA quiescent current
Against the TPS7A02 adjustable ideathere is no adjustable member of this family, the voltage is set by the ordering string and the 50 mV step grid is what gives the choice

Points to check before this part goes on a BOM

The 25 nA quiescent current is the entire reason this part exists, and it holds in dropout as well as in regulation. A regulator that draws microamps when the battery is already below the set point will flatten a coin cell during storage, and the TPS7A02 keeps the same 25 nA figure in that state, with 3 nA in shutdown. For a device that spends most of its life asleep, those two numbers decide the shelf life more than any other specification on the page.

Dropout is quoted per output band and the spread is wide. A 3.3 V setting needs 270 mV maximum at 200 mA, but a 1.0 V setting needs 1050 mV, so the same part asked for a low output from a 2 V input is closer to its floor than the headline number suggests. The 2.8 V ordering string sits in the 2.5 V to 3.3 V band, which is the 450 mV maximum column, and that is the figure to use when the input comes from a lithium cell that is nearly empty.

The smart enable pulldown is a small feature with a real board consequence. With the EN pin left floating the regulator stays off, so a board without an external pull down does not leak through the enable path during assembly test. It also limits the current drawn through an external pulldown when the pin is driven high, which is why a 1 MOhm resistor is enough where other regulators need 100 kOhm.

The four pin X2SON has no ground or enable flexibility: VIN, VOUT, EN and GND, with the fixed output inside. Any change to the rail voltage is a change of ordering string, not a change of resistor, so a BOM that mixes two voltage codes in one bin produces boards that measure correctly at test and fail in the field at the wrong voltage.

Where a 200 mA nanopower regulator fits

Wearables, thermostats, smoke and heat detectors, gas and water meters, blood glucose monitors and pulse oximeters share one property: the load is a few milliamps for a second and microamps for hours. A regulator with a microamp quiescent current would dominate the average draw in that duty cycle, which is why the 25 nA figure matters more than the 200 mA ceiling.

The transient behaviour is quoted for a 1 mA to 50 mA step with under 10 microseconds of settling, which is what a radio waking up looks like. A part chosen only on quiescent current and unspecified transient response will brown out the MCU on every transmit burst, so both numbers belong on the selection sheet.

The tolerance over temperature is 1.5 percent, which is generous for a part whose value is fixed inside the package. On a 2.8 V rail that is plus or minus 42 mV from -40 to 125 C, comfortably inside the window a 3.0 V sensor or a 2.5 V logic rail needs, and it means the regulator does not need a calibration step at test.

Where this order code fits

It powers sensor nodes, meters, wearables and any battery product where the sleep current decides how long the cell lasts. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the 2.8 V output adjustable on the board? No. The voltage is fixed inside the part and encoded in the ordering string, so 2.8 V comes from the 28 in TPS7A0228PDQNR and a different rail needs a different code from the same 50 mV grid. There is no feedback divider to change.

Can the X2SON body be replaced with the SOT-23? Electrically yes, TPS7A0228PDBVR is the same 2.8 V part in a five pin SOT-23. On the board it is a different footprint and a different reel count, so the substitution is a footprint change rather than a drop in replacement.

What is dropout at 200 mA? 270 mV maximum for a 3.3 V to 5.0 V setting, 450 mV for the 2.5 V to 3.3 V band that the 2.8 V part sits in, and 1050 mV at the bottom of the range. The figure has to be read against the output voltage, not taken as a single number.

How does it behave in shutdown? 3 nA typical and 10 nA maximum with EN at 0 V. Combined with the smart pulldown that keeps the part off when the pin floats, a board in storage does not drain the cell through the regulator.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.