Contact Us

TPS79918DRVR

Brand: Texas Instruments
Texas Instruments TPS79918DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS79918DRVR — Power Management & Signal Chain | Superb Automation

TPS79918DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS79918DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS79918DRVR: 1.8 V, 200 mA, 40 uA quiescent, in a six pin WSON

The TPS79918DRVR is the 1.8 V fixed member of the TPS799 family from Texas Instruments, a 200 mA regulator with 40 microamps of quiescent current, 70 dB of rejection at 100 Hz, and a noise floor of 18.9 microvolts RMS at 1.8 V with a 0.01 uF capacitor on the noise reduction pin. It comes in the six pin WSON body coded DRV, 3000 pieces per reel, nickel palladium gold finish, moisture level 1, marking AWV.

This order code carries a footnote that a buyer should read before writing a specification. The dropout table is not measured for outputs below 2.8 V, because the minimum input of 2.7 V is reached before the pass device saturates at 200 mA. So the governing number for a 1.8 V rail is the input floor of 2.7 V plus the load regulation, not the 100 mV dropout row that belongs to the 3.3 V point. A 3.3 V bus with 10 percent tolerance sits at 2.97 V and is inside the rating, but a 2.5 V bus cannot supply this part at all.

Key electrical data for the 1.8 V point

Output voltage1.8 V fixed, plus or minus 1 percent at 25 C and 2 percent over the full range
Output current200 mA continuous, current limit 220 mA to 600 mA
Input range2.7 V to 6.5 V, the 2.7 V floor governs this voltage
Quiescent current40 uA typical and 60 uA maximum from 500 uA to 200 mA
Noise18.9 uV RMS at 1.8 V with a 0.01 uF capacitor, 169 uV RMS with no capacitor
Rejection70 dB at 100 Hz, 66 dB at 1 kHz, 51 dB at 10 kHz, 38 dB at 100 kHz

Package, marking and reel data

BodyWSON DRV, 6 pins, 2.0 mm by 2.0 mm, exposed pad
Reel3000 pieces, large tape and reel
Finish and moistureNIPDAU, level 1, unlimited floor life
MarkingAWV
Thermal resistance74.2 C per W junction to ambient in the six pin WSON

Where a quiet 1.8 V rail at 200 mA is used

The TPS799 family is written for portable radio and instrument supplies where the quiescent current has to stay low and the noise has to stay lower. A 1.8 V rail at 200 mA covers a radio baseband, an audio codec, a low power FPGA bank or a sensor hub, and the 40 uA quiescent current is the figure that decides battery life when the load is in microamps most of the time. At 1 mA of load the part draws 40 uA, which is 4 percent of the load, so a 1.8 V always on rail is practical on a coin cell only if the duty cycle is low.

The noise behaviour depends on the capacitor on the noise reduction pin. With 0.01 uF the part reaches 18.9 microvolts at 1.8 V, and without any capacitor the figure is 169 microvolts, which is a factor of nine. The pin is optional for stability and mandatory for the noise number, and a bill of material that omits it gets a different regulator than the one in the data sheet. The start up time also depends on the same capacitor, 45 to 50 microseconds across the range, which is short enough that a sequencer rarely has to wait for this rail.

Thermally the WSON body is the best of the three in this family at 74.2 C per W, against 143.3 in the DSBGA and 225.3 in the SOT-23-THIN. At 200 mA from 3.3 V to 1.8 V the dissipation is 0.3 W and the rise is 22 degrees, so the body is not the limit. From 5 V the same current is 0.64 W and a 48 degree rise, which is still inside the 125 degree junction rating but leaves less margin in a sealed enclosure.

Buyer questions on this order code

Why is there no dropout figure for 1.8 V? Because the input floor of 2.7 V is reached first. The dropout rows in the table cover outputs of 2.8 V and above, and for a 1.8 V rail the specified minimum input is the number that limits the supply, not the pass device.

Is the six pin WSON the same part as the five pin SOT-23-THIN? The die and the trim are the same family, but the body, the thermal resistance and the marking differ, and the SOT-23-THIN body is 225.3 C per W against 74.2 here. A substitution between them changes the thermal budget on the board even when the electrical table matches.

Does the noise reduction pin need a capacitor? For the published noise figure, yes. 0.01 uF gives 18.9 microvolts at 1.8 V and no capacitor gives 169 microvolts. The part is stable either way, so the decision is about noise rather than about stability.

Sourcing the TPS79918DRVR through SUPERB

SUPERB quotes this part with the body and the marking stated, because the family is offered in three bodies with very different thermal resistances under one electrical table. The AWV marking, the level 1 moisture class and the date code are verified on receipt, and the certificate of conformance travels with the reel.

Where the rail has to be quieter than this part allows, the power management cross reference page lists the alternatives we can compare on noise and quiescent current, and RF component sourcing covers the radio side of the same bill. Send the load profile and the rail and the answer follows.