Contact Us

TPS79318DBVR

Brand: Texas Instruments
Texas Instruments TPS79318DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS79318DBVR — Power Management & Signal Chain | Superb Automation

TPS79318DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS79318DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS79318DBVR: 200 mA low noise regulator for 1.8 V analog and RF loads

TPS79318DBVR is a low dropout linear regulator with an enable pin in a SOT-23 body of 5 pins. The fixed 1.8 V member of a family that trades dropout against noise for sensitive analog loads. It is stable with a 2.2 uF ceramic output capacitor, quotes 112 mV of dropout at 200 mA, and comes in a five pin SOT-23 that most boards already have room for.

Order code and package

TPS79318DBVRactive, production, SOT-23 5 pins, 3000 pieces on a large reel
TPS79318DBVRG4green row, same body and reel
TPS79318DBVRM3same die on the same 3000 piece reel, added suffix row
MarkingPHHI on the five pin body
Moisture levelLevel 1, 260 C, unlimited floor life
Temperatureminus 40 to 125 C

Electrical parameters that decide the application

Input voltage2.7 V to 5.5 V for the 1.8 V fixed member
Output current200 mA
Output voltage1.8 V fixed, adjustable member covers 1.22 V to 5.5 V
Dropout112 mV typical and 200 mV maximum at 200 mA on the current chip
Output noise55 uV RMS on the legacy chip, 69 uV RMS on the current chip
Start up50 us on the legacy chip, 500 us on the current chip
Lockout2.25 V to 2.65 V rising on the legacy chip
Current limitabout 400 mA with foldback on the legacy chip
Output capacitor2.2 uF ceramic, stable from 1 uF upward
Shutdownenable pin, verified by the output discharge

Family variants and how they differ

Legacy chipfixed 1.8 V to 4.75 V, 55 uV noise, 50 us start up, DSBGA body available
Current chipfixed 1.8 V to 3.3 V, 69 uV noise, 500 us start up, SOT-23 only
TPS79301adjustable member with a 1.22 V reference and a feedback pin
TPS79325 and TPS793282.5 V and 2.8 V fixed members of the same family
TPS7A20the vendor points to this part as the newer replacement family
Enableactive high, the part draws no current when held low

Points to check before this part goes on a BOM

Two silicon generations share one part number. The legacy chip is quieter at 55 uV and starts in 50 us, the current chip is 69 uV and 500 us, and nothing on the reel label separates them except the marking. A build that qualified on the older noise figure has to re-measure when the newer chip arrives.

Dropout is not specified for the 1.8 V and 2.5 V members, because the minimum input of 2.7 V leaves 900 mV of headroom at 1.8 V out and the part never operates near dropout. Quoting a 112 mV dropout on a 1.8 V rail is technically true of the family and meaningless for this order code.

The 200 mA rating is also a thermal statement in a five pin SOT-23. At 5 V in and 1.8 V out the part dissipates 640 mW at full load, and the package cannot hold that without a copper area far larger than the body. In practice the rail has to come from a lower input or carry less current.

Current limit on the legacy chip folds back from about 400 mA. A load that draws 300 mA at start up, such as a large ceramic bank, pulls the output down until the foldback settles, and the rail comes up slowly rather than limiting at a fixed current.

The enable pin is not a soft start. Asserting it starts the output in 50 us on the legacy chip, and the inrush into the output capacitor comes straight from the input rail. A 10 uF output capacitor and a 50 us rise is 200 mA of inrush, which is the whole rating before the load draws anything.

Noise of 55 uV or 69 uV is quoted over a 10 Hz to 100 kHz band with a noise reduction capacitor on the NR pin where the body provides one. Leaving that pin open raises the figure and moves the spectrum, which is why the same part measures differently on two boards.

The vendor names the TPS7A20 as the newer family for this slot. That matters at the end of a build: the TPS793 is still active, but a long life product should carry the replacement in its approved list before the last time buy question comes up.

Where it still makes sense

A 1.8 V rail at 50 to 100 mA feeding a low noise amplifier, a clock buffer or an ADC reference divider is the case this part was built for. At those currents the dissipation is under 300 mW in the SOT-23 and the noise is the binding specification rather than the dropout.

For a 1.8 V rail at 200 mA the arithmetic does not work in the five pin body. The same family in a larger package, or a switching regulator followed by a small filter, is the honest answer.

Reading the two chip generations from a datasheet

The revision history is the only place the split is stated plainly. Where a table gives two columns for noise, start up or the fixed voltage range, the left column is the legacy chip and the right is the current one, and the note under the table says which order codes still ship the older die.

Incoming inspection can separate them by marking. That is worth doing before a production run rather than after, because the two chips differ in start up time by a factor of ten and a power sequencing chain built around the faster one will see the slower one arrive late.

What a substitute has to match

Three figures decide whether a second source works in this socket: the output noise over the 10 Hz to 100 kHz band, the start up time, and the dropout at the rated current. A part that matches the current and the package but starts in 500 us instead of 50 us will break a sequencing chain built around the faster chip.

The pinout matters as much as the numbers. The five pin SOT-23 puts IN, GND, EN, NC or NR and OUT in a fixed order, and several regulators that look equivalent on paper swap the enable and the noise pin, which turns a drop in replacement into a board spin.

Where this order code fits

The order code turns up in analog front ends, RF boards and instrument rails where a quiet 1.8 V supply matters more than efficiency. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is a 1 uF output capacitor enough? The part is stable from 1 uF upward with a ceramic dielectric, and the vendor curves are drawn at 2.2 uF. Below 1 uF the phase margin falls and the transient response shows it.

What is the difference between the DBVR and DBVT suffixes? Reel size. Both are the same five pin SOT-23 body, one on a 3000 piece reel and the other on a 250 piece reel for prototype quantities.

Can the enable pin be tied to the input? Yes, and that is the normal connection when the rail has no sequencing requirement. The pin draws almost no current and has no upper limit below the input voltage.

Why does the datasheet quote two noise figures? Because two silicon generations share the part number. The lower figure belongs to the legacy chip and the higher one to the current chip.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.