TPS79101DBVR
Product Specifications
TPS79101DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79101DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79101DBVR: an adjustable 100 mA low noise low dropout regulator in a six pin SOT-23 with a 1.2246 V reference
TPS79101DBVR is a BiCMOS linear regulator with 70 dB of supply rejection at 10 kHz, 38 mV of dropout at full load, a 170 microamp quiescent current and a bypass pin for the reference in a SOT-23 (DBV) body of 6 pins. The adjustable version brings the feedback node and a bypass pin out to the package, sets the output from 1.22 V to 5.2 V with two external resistors against a 1.2246 V reference, holds 1 per cent at 25 C, starts in 63 microseconds and stays stable with a 1 microfarad ceramic output capacitor. The addendum dated 15 September 2026 marks this ordering string NRND.
Order code and package
| TPS79101DBVR | SOT-23 (DBV) body, 6 pins, 2.90 mm by 1.60 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C with unlimited floor life, marking PEUI, status NRND in the addendum dated 15 September 2026 |
| TPS79101DBVRG4 | the same die and body with the G4 finish suffix, same 3000 piece reel, same marking and the same NRND status |
| TPS79101DBVT | a small reel string that the addendum lists on a 5 pin body with marking PERI, which does not match the six pin adjustable pin out, so the string has to be confirmed before an order goes out |
| Fixed siblings | TPS79118, TPS79133 and TPS79147 are the 1.8 V, 3.3 V and 4.7 V fixed members on the 5 pin body, and their status is mixed: some rows read active, some NRND, and at least one reads obsolete |
| Temperature | minus 40 C to 125 C on every row, which is the junction range the electrical tables are written against |
| Family | the TPS792xx parts are the same regulator with a different enable polarity, and they share the body and the pin count |
| Marking | PEUI on the adjustable rows and PERI or PETI on the fixed rows, so a reel can be told apart from the label alone |
Electrical parameters that decide the application
| Input voltage | 2.7 V to 5.5 V, with the minimum input for a given output set by the output plus the dropout at full load |
| Output current | 100 mA continuous, limited by the internal protection rather than by the package |
| Output voltage | 1.22 V to 5.2 V on the adjustable version, set by the ratio of two resistors against the 1.2246 V reference |
| Reference | 1.2246 V typical, brought out through the FB pin on the adjustable version and trimmed inside the package on the fixed versions |
| Dropout | 38 mV at 100 mA on the 4.7 V version, which is the figure that lets a 5 V rail feed a 4.7 V load from a 5 V bus |
| Quiescent current | 170 microamp typical at 25 C with any load between zero and 100 mA, which is low enough for a rail that is always on |
| Noise | 15 microvolt RMS on the 1.8 V version with a 0.1 microfarad bypass capacitor on the BYPASS pin, and the bypass pin is present on the six pin body |
| Supply rejection | 70 dB at 10 kHz, which is the number that matters when the input carries a switching regulator ripple |
| Start up | 63 microseconds to regulation with a 0.001 microfarad bypass capacitor, which is fast enough to follow a sequenced rail |
| Stability | stable with any 1 microfarad ceramic output capacitor, with no minimum equivalent series resistance to add |
| Line and load regulation | 0.05 per cent per volt of line change at 25 C, with the load transient behaviour set by the output capacitor |
| Enable | an active high enable pin, and the regulator drops below 1 microamp of supply current when it is held low |
| Accuracy | 1 per cent at 25 C over the full output range, which is why the reference is trimmed rather than left as a nominal |
Family variants and how they differ
| Adjustable and fixed | the 01 string is adjustable and needs the six pin body for the FB and BYPASS pins, while the 18, 33 and 47 strings are fixed and use the five pin body |
| Bypass pin | the BYPASS pin is the difference between the data sheet noise figure and a much higher number, because the 15 microvolt RMS is measured with a capacitor on it |
| Enable polarity | the TPS792xx family inverts the enable sense, so a board written for one is not a drop in for the other even though the body is the same |
| Lifecycle | the adjustable string is NRND and the fixed strings are split between active, NRND and obsolete, so a long life product needs a plan rather than a stock position |
| Body | the six pin SOT-23 is 2.90 mm by 1.60 mm with 0.95 mm pitch, and the five pin body is the same size with one pin removed |
| Marking | PEUI, PERI and PETI are three different codes on the same body size, which is the fastest way to identify a mixed reel |
Points to check before this part goes on a BOM
This string is NRND. The addendum dated 15 September 2026 carries TPS79101DBVR and its G4 variant as NRND, the not recommended status, so a new board should be quoted against a replacement rather than against this string, and an existing board should plan a last time buy.
The data sheet promises 15 microvolt RMS of noise and the measurement needs a capacitor. The BYPASS pin is what makes that true, and a board that leaves it open gets a noticeably higher noise floor on a phase locked loop or a voltage controlled oscillator supply.
The five pin DBVT row in the addendum does not match the six pin adjustable pin out. The table lists it with a different marking, so the exact string has to be confirmed with the supplier before a purchase order is raised.
The dropout is quoted on the 4.7 V version at 100 mA. On a 1.8 V output the same 100 mA produces a different dropout, and the minimum input voltage for the rail has to be calculated from the curve rather than from the headline number.
Start up in 63 microseconds is fast enough to be a problem. A rail that comes up before the load is ready can latch a processor, so the enable pin is usually driven from a sequencer rather than tied to the input.
Why a 100 mA LDO still sits on new boards
The rail it feeds is usually a clock, a phase locked loop, a data converter reference or a radio bias, where the current is under 100 mA and the requirement is noise rather than efficiency. A switching regulator in front of those loads needs a filter, and a linear regulator with 70 dB of rejection at 10 kHz does the job with two capacitors.
The adjustable version is used when the rail is not one of the standard values. A 1.5 V or 2.5 V reference rail comes from the same part with two resistors, and the reference tolerance of 1.2246 V plus the resistor tolerance is what sets the accuracy of the load.
Where this order code fits
The part suits a supply for a voltage controlled oscillator, a phase locked loop, a Bluetooth or wireless LAN front end, or a portable instrument, where 100 mA is enough and noise is the constraint. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Is this part still produced? The addendum marks the DBVR and DBVRG4 strings NRND. That means the part is not recommended for new boards, not that it has stopped shipping, and a requirement is met from stock or from a franchised source while a replacement is qualified.
What replaces it on a new board? A lower noise or lower quiescent current regulator in the same 100 mA class, chosen against the same three numbers: noise with the bypass capacitor fitted, rejection at the ripple frequency, and dropout at full load.
How is the output set on the adjustable version? Two resistors from the output to the FB pin and from the FB pin to ground, with the ratio against the 1.2246 V reference setting the rail. The 1.22 V to 5.2 V window is the range the loop is specified over.
Does it need a minimum output capacitor? Yes, 1 microfarad of ceramic, and it is stable with any part that meets that value with no minimum equivalent series resistance. A larger capacitor slows the transient and costs board area, and it does not improve the noise floor, which is set by the bypass capacitor.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.