Contact Us

TPS77516PWPR

Brand: Texas Instruments
Texas Instruments TPS77516PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS77516PWPR — Power Management & Signal Chain | Superb Automation

TPS77516PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS77516PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS77516PWPR 1.6 V regulator in the 20 pin PowerPAD body

The TPS77516PWPR is the 1.6 V member of the TPS775 family in the 20 pin HTSSOP body with an exposed thermal pad, ordered on a 2000 piece reel. Electrically it is the same 500 mA regulator as the SOIC member, with 169 mV of typical dropout on the 3.3 V point of the family, 2 per cent tolerance and 85 microamp of quiescent current, and it carries the same open drain reset output with a 200 millisecond delay. The body is the difference: the PowerPAD takes the heat into the board instead of into the air, which is what a 500 mA rail needs when the input is 3.3 V and the output is 1.6 V.

The dissipation arithmetic is what decides between the two bodies. At 500 mA, 3.3 V in and 1.6 V out, the part turns 850 mW into heat; the HTSSOP with a thermal pad and a via array spreads that into the copper, while the eight pin SOIC relies on the lead frame and the pour beside it. Both are rated for the same junction temperature, so the choice is a question of board area and airflow rather than of silicon. The reel is 2000 pieces, the moisture level is 2 with a one year floor life, and the top side marking is PT77516.

Key parameters printed in the SLVS232J document

Output1.6 V fixed, one of the fixed members of the family from 1.5 V to 3.3 V
Load current500 mA
Dropout169 mV typical at 500 mA on the 3.3 V member of the family
Accuracy2 per cent over the specified conditions
Quiescent current85 microamp typical over the full load range
Current limit1.2 A typical, 1.6 A maximum
Rejection60 dB at 1 kHz with a 10 microfarad output capacitor
ResetOpen drain, 200 millisecond delay, valid above 1.1 V of input

Package, reel and top side marking

PackageHTSSOP, PWP body, 20 pins, exposed thermal pad
Reel2000 pieces on a large tape and reel, 70 pieces in a tube for the plain PWP row
Finish and moistureNickel palladium gold, moisture level 2, one year floor life
Temperature and markingMinus 40 to plus 125 degrees on the reel row, top side marking PT77516

Where the PowerPAD body is the reason to choose this code

A 1.6 V rail usually feeds a DDR memory termination or an auxiliary supply on an FPGA, both of which are sensitive to the transient rather than to the steady state. The 500 mA rating covers a memory bank that is being refreshed, and the reset output gives the controller a clean release after the rail is up. Where the same rail has to be duplicated on several boards in one chassis, the 2000 piece reel is the practical unit, because it matches a panel build better than a 75 piece tube and avoids repeated line changes.

There is a documentary wrinkle worth knowing before a purchase order goes out. In the SLVS232J addendum the rows for the SOIC body of this voltage print minus 40 to plus 85 degrees while the PWPR row prints minus 40 to plus 125 degrees, so the same die appears under two temperature claims in one table. The reel row is the one that matters for this code, and the drawing should quote the row rather than the family text. A second point is the reel letter: the plain PWP row is a 70 piece tube and the R row is 2000 pieces on a large reel, which the interleaved columns of the addendum do not make obvious; the date code management page describes how SUPERB checks the reel label against the addendum row at goods in.

Questions buyers ask before ordering

Is the thermal pad connected to ground? Yes, and it has to be soldered to a copper area with vias. A pad left floating loses the thermal path the body was chosen for, and the junction temperature figure in the document no longer applies.

Does the 1.6 V member need a different output capacitor? No. The loop is the same as the rest of the family and is stable with a 10 microfarad low ESR capacitor, which is the value the transient response is quoted against.

Why does the addendum print two temperature ranges? The catalog rows of the family carry two claims in one table. The PWPR row is minus 40 to plus 125 degrees, which is the figure to quote when the drawing names this code.

Ordering this part through SUPERB

SUPERB supplies this regulator against a bill of materials line, confirms the reel size and the moisture level against the addendum row, and keeps the date code with the certificate. Send the rail, the load and the target date through the BOM shortage recovery page when the line needs the part before the scheduled delivery, and the answer comes back with what is on the shelf and what has to be pulled forward.