Contact Us

TPS767D301QPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS767D301QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS767D301QPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS767D301QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS767D301QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS767D301QPWPRQ1 dual output regulator, 3.3 V plus adjustable, 1 A each

The TPS767D301QPWPRQ1 is a dual low dropout regulator in the 28 pin PowerPAD TSSOP body. Regulator two is fixed at 3.3 V, regulator one is adjustable from 1.5 V to 5.5 V with two external resistors, and each side sources up to 1 A. The two regulators share a die but not a control loop, and each carries its own open drain reset output with a 200 millisecond delay, which is the reason the part survives in split supply systems where a processor needs core and input output rails that come up in a fixed order.

Quiescent current is 85 microamp typical per regulator over the whole load range, and the standby current with the enable held low is 1 microamp. Dropout on the 3.3 V member is 350 mV typical at 1 A, so a 5 V input leaves more than a volt of headroom and the dissipation is about 1.7 W per side at full load, which is why the PWP body with its exposed pad is the one used. The reset comparator trips at 92 to 98 per cent of the regulated output with 0.5 per cent of hysteresis, and the input has to stay above 1.1 V for the reset output to be valid.

Key parameters printed in the SLVS209H document

OutputsRegulator one adjustable 1.5 V to 5.5 V, regulator two fixed 3.3 V
Load current1 A per regulator, output current limit 2 A per side
Dropout350 mV typical at 1 A for the 3.3 V member, proportional to load
Accuracy2 per cent over line, load and temperature
Quiescent current85 microamp typical per regulator across the full load range
Standby current1 microamp with the enable held low
Rejection60 dB at 1 kHz with a 10 microfarad output capacitor
ResetDual open drain output, 200 millisecond delay, trip at 92 to 98 per cent of output

Package, reel and top side marking

PackageTSSOP, PWP body, 28 pins, PowerPAD thermal pad
Reel2000 pieces on a large tape and reel
Finish and moistureNickel palladium gold, moisture level 3 with a 168 hour floor life on the automotive row
Temperature and markingMinus 40 to plus 125 degrees, marking per the addendum row

Where a dual regulator earns its board area

This part is chosen when one package has to deliver the 3.3 V peripheral rail and an adjustable core rail together, usually in an industrial controller where board area is short. The adjustable side takes the core voltage, and because the reference is internal the divider is the only external part that sets it. The reset outputs can be tied to the processor reset through a single pull up if both rails have to be valid before release, or kept separate if the core is allowed to start first. The power management cross reference page lists the dual regulators that share the 28 pin footprint for a second source.

The caveat on this order code is documentary. The staged vendor document is the catalog revision of the family and does not print the Q1 row in its addendum, so the automotive orderable record for this suffix has to be confirmed on the vendor product folder before a purchase order is released. That is not a reason to avoid the part; it is a reason to ask for the addendum page with the order and keep it with the certificate. Where the program runs for a decade, the second source question comes up early, and the obsolete part cross reference hub page is the place to start when a family row moves to not recommended for new builds.

Questions buyers ask before ordering

Do both regulators need a 10 microfarad output capacitor? The document specifies stability with a 10 microfarad low ESR capacitor on each output. Smaller values change the transient response and the phase margin, so the figure should be treated as a requirement.

Is the 200 millisecond reset delay fixed? Yes, it is internal. The TPS768 family is the one that offers the same regulator with a power good output instead of a reset, for applications that need a flag rather than a reset.

Why does the automotive row show moisture level 3? The Q1 row in the addendum prints level 3 with a 168 hour floor life while the catalog row prints level 1. The body is the same, so the difference is the finish and the handling requirement written into the automotive record.

Ordering this part through SUPERB

SUPERB supplies this part against a bill of materials line, confirms which addendum row applies to the Q1 suffix before quoting, and keeps the reel label and the certificate together so the moisture level is documented at goods in. A quantity and a target date are enough to start; send the list through the kitting service page when the two rails and their passives should arrive as one kit.