Contact Us

TPS76633DR

Brand: Texas Instruments
Texas Instruments TPS76633DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS76633DR — Power Management & Signal Chain | Superb Automation

TPS76633DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS76633DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS76633DR: 250 mA, 16 V low dropout regulator in an 8 pin SOIC, two silicon generations under one part number

TPS76633DR is a linear regulator that drops a 12 V or 15 V rail to a clean 3.3 V for analogue and gate drive loads in a SOIC body of 8 pins. It delivers 250 mA with a 16 V input ceiling on the current silicon and a 225 mV dropout at full load, and it is stable with a 2.2 uF output capacitor. The same part number has shipped on two chips: the older one is rated 2.7 V to 10 V with 3 per cent accuracy, the current one 2.5 V to 16 V with 1 per cent.

Order code and package

TPS76633DR8 pin SOIC (D), 4.9 mm by 6.0 mm, active, the reel quantity on this row reads call TI
TPS76633DRM3same body and silicon, 2500 pieces on a large reel, the row that carries a published quantity
TPS76633Dthe tube row, obsolete, so a through hole or tube feed line has to move to the reel
Output voltage, 33 suffix3.3 V fixed, trimmed in the factory, no divider
Accuracy, current silicon1 per cent over load and temperature, against 3 per cent on the older chip

Electrical parameters that decide the application

Input voltage, current silicon2.5 V to 16 V, with 18 V as the absolute maximum
Input voltage, older silicon2.7 V to 10 V, with 13.5 V as the absolute maximum
Output current250 mA, with the current limit acting above that
Output voltage range1.2 V to 12 V fixed, 0.8 V to 14.6 V adjustable on the current silicon
Dropout voltage225 mV typical at 250 mA on the 5 V member, lower on the 3.3 V member at the same current
Quiescent current55 uA typical on the current silicon, 35 uA on the older chip
Shutdown current4 uA maximum on the current silicon, 10 uA maximum on the older chip
Ripple rejectionbetter than 70 dB at 1 kHz and 46 dB at 1 MHz on the current silicon
Soft start750 us typical internal ramp, which is what keeps the inrush off the input rail
Output capacitor2.2 uF or larger, stable across the range, no ESR window to meet

Two chips under one part number

Input ceiling10 V on the older chip, 16 V on the current one, so a 12 V rail is only safe on the current one
Accuracy3 per cent against 1 per cent over load and temperature
Output window1.5 V to 5 V fixed on the older chip, 1.2 V to 12 V on the current one
Quiescent current35 uA constant across load on the older chip, 55 uA on the current one
Power goodopen drain, active high, usable as a reset for the load or a low battery flag
Enable pina TTL high puts the part to sleep, which is inverted from most regulators and is worth checking on a board that reuses an older net
Family rows76601 adjustable, 76615 1.5 V, 76618 1.8 V, 76625 2.5 V, 76628 2.8 V, 76630 3.0 V, 76633 3.3 V, 76650 5.0 V

Points to check before this part goes on a BOM

The 16 V input rating belongs to the current silicon, and the older chip inside the same part number stops at 10 V. A 12 V rail feeding this part is fine today and was not fine on the earlier chip, which is the sort of thing that only shows up when a line swaps a reel from an older lot. Any incoming inspection on this part number should confirm the chip generation, and the 1 per cent accuracy row is the quickest way to tell them apart on the bench.

The enable pin works backwards from what most boards expect. A TTL high puts the regulator into sleep, so a net that was pulled high by default on an earlier board now holds the rail off. On a board that reuses an old net name this is a real failure mode, and it is worth a few minutes on the bench before a build is released, particularly when a part is being second sourced into an existing board.

The dropout of 225 mV at 250 mA is quoted on the 5 V member, and the 3.3 V member sits lower at the same current because the pass element is the same and the headroom is larger. The number that matters on a 12 V to 3.3 V rail is not dropout at all, it is dissipation: 8.7 V across the pass element at 250 mA is 2.2 W in an 8 pin SOIC, which needs copper and cannot be run at 85 C ambient without a calculation.

Two silicon generations inside one order code also means two sets of output capacitor requirements. The current chip is stable with 2.2 uF and quotes ripple rejection to 1 MHz, the older chip wants a larger capacitor and has a narrower rejection curve. A board that was characterised with the older part and is now built with the current one usually works, but the transient response changes, and that is worth knowing before a customer reports a different settling time.

The power good output is open drain and active high, so it needs a pull up and it goes low when the output is out of regulation. That makes it useful as a reset for whatever sits downstream, and it is the reason the part appears on boards with a processor that needs a clean release after the rail is up. It is not a delay element by itself: the 750 us soft start sets how long the rail takes, and the flag follows it.

The published order rows are inconsistent in a way that matters for purchasing. The DR row is active but its quantity column reads call TI, while the DRM3 row carries a published 2500 piece large reel, and the tube row is obsolete. A buyer who needs a reel should name the DRM3 string on the purchase order, and a buyer who orders the plain DR string may be told the quantity is not published rather than that the part is unavailable.

The 2.2 uF output capacitor is the only external part the regulator needs, and the vendor is explicit that a larger value is acceptable. What is not optional is the input capacitor: a 12 V rail with a long trace to the regulator will ring at the input on a load step, and the part has no input clamp of its own. The application circuits put 1 uF or more at the input pin for that reason.

Where this order code fits

It is the post regulator behind a 12 V or 15 V rail: analogue front ends, gate drive bias for silicon carbide parts, microphone bias and the supply pin of a microcontroller that cannot tolerate switching ripple. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the 16 V input rating valid on every reel of this part number? Only on the current silicon. The older chip inside the same order code is rated to 10 V, so a 12 V rail requires the current chip and a check on incoming lots.

Why does the tube row show obsolete while the reel is active? The vendor has retired the tube packing for this part number while keeping the large reel in production. A line that feeds from tubes has to move to reel handling or to a different package from the same family.

Can this part drop 12 V to 3.3 V at 250 mA continuously? Electrically yes, thermally it is 2.2 W in an 8 pin SOIC. That needs copper area and a lower ambient, or a switching regulator ahead of it.

What sets the output voltage? The 33 suffix is factory trimmed to 3.3 V with no divider. The 01 suffix is the adjustable member of the same family with a 1.25 V reference on the older chip and 0.8 V on the current one.

How is the enable pin used? Pull it low to run and high to sleep. That is inverted from most regulators, so a board that ties enable to the input rail through a resistor keeps the part off.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.