Contact Us

TPS74901RGWR

Brand: Texas Instruments
Texas Instruments TPS74901RGWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS74901RGWR — Power Management & Signal Chain | Superb Automation

TPS74901RGWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS74901RGWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS74901RGWR: 3 A low dropout regulator with a bias rail and power good

TPS74901RGWR is a 3 A linear regulator that runs from an input as low as 0.8 V by taking its gate drive from a separate bias rail in a VQFN (RGW) body of 20 pins. The output is set from 0.8 V to 3.6 V by an external divider, the bias rail accepts 2.7 V to 5.5 V, and a power good output plus an active high enable allow the rail to be sequenced with the supplies around it.

Order code and package

Order code read outTPS74901 RGW R: family, RGW 20 pin VQFN 5 mm by 5 mm, R tape and reel
PackageVQFN (RGW), 20 pins, 5.00 mm by 5.00 mm, 1 mm tall, thermal pad
Other bodiesDRC, 10 pin VSON 3 mm by 3 mm, and KTW, 7 pin DDPAK, which the vendor identifies as the legacy chip
Carrierlarge tape and reel for the RGW body
Operating temperatureminus 40 to plus 125 degrees Celsius, fully specified across the range
Output capacitorstable with any capacitor of 2.2 microfarad or more, ceramic included
Bias supply2.7 V to 5.5 V, or the output plus the bias dropout, whichever is higher

Electrical parameters that decide the application

Input voltage0.8 V to 5.5 V, which is the point of the part, a 1 V rail can feed a 0.9 V output
Output voltage0.8 V to 3.6 V adjustable, set by two resistors
Output current3 A continuous
Dropout120 mV typical at 3 A, the guaranteed figure is quoted in the electrical table over temperature
Accuracy1 percent over line, load and temperature on the current chip, 2 percent on the legacy chip
Bias current paththe bias rail supplies the gate drive, so the input can sit close to the output without starving the pass element
Soft startset by a capacitor on the SS pin, monotonic by construction, which matters when a processor has a strict ramp requirement
Power goodopen drain output with a threshold tied to the feedback node, usable as a sequencing signal
Input capacitor4.7 microfarad recommended when the input and bias pins share one supply
Referencethe feedback threshold is fixed and the output is set by two resistors, so divider tolerance adds to the regulator error
Power good thresholdtied to the feedback node, so the flag tracks the output rather than a separate sense pin

Family variants and how they differ

RGW20 pin VQFN 5 mm by 5 mm, current chip, 1 percent accuracy
DRC10 pin VSON 3 mm by 3 mm, the same silicon in the smallest body
KTW7 pin DDPAK, the legacy chip at 2 percent accuracy, which is the body that catches people out
Practical effectthe same order code stem exists in three bodies with two accuracy grades, so a package change is not free

Points to check before this part goes on a BOM

The package decides the accuracy grade. The vendor describes the DDPAK body as the legacy chip and specifies 2 percent over line, load and temperature for it, while the current chip in the VQFN and VSON bodies holds 1 percent. A board that moves from the through hole part to the surface mount part gains accuracy, and a board that moves the other way loses half of it without any change to the circuit.

The bias rail is not optional when the input is low. With a 1.2 V input and a 1.0 V output the pass element has 200 mV to work with, and the gate drive comes from the bias pin, which wants at least 2.7 V or the output plus the bias dropout. Tying the bias pin to the same 1.2 V rail removes the whole reason to use this part, and the regulator will simply follow the input down.

The accuracy specification carries its own bias condition. The electrical table states the tight limit for the case where the bias rail sits at least 2.2 V above the output. A board that runs the bias pin at 2.5 V with a 1.8 V output is 0.7 V above the output, which is inside the operating range but outside the condition the tight number was measured under, so the budget should use the looser figure.

120 mV at 3 A is a typical value. The guaranteed dropout is a separate row in the electrical table and it is larger, which is the number to use when the input rail has a tolerance of plus or minus 5 percent. A 3.3 V rail at the low end is 3.135 V, and a 3.0 V output at 3 A needs the maximum dropout, not the typical one, to stay in regulation.

Thermal budget starts at the dissipation, not the current. Dropping 3.3 V to 1.2 V at 3 A is 6.3 W in a 5 mm by 5 mm body, which no board survives without a copper pour and airflow. The 3 A rating is real, and it belongs to a low input to output differential, which is why the part pairs with a switcher in front of it rather than replacing one.

The power good output is a sequencing tool, not a fault indicator. Its threshold follows the feedback node, so it releases when the output is inside regulation and drops when the rail sags. Wired to the enable of the next regulator, it produces a clean cascade without a supervisor, and a board that leaves the pin open loses nothing electrically but loses the ordering.

The soft start capacitor is a load protection device. A 3 A rail feeding a large bank of ceramic capacitors draws a current step at enable that the upstream supply may not survive, and the SS pin turns that step into a ramp. The ramp is monotonic by construction, which matters for processors that latch a fault if the core rail dips during start up.

Where this order code fits

These parts power FPGAs, DSPs and network processors from a low voltage bus, in rack servers, network interface cards, storage arrays and merchant power supplies, where a 1.2 V or 1.8 V rail has to be cleaned up after a switcher. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Can I run it from 5 V and get 3.3 V at 3 A? Yes, and that is the easy case for dropout, but 5.1 W of heat has to leave the package. The bias pin can share the 5 V rail with a 4.7 microfarad input capacitor.

Do I need the bias rail at all? Only when the input is close to the output. Above roughly 3 V of input headroom the bias pin can be tied to the input, and below that the rail is what keeps the pass element in regulation.

Which body should a repair order specify? The one on the board. RGW and DRC carry the current chip, KTW is the legacy chip, and the three are not interchangeable without a footprint change.

Is it stable with a ceramic output capacitor? Yes, any capacitor of 2.2 microfarad or more, ceramic included. There is no minimum ESR requirement, which is what makes the part easy to use with modern capacitors.

Can the input really be 0.8 V? Yes, with the bias rail present. The pass element needs gate drive above the output, and the bias pin is where it comes from, so the input can sit below the usual 1.4 V floor.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.