Contact Us

TPS74701QDRCRM3Q1

Brand: Texas Instruments
Texas Instruments TPS74701QDRCRM3Q1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS74701QDRCRM3Q1 — Power Management & Signal Chain | Superb Automation

TPS74701QDRCRM3Q1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS74701QDRCRM3Q1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS74701QDRCRM3Q1: a 500 mA low dropout regulator with a separate bias rail and programmable soft start

TPS74701QDRCRM3Q1 is a 500 mA linear regulator that holds a 0.8 V to 3.6 V output in regulation from an input as low as 0.8 V, taking its gate drive from a second bias rail instead of from the input in a VSON body of 10 pins. The separate bias pin is what makes the part useful on a 1.2 V or 1.5 V rail, where the input headroom is too small to drive the pass FET on its own.

Order code and package

Catalogue stringTPS74701QDRCRM3Q1, the code printed in the page title
BodyDRC, VSON, 10 pins, 3.00 mm by 3.00 mm by 1.0 mm
Reel3000 pieces on a large tape and reel, the quantity printed for the TPS74701DRCRM3 row
Finish and moistureNIPDAU plating, moisture level 2, 260 C, one year floor life
Temperaturejunction range minus 40 to 125 C
MarkingCEG
DocumentSBVS099H, revised April 2023
Suffix checkthe addendum prints TPS74701DRCR, TPS74701DRCR.A, TPS74701DRCRG4 and TPS74701DRCRM3, and no row carries a Q1 suffix, so the Q1 in the catalogue string is not confirmed by the vendor list

Electrical parameters that decide the application

Input range0.8 V to 5.5 V at IN, which is below the 1.2 V core rails this part normally feeds
Bias range2.7 V to 5.5 V at BIAS, and the bias must sit at least 1.62 V above the nominal output for the published dropout figure
Output range0.8 V to 3.6 V, set by an external divider on FB
Reference0.796 V minimum, 0.800 V typical, 0.804 V maximum at 25 C junction
Accuracy, M3 rowsminus 0.95 to plus 0.95 per cent over line, load and temperature in the separate M3 table
Accuracy, other rows2 per cent over line, load and temperature in the features list
Dropout at IN35 mV typical at 500 mA on the M3 rows, with the bias rail supplying the gate drive
Current limit1.1 A minimum, 1.25 A typical, 1.3 A maximum at 80 per cent of the nominal output
Soft start530 nA of charging current into the SS capacitor, so the ramp is set by the capacitor value and the reference, not by a fixed timer
Minimum start-up250 us with the SS pin open and a 1.0 A load
Enable thresholds1.1 V high and 0.4 V low, with 55 to 94 uA of pin current
Power goodopen drain output that pulls to 0.05 V or lower at 1 mA of sink current, with 0.1 uA of leakage when released
Output capacitorstable with any capacitor of 2.2 uF or more, ceramic or otherwise, which removes the ESR window that older regulators demanded
Thermal shutdown165 C rising and 140 C falling

Family rows and what the suffixes change

TPS74701DRCRactive, 3000 piece large reel, the plain string with no letter suffix
TPS74701DRCR.Aactive, same reel, the revision letter row that the addendum prints separately from the plain one
TPS74701DRCRG4active, same reel, the green material row
TPS74701DRCRM3active, same reel, the tighter accuracy and lower dropout rows used on this page
TPS74801the same 3 by 3 mm body and pinout at 1.5 A, which is the part to look at when the rail grows
Colour coded suffixthe M3 letter sits after the reel letter, so it is the silicon revision and not a packing change

Points to check before this part goes on a BOM

The Q1 suffix in the catalogue string is the one thing to settle before a purchase order goes out. Four rows are published for this body and none of them carries a Q1, so a buyer who needs an automotive grade part should ask for the qualification document against the exact string on the order rather than assume the suffix was printed by the vendor.

M3 silicon is specified in its own table. The accuracy window there reads minus 0.95 to plus 0.95 per cent, and the dropout at 500 mA reads 35 mV typical, both tighter than the 2 per cent and 50 mV carried in the features list for the older rows. A budget built on the features list is therefore conservative rather than optimistic, which is the safe direction.

The bias rail is not a convenience. With BIAS at 2.7 V to 5.5 V and the input as low as 0.8 V, the regulator can hold a 1.0 V core rail from a 1.2 V supply that would otherwise leave the pass FET without enough gate voltage. Teams that tie BIAS to IN give that advantage away and drop back to the headroom of a conventional regulator.

Dropout in the vendor table is measured at the point where the output falls 3 per cent below nominal, not at the point where regulation stops altogether. A 35 mV typical figure therefore describes a small sag, and a rail riding 30 mV above the requirement is already inside the sag rather than outside it.

Stability with any capacitor of 2.2 uF or more is worth more than it looks on a dense board. There is no ESR window to police, so a small ceramic in a 0402 body and a larger polymer part both work, and the second source question becomes a question of tolerance rather than of chemistry.

Power good is open drain and pulls to 0.05 V at 1 mA. It can therefore be wired to a rail above the output, which is what makes it usable as a sequencing signal for the next regulator rather than only as a monitor for the local rail.

How the bias rail changes the input range

On a conventional regulator the gate of the pass FET is driven from the input, so the input has to sit a gate threshold above the output before the FET is fully on. Taking 2.7 V to 5.5 V at BIAS moves that drive to a rail that does not sag with the load, and the input only has to cover the channel resistance and the reference.

The published condition is a bias at least 1.62 V above the nominal output. On a 1.5 V rail that means 3.12 V or more at BIAS, which is normally the 3.3 V rail already on the board. On a 0.9 V rail a 2.7 V bias is enough, so the same part serves both rails with the same resistor divider.

The bias current is small, 1 mA in the table, but it does not fall with load, so it belongs in the standby budget of the rail that feeds it rather than in the load budget of the regulator.

Soft start as a current source, not a timer

The SS pin charges at 530 nA. The ramp time therefore follows the capacitor value directly and there is no fixed internal timer to fight against. With the pin open the start-up is 250 us, which is short enough that inrush into a large output capacitor becomes the visible problem.

Because the ramp is monotonic, a processor fed from this rail sees a single clean rise and no dip in the middle. That matters on FPGA and DSP supplies where a non monotonic ramp can leave the device in a latched state that only a power cycle clears.

Where this order code fits

This is the part teams reach for when a 1.2 V or 1.5 V core rail has to be generated from a supply that is only a few hundred millivolts above it, and when the sequencing of that rail against the I/O rail has to be controlled. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Can the bias pin be tied to the input? Yes, and the regulator still works. What is lost is the low input capability, because the gate drive then depends on the input headroom. On a 1.8 V input feeding a 1.5 V output the difference is small, on a 1.2 V input feeding a 1.0 V output it is the whole margin.

What sets the output voltage? A divider from OUT to FB to ground against the 0.8 V reference. The reference window is 0.796 V to 0.804 V at 25 C, so divider tolerance and reference tolerance add up, which is why the accuracy rows quote the reference separately.

Is a 2.2 uF ceramic enough at 500 mA? The vendor states stability with any capacitor of 2.2 uF or more, so yes for stability. Load transient is a different question: the same capacitor has to supply the current until the loop responds, and 2.2 uF in a 0603 body loses capacitance under bias, so the effective value is what counts.

How is power good used for sequencing? It is open drain, so it can be pulled to any rail up to its rating and wired into the enable of the next regulator. The trip point sits near 90 per cent of the nominal output, which means the next rail starts only after this one is substantially up.

What happens at thermal shutdown? The output turns off at 165 C junction and returns at 140 C. That 25 C of hysteresis is deliberately wide, so a board sitting at the edge of its thermal budget does not oscillate between on and off.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.