Contact Us

TPS73701DRBR

Brand: Texas Instruments
Texas Instruments TPS73701DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73701DRBR — Power Management & Signal Chain | Superb Automation

TPS73701DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73701DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73701DRBR: 1 A low dropout regulator, adjustable 1.20 V to 5.5 V, reverse current protection, WSON-8

TPS73701DRBR is an adjustable low dropout linear regulator rated 1 A with an NMOS pass element and reverse current protection in a WSON body of 8 pins. The NMOS pass element in a voltage follower arrangement makes the loop insensitive to the output capacitor value and its equivalent series resistance, so a 1 microfarad ceramic is enough even at 1 A. The adjustable version sets the output from 1.20 V to 5.5 V with two resistors, which is why this string appears on boards that need a core rail between the standard fixed options.

Order code and package

TPS73701DRBRActive, WSON-8, 3000 pieces on a large reel, NIPDAU finish, MSL-1-260C unlimited floor life
TPS73701DRBTActive, 250 pieces on a small reel, the same body
TPS73701DCQActive, the SOT-223 body, 78 pieces in a tube, for through hole style repair work
Fixed versionsthe family also carries fixed outputs, which are different ordering strings and are not interchangeable with this adjustable part
Temperature rangeminus 40 to 125 degrees junction on the published rows

Electrical parameters that decide the application

Input voltage2.2 V to 5.5 V
Outputadjustable from 1.20 V to 5.5 V through an external divider
Output current1 A
Dropout130 mV typical at 1 A on the legacy silicon, 122 mV on the new silicon
Initial accuracy1 per cent
Accuracy over line, load and temperature3 per cent on the legacy silicon, 1.5 per cent on the new silicon
Shutdown currentless than 20 nanoamp typical
Output capacitorstable with 1 microfarad ceramic, insensitive to ESR

Family variants and how they differ

TPS73701adjustable, the string on this page
Fixed membersset by the ordering suffix, same body and pinout, no divider needed
TPS7A37the higher accuracy sibling at 1 per cent over temperature, for a rail that is also a reference
DRB body3 mm by 3 mm WSON with the thermal pad on the underside
DCQ bodySOT-223 with a visible tab, used where hand soldering is needed

Points to check before this part goes on a BOM

There are two silicon generations under one part number. The data sheet distinguishes the legacy silicon from the new silicon, and the difference is in the accuracy: 3 per cent over line, load and temperature on the old chip and 1.5 per cent on the new one. The dropout figure also moves, 130 mV against 122 mV. A rail specified against one generation and built with the other is still inside its absolute limits but not inside the error budget it was signed off against.

The adjustable version needs a divider and the divider costs accuracy. The 1 per cent initial accuracy is at the feedback pin, so the divider tolerance and its temperature drift add to it. Two 0.1 per cent resistors keep the total under 1.5 per cent; two ordinary 1 per cent parts make the rail a 2 per cent rail, which is the number that ends up on the test report.

Reverse current protection is unusual in an LDO. An NMOS pass element with the body diode pointing the wrong way would normally conduct from output to input when the output is held above the input. The part limits that leakage, which matters on a board where a rail can be back fed during a test or where a second supply holds the output up after the input collapses.

One hundred and thirty millivolt dropout at 1 A is low but not zero. A 1.2 V output from a 1.5 V input works. A 1.2 V output from a 1.3 V input does not, and the rail follows the input down. The 2.2 V minimum input means the part cannot be used on a 1.8 V rail to make 1.2 V, which is a common mistake when a board moves to a lower core voltage.

The NMOS topology is why a 1 microfarad capacitor is enough. A bipolar LDO with a similar current rating usually needs 10 microfarad or more and a specific ESR range. Here the loop is stable with a small ceramic, which saves board area and removes the risk of fitting an electrolytic with the wrong ESR.

Less than 20 nanoamp in shutdown is a genuine off state. That is low enough that the regulator disappears from a sleep budget. It also means the enable pin has to be driven, not left floating, because a floating enable on a high impedance pin can sit at a level that turns the part partially on.

The WSON pad is the only thermal path at 1 A. At 1.8 V in and 1.2 V out the dissipation is 0.6 W, which the 3 mm body can carry only if the pad is soldered to a copper island with vias. At 5 V in and 1.2 V out it is 3.8 W, which no linear regulator in this body can carry, and the part will thermal cycle.

The tube option matters for repair work. The SOT-223 body in a tube is the one a repair bench can handle, because the WSON has no visible leads. For volume the WSON on a large reel is the cheaper route, and for a service spare the tube is the one that arrives usable.

Do not confuse this with the fixed member of the same family. The fixed versions look identical and ignore the divider, so a board that expects an adjustable part and receives a fixed one produces the internal voltage regardless of the resistors fitted. The ordering string is the only reliable field on the label.

What to confirm before this part goes on a purchase order

Confirm the output voltage and whether the board divides it externally. The adjustable string and the fixed strings share a body and cannot be told apart once the reel is open.

Ask whether the customer needs the accuracy of the new silicon or has qualified against the legacy chip. That is a question about the error budget on their test report, and it cannot be answered from the part number alone.

The reel size is the last field to check: 3000 on a large reel for the WSON body, and a tube of 78 for the SOT-223 body that a repair bench can handle.

Where this order code fits

It post regulates a 1 A rail for a DSP, an FPGA or an ASIC core from a 3.3 V or 5 V bus, where the dropout has to stay small enough to run from a 3.3 V input. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it make 1.2 V from a 1.8 V rail? Yes. The dropout is 130 mV at 1 A, so 1.8 V in leaves 600 mV of headroom and the part runs comfortably. The dissipation at 1 A is 0.6 W, which the WSON body handles with a proper pad.

Does it need a minimum ESR output capacitor? No. The NMOS loop is stable with a 1 microfarad ceramic and is insensitive to ESR, which is one of the reasons for choosing this part over a bipolar regulator.

What is the difference between the DRB and DCQ bodies? The DRB is a 3 mm by 3 mm WSON on a large reel, and the DCQ is a SOT-223 in a tube. The silicon is the same and the thermal performance is better on the WSON, but the SOT-223 is the one that can be hand soldered.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.