TPS73501DRVR
Product Specifications
TPS73501DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS73501DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS73501DRVR adjustable 500 mA regulator in the 2 mm body
The TPS73501DRVR is the adjustable member of the TPS735 family, a 500 mA regulator that runs from 2.7 V to 6.5 V, sets its output from 1.25 V to 6 V through an external divider, and draws 45 microamp of ground current. The DRV suffix is the six pin two millimetre square WSON, which is the small of the two bodies the family offers, the other being an eight pin three millimetre SON. Both bodies carry the same die, so the choice between them is thermal and mechanical rather than electrical.
The family is the mid point of this line: 500 mA at 280 mV of typical dropout, 68 dB of rejection at 1 kHz, 11 microvolt RMS of noise with a 10 nanofarad noise reduction capacitor, and 45 microsecond startup. It is the part to use when a rail needs more than the 250 mA of the TPS734 and less than the ampere class, which is the common case for a 3.3 V or 2.5 V digital rail on a small board.
Key parameters from the SBVS087M document
| Input range | 2.7 V to 6.5 V, minimum also set by output plus dropout |
| Output | Adjustable 1.25 V to 6 V on a 1.208 V reference, window 1.196 V to 1.220 V |
| Current | 500 mA continuous |
| Accuracy | 2 percent over load, line and temperature for outputs above 2.2 V, 3 percent below |
| Dropout | 280 mV typical, 500 mV maximum at 500 mA |
| Ground current | 45 microamp typical, 65 microamp maximum |
| Shutdown current | 0.15 microamp typical, 1 microamp maximum |
| Rejection | 66 dB at 100 Hz, 68 dB at 1 kHz, 44 dB at 10 kHz, 22 dB at 100 kHz |
| Noise | 11 microvolt RMS with 10 nanofarad on the noise reduction pin, 95 microvolt RMS without it |
| Lockout | 1.9 V to 2.65 V rising with 70 mV of hysteresis |
| Package | DRV six pin WSON, 2 mm by 2 mm, marking SDR |
| Order code | TPS73501DRVR active, 3000 pieces on a large reel, moisture level 2 with a one year floor life on the DRB row |
Setting the output is where the errors come from
The reference is 1.208 V with a window of 1.196 V to 1.220 V, which is plus or minus 1 percent before any resistor is added. The published accuracy of 2 percent over temperature assumes 1 percent resistors; a divider built from 5 percent parts doubles the error and can push a 3.3 V rail outside the tolerance of the load. Where accuracy matters, the fixed member of the family is the better answer because the trim happens inside the package.
The noise reduction pin changes the noise by a factor of eight, from 95 microvolt RMS to 11 microvolt RMS with 10 nanofarad. That is a large change for one capacitor, and it also improves the rejection at low frequency. On a rail that feeds a phase locked loop or a data converter reference, the capacitor belongs on the board even where the rest of the board is minimal, and it costs one placement step.
Where this part fits
Industrial controllers, test instruments, telecom line cards and medical monitors use this family for a mid current analog or digital rail. Our substitution notes for the ampere class parts of this line are under power management cross reference, and the short list of questions we ask before a rail is changed is in PCBA quote checklist.
What to check before a purchase order
Check the dissipation against the body. The six pin WSON has a junction to ambient resistance that depends on the copper under it, and at 5 V in and 2.5 V out the part burns 1.25 W at full load, which no two millimetre body survives without a thermal pad tied to a plane. The eight pin SON in the same family is the correct choice for that operating point.
Check the divider current against the ground current budget. A divider of 100 kiloohm draws 12 microamp at a 1.2 V reference, which is small against 45 microamp, while a divider of 10 kiloohm draws 120 microamp and trebles the standby current of the rail. The divider has to be chosen with the same care as the regulator.
Questions that come up on this part
Does the output stay in regulation with no load? Yes, and the ground current figure of 45 microamp is quoted at no load. The part does not need a minimum load resistor.
What happens when the input falls below the lockout? The output turns off cleanly at the falling threshold and comes back when the input rises above the upper threshold, with 70 mV of hysteresis separating the two points, so a slow input ramp does not produce a burst of on and off cycles.