TPS73250DBVR
Product Specifications
TPS73250DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS73250DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS73250DBVR: 5.0 V fixed, 250 mA NMOS low dropout regulator, capacitor free, SOT-23-5
TPS73250DBVR is a fixed 5.0 V linear regulator that uses an NMOS pass element in a voltage follower, so it stays stable with no output capacitor at all and blocks reverse current when the output is above the input in a SOT-23-5 body of 5 pins. The input range is 1.7 V to 5.5 V and the dropout is 40 mV typical at 250 mA, which is what an NMOS follower with a charge pump achieves. Ground pin current is about 400 microamp at 10 mA and does not climb much with load, so the part does not lose efficiency at high current the way a PNP regulator does. Noise is 30 microvolt rms and rejection is 58 dB at 100 Hz.
Order code and package
| TPS73250DBVR | Active, SOT-23 (DBV) body, 5 pins, 3000 pieces on a large reel, marking T41 |
| TPS73250DBVR.A | Active, same body and same 3000 piece reel, material row at MSL Level-1-260C-UNLIM |
| TPS73250DBVT | Active, the same silicon in the SOT-223 (DCQ) body with 250 pieces on a small reel and a different marking |
| TPS73201 | the adjustable member with a 1.2 V reference, same bodies |
| Temperature range | minus 40 to 125 degrees junction |
Electrical parameters that decide the application
| Input voltage | 1.7 V to 5.5 V |
| Output voltage | 5.0 V fixed on this string, 1.2 V reference and adjustable on the 73201 |
| Output current | 250 mA maximum |
| Dropout | 40 mV typical at 250 mA, with 150 mV printed as the limit in the electrical table |
| Ground pin current | 400 microamp typical at 10 mA, 650 microamp at 250 mA |
| Current limit | 425 mA typical, 250 mA minimum, 600 mA maximum |
| Short circuit current | 300 mA with the output at zero |
| Noise and rejection | 30 microvolt rms, 58 dB at 100 Hz and 37 dB at 10 kHz |
Family variants and how they differ
| TPS73250 | 5.0 V fixed, the string on this page |
| TPS73201 | adjustable from a 1.2 V reference, same silicon, needs a divider |
| TPS732 | the family covers fixed outputs from 1.8 V to 5 V in the same bodies |
| Package choice | SOT-23-5 for a 3000 piece reel, SOT-223 for a 250 piece reel and better thermal path |
| Reverse current | 0.1 microamp typical leakage when the output is held above the input and the device is off |
Points to check before this part goes on a BOM
No output capacitor is a real feature and a real risk. The NMOS follower is stable with any output capacitor or with none, which removes a part from the bill of materials and removes the bias derating question. The risk is a load that switches fast: without any output capacitance the transient is handled entirely by the loop bandwidth, and a 10 microamp to 200 mA step produces a much larger dip than the same board with 1 microfarad fitted. A capacitor is optional, not forbidden, and most boards should fit one.
Forty millivolts of dropout is the headline and 150 mV is the budget. The typical number is measured at 250 mA with a fresh part at room temperature. The electrical table prints a 150 mV limit, and dropout grows at cold temperature and at the bottom of the current limit window. A 5 V rail fed from a 5.5 V input has 500 mV to spare and is comfortable; a rail fed from 5.2 V has 200 mV and is not.
The 5.5 V maximum input means this part cannot post regulate a 12 V bus. It is a low voltage regulator for a 5 V or 3.3 V system, not an industrial wide input part. A 5 V input with a 10 per cent tolerance reaches 5.5 V exactly, so there is no surge margin, and the 5.0 V output then has no headroom at all. Any board with a 5 V input and a 5 V output needs to look at the tolerance stack before it looks at the part.
Reverse current blocking is why this part survives a two supply board. When the output is held above the input, an ordinary LDO conducts through its body diode and charges the input rail, which can back feed a whole system. This part blocks that, with 0.1 microamp of leakage, which is what a battery backed rail needs. The feature is invisible in normal operation and decisive when a board has a charger and a battery on the same node.
Ground pin current is nearly flat, and that changes the efficiency sum. A PNP regulator carries a ground current that grows with load and can double the loss at high current. Here the ground current is 400 microamp at 10 mA and 650 microamp at 250 mA, so at 250 mA the total loss is the dropout times the load plus the ground current times the input, and the second term is small. A 5 V to 3.3 V rail at 200 mA therefore runs cool in a five pin body.
The current limit is 425 mA typical with a 1.7 times spread. The published window runs from 250 mA to 600 mA, and the short circuit current is 300 mA. A load that draws 300 mA on a 250 mA part sits above the rating and inside the limit, so it runs hot rather than tripping. The protection is there for a fault, not for a load that is simply too big.
Noise of 30 microvolt rms is low enough for an analogue front end and not low enough for a reference. A 12 bit converter with a 3.3 V reference has a step of about 800 microvolt, so 30 microvolt of regulator noise sits well below one bit. A 16 bit converter at the same reference has a step of 50 microvolt and the regulator noise starts to matter, which is where a filtered supply or a dedicated reference comes in.
The marking is T41 and it appears on several strings. Five pin bodies from this family carry similar codes, so a board that reads the marking to identify the fitted part can confuse a 3.3 V member with a 5 V member. For incoming inspection the reel label and the purchase order string are the reliable identifiers, and the marking is only a cross check.
Two bodies with different reels serve different builds. The SOT-23 ships 3000 pieces on a 180 mm reel and the SOT-223 ships 250 on a small reel with a much better thermal path. A board that dissipates more than about 300 mW should be on the larger body, and the decision has to be made before the board is laid out, not at the purchase order.
The enable pin is not a shutdown in the usual sense. Pulling enable low turns the pass element off, and the output then floats unless a load pulls it down. The shutdown current is specified with the output at or below the input, so a board that holds the output up from elsewhere while the regulator is disabled sits outside that condition and the leakage becomes the reverse blocking number instead.
What to confirm before this part goes on a purchase order
Give the input voltage with its tolerance and the output current. Dropout at 250 mA is the number that decides whether a 5 V to 5 V rail works, and a quote that names only the output voltage cannot be checked.
Say whether an output capacitor is fitted. The part does not require one, and the transient response of a board without one is a different product from the same part number with one fitted.
Where this order code fits
It post regulates a 5 V rail down to 3.3 V or holds a 5 V rail for an analogue section on a board that also has a battery or a second supply on the same node. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Can it be used with no output capacitor at all? Yes, that is the point of the NMOS follower topology. The loop is stable with any capacitor value or none, which is useful when the load is close to the regulator and the board has no room. Load transient response is then set by the loop alone, so a fast load step produces a larger dip than the same board with a capacitor fitted.
What happens if the input drops below the output? The pass element blocks and the leakage is about 0.1 microamp, so the output is not discharged into the input. That is what allows a battery or a second supply to hold the rail up while the regulator input collapses, without the regulator loading the surviving rail.
Is the 5.0 V output accurate enough to replace a reference? No. The output tolerance is a regulator tolerance, not a reference tolerance, and the part is specified over line, load and temperature as a supply. A converter that needs a defined reference uses a reference, and this regulator powers the rest of the board around it.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.