TPS6590378ZWSR
Product Specifications
TPS6590378ZWSR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS6590378ZWSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS6590378ZWSR power management unit with seven converters and seven regulators
The TPS6590378ZWSR is a power management unit for a processor based product: seven step down converters, seven low dropout regulators, a sixteen megahertz crystal oscillator, a thirty two kilohertz RC oscillator, a real time clock with alarm wake up, a twelve bit sigma delta analogue to digital converter and an OTP programmed power sequence, in a 169 pin nFBGA of 12 mm by 12 mm on a 0.8 mm pitch. The system voltage range is 3.135 V to 5.25 V.
The converter list is built around a processor core: one 0.7 V to 1.65 V rail at 6 A in a dual phase arrangement with digital voltage scaling, one 0.7 V to 1.65 V at 4 A also dual phase with scaling, one 0.7 V to 3.3 V at 3 A that can be combined with the 6 A rail into a 9 A triple phase regulator, two 0.7 V to 3.3 V at 2 A, and two 0.7 V to 3.3 V at 1 A. Steps are 10 mV in the low range and 10 or 20 mV above it, and all but the 1 A converters report their output current.
The regulator list covers two 300 mA and two 200 mA LDOs from a pre regulated supply, one 50 mA LDO, a 100 mA USB LDO, one low noise 100 mA LDO and two internal rails. The analogue converter has three external channels and six internal ones for self monitoring, and the thermal block provides a warning plus a shutdown.
Key parameters from the SLIS165G document
| System voltage | 3.135 V to 5.25 V on VCC1 and the converter inputs |
| Core converter | 0.7 V to 1.65 V at 6 A, dual phase, digital voltage scaling, 10 mV steps |
| Second converter | 0.7 V to 1.65 V at 4 A, dual phase, digital voltage scaling |
| Third converter | 0.7 V to 3.3 V at 3 A, combinable with the 6 A rail into a 9 A triple phase regulator |
| Remaining converters | Two at 2 A and two at 1 A, 0.7 V to 3.3 V, 10 or 20 mV steps |
| Regulators | Two 300 mA, two 200 mA, one 50 mA, a 100 mA USB LDO and a low noise 100 mA LDO |
| Light load | Eco mode up to 5 mA with 15 microamps of quiescent current |
| Sensing | Differential remote sense on the dual and triple phase rails, current measurement on all but the 1 A parts |
| Monitoring | 12 bit sigma delta converter with three external and six internal channels, thermal warning and shutdown |
| Package | ZWS 169 pin nFBGA of 12 mm by 12 mm, 0.8 mm pitch, 1000 pieces on a large reel, moisture level 3 |
The order image letter and the status of the family
The trailing letter before the body code selects the OTP image, which holds the rail voltages, the power up and power down order and the sleep state configuration. The addendum prints images 6 and 7 in the ZWS body at 1000 pieces on a large reel and 250 on a small one, and every printed row for this body carries the status not recommended for new builds. The catalogue code on this page carries image 8, which is not among the printed rows, so the image has to come from the vendor configuration record or from a previous purchase rather than from the addendum alone.
That combination is a purchasing fact rather than an electrical one: a part that is not recommended for new builds still has to be bought for an existing product, and the last time buy planning for it starts from the addendum status rather than from a distributor note.
Where this part fits
Processor modules, industrial single board computers, test equipment and any product that needs a wide rail list and a fixed sequence from a 5 V supply. Obsolescence planning for this class is filed under component obsolescence management and last time buy and LTB planning.
What to check before a purchase order
Check the image letter and the body code together. Two parts from this family with different image letters are the same silicon and different products, and the addendum does not decode the rails in words, so the image has to be matched against the vendor configuration file for the board.
Check the status before quoting a new build. The printed rows carry not recommended for new builds, which means a new product should plan a replacement rather than a second source of the same code. The reel and date practice for a long lived part is in date code management.
Questions that come up on this part
Can the 6 A and 4 A rails be combined? The 3 A rail can be combined with the 6 A rail into a 9 A triple phase regulator with voltage scaling, which is the arrangement the vendor documents for a high current core.
Does the part need an external crystal? It needs a 16 MHz crystal for the main clock and can use the internal 32 kHz RC for the real time clock, so a product that does not keep time can omit the second crystal.