Contact Us

TPS65400QRGZRQ1

Brand: Texas Instruments
Texas Instruments TPS65400QRGZRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65400QRGZRQ1 — Power Management & Signal Chain | Superb Automation

TPS65400QRGZRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65400QRGZRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65400QRGZRQ1: a four output automotive power management unit with PMBus control in a 7 mm by 7 mm body

TPS65400QRGZRQ1 is an automotive power management unit with two 4 A and two 2 A synchronous buck converters, a digital reference and an I2C interface in a VQFN (RGZ) body of 48 pins. It takes 4.5 V to 18 V in and produces four rails from one package: two switchers rated 4 A and two rated 2 A, each with its own resistor set switching frequency from 275 kHz to 2.2 MHz, its own current limit choice and its own enable pin for sequencing. The output voltage is set by a divider against a reference that runs from 0.6 V to 1.87 V in 10 mV steps over the bus, so a rail can be trimmed at test time instead of at the resistor. Quiescent current is 8 mA typical, overvoltage protection trips at 111 per cent of the reference and undervoltage at 92 per cent, and the part is AEC-Q100 grade 1.

Order code and package

TPS65400QRGZRQ1VQFN body of 48 pins measuring 7.00 mm by 7.00 mm on a 0.5 mm pitch, 2500 pieces on a large reel, moisture level 3 at 260 C with 168 hours of floor life, marking TPS65400Q, active status in the addendum dated 12 August 2026
Switchers 1 and 24 A each, with current sharing available between them so a single 8 A rail can be built from the pair when the inductors are chosen for it
Switchers 3 and 42 A each, with current sharing between them in the same way, and with a lower switch resistance than the larger pair
Referenceone digital reference per switcher, 0.6 V to 1.87 V in 10 mV steps, written over the bus and held in the on chip memory
Sequencinga precision enable pin per switcher plus a soft start capacitor per switcher, so the order of the rails is a resistor and capacitor choice rather than a firmware loop
Package48 pins on a 7 mm by 7 mm body with an exposed pad, and the pad carries both the ground return and the heat

Electrical parameters that decide the application

Input voltage4.5 V to 18 V, which covers a 5 V, 12 V or 15 V intermediate bus without a pre-regulator
Output voltage0.6 V to 90 per cent of the input on each switcher, set by a divider against the programmable reference
Output current4 A maximum on switchers 1 and 2 and 2 A maximum on switchers 3 and 4, with current sharing available inside each pair
Switch resistance42 milliohm on the low side of the 4 A pair and 120 milliohm high side with 90 milliohm low side on the 2 A pair, all typical figures at 25 C
Current limitselectable per switcher at 1 A, 2 A or 3 A on the 2 A pair, with a plus or minus 25 per cent accuracy against the selected value
Switching frequency275 kHz to 2.2 MHz per switcher, set by a resistor from 165 kilohm, with a plus or minus 10 per cent accuracy and a clock output for synchronising other parts
Phase controleach switcher can be phase shifted against the others, which lowers the input ripple and the size of the input capacitor
Minimum on time80 ns, and minimum off time 150 ns, which together set the duty cycle range and therefore the maximum step down ratio at a given frequency
Quiescent current8 mA typical and 27 mA maximum with the part enabled, no load and all four switchers not switching, which is high for a battery product and normal for a bus converter
Undervoltage lockoutthe input turns on between 4.25 V and 4.48 V and turns off between 3.4 V and 3.75 V, so a 5 V bus with a dip has a defined behaviour
Overvoltage protection111 per cent of the reference on the rising edge and 104 per cent on the falling edge, with the fault latched and the power good output dropped
Undervoltage protection92 per cent of the reference on the way down and 83 per cent on the way back up, with the power good output following the fault
Thermal shutdown160 C on the rising edge with 20 C of hysteresis, which is a protection for a 7 mm body dissipating several watts
InterfacePMBus compatible I2C with a resistor selected address, a clock sync input, a clock output and an alert output

What the four switchers share and what they do not

TPS65400-Q1the four output unit covered by this order code, two 4 A and two 2 A switchers with a PMBus interface, 48 pins on 7 mm by 7 mm
Switcher pairsswitchers 1 and 2 share current when the inductors are chosen for it, and so do switchers 3 and 4, which is how a single larger rail is built from the package
Reference0.6 V to 1.87 V in 10 mV steps over the bus, so the divider sets the coarse value and the bus trims the rest
Sequencinga precision enable and a soft start capacitor per switcher, so the rail order is set by parts rather than by firmware
Phaseeach switcher can be shifted against the others, which spreads the input ripple and lowers the input capacitor requirement
Fault reportingovervoltage, undervoltage and current limit are reported per switcher over the bus, which is what makes a field return diagnosable
Thermal160 C shutdown with 20 C of hysteresis, in a package that can dissipate several watts on the exposed pad

Points to check before this part goes on a BOM

The reference is digital, so the divider is the coarse setting and the bus is the fine one. A rail is set to roughly the right voltage by two resistors and then trimmed in 10 mV steps over the bus. That is the property that makes the part useful on a board that feeds several processors with slightly different core voltages from one bill of materials.

The current limit is a choice, not a fixed protection. Selecting 1 A, 2 A or 3 A lets the inductor be sized to the rail rather than to the switch. The plus or minus 25 per cent accuracy means a 1 A setting can trip anywhere from 0.75 A to 1.25 A, so a load that sits near the selected value needs margin.

Quiescent current of 8 mA follows from what sits inside the package. Four switchers, four references and a digital block all draw standing current. A product that has to sit in a low power state for weeks cannot leave this part enabled, so the enable pins and the sequencing have to include a full shutdown path.

The minimum off time limits the step down ratio. At 2.2 MHz the 150 ns off time means the part cannot hold a very low output from an 18 V input. A rail that needs 0.6 V from 18 V has to run at a lower frequency, and the frequency is set per switcher for exactly that reason.

Phase shift is an input capacitor decision. Running four switchers in phase adds their ripple currents at the input. Shifting them spreads the pulses and lowers the RMS current the input capacitor has to carry, which is often what makes a small ceramic input bank viable.

Moisture level 3 means the reel has a clock on it. 168 hours of floor life at 260 C, after which the parts have to be baked before a reflow. A line that opens a reel for a pilot and comes back to it a month later has to plan for that bake.

Why one package with four rails is used instead of four parts

A board that needs a core rail, an input output rail, an analog rail and a peripheral rail from one 12 V bus would otherwise carry four converters, four sets of feedback parts and four soft start networks. Putting them in one body shares the input capacitor, the reference and the sequencing, and it removes the rail order question from the firmware.

The cost is that a fault in one switcher takes the package down, and that the thermal budget is shared. The part is used where the four loads are known and stable, and where the board has room for the exposed pad the 7 mm body needs.

What the bus changes at production test

A rail that is trimmed over the bus can be brought to its final value after the board is assembled, which removes the resistor tolerance from the yield equation. The trim value lives in the on chip memory, so a board that is retested a year later still comes up at the value that was written.

The same interface reports the fault flags, which is what makes a field return diagnosable. A board that comes back with a dead rail can be read for an overvoltage or undervoltage event before anything is unsoldered.

Where this order code fits

an automotive base station, a gateway or an industrial controller that needs four sequenced rails from one 12 V bus Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How many rails does this part produce? Four. Two switchers are rated 4 A and two are rated 2 A, and each pair can share current to build a single larger rail when the inductors are chosen for it.

How is the output voltage set? By a divider against a reference that is programmable from 0.6 V to 1.87 V in 10 mV steps over the bus. The divider sets the approximate value and the bus trims it, which takes the resistor tolerance out of the final rail.

Does it need an external clock? No, each switcher has its own resistor set frequency from 275 kHz to 2.2 MHz. A clock input and a clock output are provided for systems that want several parts running at one frequency.

What happens if one output is overloaded? The current limit for that switcher trips at the selected 1 A, 2 A or 3 A level with plus or minus 25 per cent accuracy, and the fault is reported over the bus. The other three rails keep running, which is the reason the limits are per switcher.

Is the part automotive qualified? Yes. It is AEC-Q100 grade 1, specified over minus 40 C to 125 C ambient, with the human body and charged device ESD classifications named in the document.

What packing does the R suffix arrive in? 2500 pieces on a large reel at moisture level 3, so the reel has 168 hours of floor life at 260 C after it is opened and needs baking before a second reflow.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.