TPS65233RTER
Product Specifications
TPS65233RTER
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS65233RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS65233RTER: LNB supply and control regulator for satellite receivers
TPS65233RTER is a satellite front end regulator that produces the 13 V and 18 V LNB rail and the 22 kHz control tone in a QFN (RTE) body of 16 pins. It integrates a 500 kHz boost converter with a 120 milliohm switch, a low noise linear stage with push pull output, a tone generator and a full diagnostic set that is read back over I2C, in a 3 mm by 3 mm body.
Order code and package
| Order code read out | TPS65233 RTE R: family, RTE 16 pin QFN 3 mm by 3 mm, R tape and reel |
| Package | QFN (RTE), 16 pins including the thermal pad, 3.00 mm by 3.00 mm |
| Carrier | 2500 pieces on a reel |
| Operating temperature | minus 40 to plus 85 degrees Celsius |
| Supply options | 5 V and 12 V input bus, the part is specified for both |
| Interface | I2C for voltage selection, current limit and diagnostics, plus a dedicated enable pin so the part can run without a bus |
| Compatibility | DiSEqC 1.x tone and voltage signalling, the standard used across satellite receiver systems |
| Thermal pad | pin 16 on the underside, tied to the boost converter power ground, and it has to be soldered to a copper pour |
Electrical parameters that decide the application
| Output voltage | 13 V and 18 V, the two LNB polarisation rails, switched over I2C or by the tone path |
| Output current limit | up to 1000 mA, set by an external resistor and trimmed by I2C, plus or minus 10 percent accuracy |
| Boost switch | 120 milliohm internal MOSFET at 500 kHz, which is what keeps the inductor small |
| Linear stage dropout | 0.8 V, the number that decides how much headroom the boost rail needs above 18 V |
| Tone generator | 22 kHz, internal and accurate, or driven from an external pin |
| Soft start | adjustable, and so is the 13 V to 18 V transition time |
| Diagnostics | output voltage level, input supply undervoltage, tone output state and cable disconnect, all readable over I2C |
| Protection | dynamic short circuit protection on the LNB output, thermal shutdown, input undervoltage lockout |
| Input bus | 5 V or 12 V, both specified, with the boost duty cycle following from the choice |
Family variants and how they differ
| TPS65233 | the I2C version on this page, with the full diagnostic set |
| Enable pin variant | the dedicated enable input covers receivers that have no bus to the front end |
| Tone source | internal generator or external pin, which matters when the demodulator already produces the 22 kHz signal |
| Current limit | resistor set with I2C trim, so one board can serve several receiver models |
| Package | the 16 pin RTE is the only body offered, so a socket change is not an option |
Points to check before this part goes on a BOM
The 0.8 V dropout is the boost rail budget. To hold 18 V at the output through the linear stage, the boost converter has to deliver at least 18.8 V, and that number moves with load and temperature. A board that sets the boost target at 19 V leaves 200 mV, which is thin once the current limit resistor tolerance and the cable drop are counted.
The current limit is a resistor plus an I2C trim, and both carry tolerance. The published accuracy is plus or minus 10 percent, so a 1000 mA setting can pass 1100 mA before it folds back. A receiver built for a 500 mA LNB should not be trimmed to 1000 mA just because the part allows it, since the coax and the connector see that current too.
Dynamic short circuit protection is not a latch. The part reacts to a short on the LNB line and recovers, which is the right behaviour for a dish that gets wet, but it also means a persistent fault produces a retry cycle rather than a clean shutdown. Service diagnostics should read the I2C fault registers rather than infer the fault from a dead rail.
The 22 kHz tone can come from two places. Using the internal generator gives a clean signal at zero load, which the external pin route does not guarantee if the driving source is weak. Mixing the two in one product, internal for one tuner and external for another, is a common source of DiSEqC switching faults in multi tuner receivers.
The 5 V and 12 V bus options change the boost duty cycle and the loss. A 5 V input running up to 19 V draws roughly four times the input current of a 12 V input for the same output power, so the input capacitor and the inductor rating have to be chosen for the bus the board actually has.
The inductor and the input capacitor carry the whole LNB current. At 5 V in and 20 V out the input current is about four times the output, so a 500 mA load draws 2 A from the 5 V rail plus the boost loss. An inductor chosen for 1 A saturation will run hot and then saturate, and the failure looks like a current limit fault at the receiver.
The thermal pad is the only heat path. The 3 mm body has no leads to speak of, so the exposed pad under the die has to be soldered to a copper area with vias to the ground plane. A board that treats the pad as a mechanical feature will run the boost switch hot and shorten the part's life, and the symptom is a receiver that works on the bench and fails in a warm cabinet.
Diagnostics exist so that a receiver can tell a customer what failed. Output voltage level, input undervoltage, tone state and cable disconnect are all readable, which distinguishes a dish fault from a receiver fault without sending an engineer. Teams that leave those registers unread lose the main service advantage of the I2C version.
Switching between 13 V and 18 V is a load step on the boost converter. The transition time is adjustable, and the reason to adjust it is that a fast transition produces an overshoot that a slow one does not. Receivers that report intermittent lock loss after a polarisation change usually have the transition set too fast for the output capacitance on the board.
Where this order code fits
These parts sit in set top boxes, integrated satellite televisions, PC satellite cards and multi switch boxes, where a single rail has to serve a dish mounted LNB over a long coax run with tone signalling on the same wire. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does the part support DiSEqC 1.x fully? It generates the 22 kHz tone and switches the 13 V and 18 V rails, which is what DiSEqC 1.x needs from the supply side. The command encoding belongs to the demodulator, not to this regulator.
Can I use it with a 5 V only board? Yes, the 5 V bus is specified, but the input current for the same output power is much higher than on 12 V, so the inductor and the input capacitor have to be sized for that case.
What is the failure mode on a shorted coax? The part folds back and retries rather than latching off. That keeps a wet connector from killing the receiver, and the fault registers record the event for service.
Does the part need a microcontroller? No. The dedicated enable pin runs the regulator without a bus, and the I2C interface is only needed for voltage selection, current trim and diagnostics.
What sets the 22 kHz tone amplitude? The internal generator superimposes the tone on the output, and it holds the amplitude even at zero load, which an external injection path does not always do.
How fast can the rail switch between 13 V and 18 V? The transition time is set by an external component and by I2C. Faster switching stresses the boost converter and the coax, so the setting should follow the receiver's tuning requirements.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.