TPS65218D0PHPR
Product Specifications
TPS65218D0PHPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS65218D0PHPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS65218D0PHPR: a 48 pin power management IC that sequences six rails for a Cortex-A8 or A9 processor and a small FPGA
TPS65218D0PHPR is a single chip power management IC for a processor rail set, built around three step down converters, one buck boost, two backup domain converters, one LDO and three load switches in a HTQFP (PHP) body of 48 pins. The three main converters each carry 1.8 A of switch current, the buck boost carries 1.6 A, the two backup converters can run from a coin cell, and the I2C port at address 0x24 lets the processor read and change every rail while the system is running. The device is characterised from minus 40 C to 105 C.
Order code and package
| TPS65218D0PHPR | HTQFP (PHP) body, 48 pins, 7.00 mm by 7.00 mm, the ordering string this page is built around, packed on the 1000 piece large reel that the addendum lists for the PHP rows |
| TPS65218B1PHPR | the string the addendum actually carries on the same body, marked NRND, 1000 pieces on a large reel, nickel palladium gold finish, moisture level 3 at 260 C for 168 hours, marking T65218B1 |
| TPS65218B101PHPR | the B101 option on the same body and the same packing, marking 65218B101, and the only member whose supervisor offers the 200 mV hysteresis setting |
| TPS65218B1RSLR | the VQFN (RSL) body, 48 pins, 6.00 mm by 6.00 mm, 2500 pieces on a large reel, same die in a smaller footprint |
| Small reel rows | the PHPT and RSLT suffixes carry 250 pieces and are the strings a pilot build orders before the main release |
| Suffix rows | the addendum repeats most strings with an .A suffix, so packing and finish have to be read per row rather than taken from the suffix |
Electrical parameters that decide the application
| Input voltage | DCDC1, DCDC2, DCDC3 and DCDC4 run from 2.7 V to 5.5 V, LDO1 from 1.8 V to 5.5 V, the two backup converters from 2.2 V to 5.5 V, and the high voltage load switch LS3 from 1.8 V to 10 V |
| DCDC1 and DCDC2 | 1.1 V default, adjustable from 0.85 V to 1.675 V, 1.8 A of switch current, power save mode at light load and 100 per cent duty cycle for the lowest dropout |
| DCDC3 | 1.2 V default, adjustable from 0.9 V to 3.4 V, 1.8 A, the rail that usually feeds the processor core |
| DCDC4 | a buck boost at 3.3 V default, adjustable from 1.175 V to 3.4 V, 1.6 A, which holds its output when the input falls below the setting |
| DCDC5 and DCDC6 | 1 V and 1.8 V fixed outputs for the backup domain, supplied either from the main rail or from a coin cell battery |
| LDO1 | 1.8 V default, adjustable from 0.9 V to 3.4 V, 400 mA, with active output discharge when the rail is disabled |
| LS1 | a low voltage load switch from 1.2 V to 3.6 V with a 350 mA current limit and 110 milliohm maximum switch impedance at 1.35 V |
| LS2 and LS3 | load switches with a selectable 100 mA or 500 mA limit, LS2 covering 4 V to 5.5 V and LS3 covering the higher rail up to 10 V |
| Supervisor | DCDC1 and DCDC2 are monitored to plus or minus 4 per cent, DCDC3, DCDC4 and LDO1 to plus or minus 5 per cent, with separate power good outputs for the main rails and the backup supply |
| I2C port | fixed address 0x24 at 400 kHz, which is how the processor sets voltages, reads status and reaches the configuration registers |
| Protection | undervoltage lockout, an always on push button monitor, overtemperature warning and thermal shutdown |
| Temperature | minus 40 C to 105 C operating, which is where the industrial applications named in the document sit |
Family variants and how they differ
| D0 and B1 | the silicon revision register names revision 4.0 as D0, while the addendum dated 8 January 2026 carries only B1 and B101 strings and marks every one of them NRND |
| B101 difference | the B101 option resets CONFIG2 to 0x80 instead of 0xC0 and is the member that offers the 200 mV supervisor hysteresis setting |
| PHP and RSL | the same die in a 7.00 mm HTQFP and a 6.00 mm VQFN, so the land pattern has to follow the body named on the order string |
| Reel size | 1000 or 2500 pieces on the large reel depending on body, 250 on the small reel, which decides whether a line can run a pilot build without re-reeling |
| Finish | nickel palladium gold on the PHP rows at moisture level 3, so the floor life clock starts when the bag is opened |
Points to check before this part goes on a BOM
The string on this page does not appear in the addendum. The addendum dated 8 January 2026 lists only B1 and B101 rows and marks every one of them NRND, so the exact string should be confirmed against a written offer before it goes on a BOM.
Two bodies share one die. The PHP body is 7.00 mm square and the RSL body is 6.00 mm square, and a board written for one will not take the other without a new land pattern and a new stencil aperture set.
The backup converters sit on their own input. They accept 2.2 V to 5.5 V and can be fed from a coin cell, which is what keeps the real time clock and the retention domain alive when the main rail is down.
The I2C address is fixed at 0x24. Two of these devices cannot share one bus without an external switch, and the address is not one of the settings a register write can move.
Power good is split in two. One output covers the main rails and one covers the backup supply, so a sequencer can tell a main rail failure from a dead coin cell instead of treating both as the same fault.
How the rails are usually ordered
The sequence in most systems follows the processor datasheet rather than the PMIC: DCDC1 and DCDC2 come up first because they feed the I/O ring, DCDC3 follows for the core, and DCDC4 and LDO1 come last because they feed peripherals that must not be live before the core is stable. The push button monitor and the power good outputs are what hold that order in place.
The three load switches are often left unused on a first build and picked up on the second, when the board has to isolate a cellular module or a card slot. They are independent of the converter sequence, which is why they appear late in a programme rather than at the start.
Where this order code fits
The part is built for a processor that needs six rails in a known order, which is the shape of a handheld instrument, an industrial panel or a point of sale terminal. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is this string still active? The addendum on the current document carries B1 and B101 strings only, all marked NRND. A requirement for the D0 string is met from stock or from a franchised source, and the offer states the date code and the country of origin.
Can it run from a 5 V adapter as well as a battery? Yes. The four main converters accept 2.7 V to 5.5 V, so a regulated 5 V adapter and a single cell lithium battery both fall inside the window. The backup converters accept 2.2 V to 5.5 V and can be fed from a coin cell.
What has to be checked before a substitute goes on the board? The body, the reel size and the register defaults. The B101 resets CONFIG2 to a different value, and a board that relies on the reset state of that register will boot with a different supervisor behaviour.
Do you hold this part? SUPERB holds and sources the family for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.