Contact Us

TPS65131TRGERQ1

Brand: Texas Instruments
Texas Instruments TPS65131TRGERQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65131TRGERQ1 — Power Management & Signal Chain | Superb Automation

TPS65131TRGERQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65131TRGERQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65131TRGERQ1: a dual output converter that makes plus and minus 15 V from a 3.3 V or 5 V rail

TPS65131TRGERQ1 is an automotive dual output dc to dc converter with a boost stage for the positive rail and an inverting stage for the negative one in a QFN (RGE) body of 24 pins. It takes 2.7 V to 5.5 V of input and produces a positive rail up to 15 V and a negative rail down to minus 15 V, each with typically 200 mA depending on the ratio between input and output. Both switches are rated at 2 A of typical current limit, conversion efficiency reaches 91 per cent on the positive rail and 85 per cent on the negative one, and the total quiescent current is 500 microamps with 0.2 microamps in shutdown. The QFN-24 body has a thermal pad and wettable flanks, and the part is qualified to AEC-Q100 grade 2 for minus 40 C to 105 C ambient with the electrical table tested to 125 C junction.

Order code and package

TPS65131TRGERQ1the automotive member with both converters in one body, 24 pins on 4 mm by 4 mm with wettable flanks, which is the version an automotive module orders
TPS65130the commercial sibling with the same topology and a lower switch current limit, so the two are not interchangeable on a rail that needs the full 200 mA
Positive raila boost converter with a 2 A typical switch limit, an adjustable output up to 15 V, and a fixed 1.6 MHz class switching frequency that keeps the inductor small
Negative railan inverting converter with its own 2 A switch limit, adjustable down to minus 15 V, sharing the same clock so the two rails do not beat against each other
Power save modepulse skipping at light load, which is what brings the quiescent current down on a rail that idles rather than a rail that drives a display
Enable pinsseparate enables for the two converters, so the negative rail can come up after the positive one, which is the order an amplifier or a display bias needs

Electrical parameters that decide the application

Input voltage2.7 V to 5.5 V, which covers a single lithium cell, a 3.3 V bus and a 5 V bus without a pre-regulator
Output voltagepositive rail adjustable up to 15 V and negative rail down to minus 15 V, both set by external dividers
Output currenttypically 200 mA on each rail, with the real figure set by the ratio between input and output voltage and by the inductor chosen
Switch current limit2 A typical on both the boost and the inverter main switches, which is the figure that decides the inductor saturation rating
Efficiencyup to 91 per cent on the positive rail and up to 85 per cent on the negative rail, quoted at the ratios shown in the typical curves
Switching frequencyfixed frequency PWM control with an internal clock, which keeps the ripple predictable and the inductor value small
Quiescent current500 microamps typical for the whole device, which is a working figure rather than a standby figure
Shutdown current0.2 microamps typical, which is what a module in a parked vehicle actually draws from the battery line
Referencean internal reference sets both outputs through external dividers, so the accuracy of each rail is the reference plus the divider tolerance
Protectioncycle by cycle current limit on both switches, thermal shutdown, and an undervoltage lockout that keeps the part off until the input is usable
QualificationAEC-Q100 grade 2 for minus 40 C to 105 C ambient, with the electrical characteristics tested over minus 40 C to 125 C junction
BodyQFN-24 of 4 mm by 4 mm with a thermal pad and wettable flanks, which is what allows an automated inspection of the solder joint on an automotive board

How the two rails are built and where the family differs

TPS65131TRGERQ1this order code, the automotive member with both converters in a QFN-24 of 4 mm by 4 mm with wettable flanks
TPS65130the commercial sibling with a lower switch current limit, same topology and a different ceiling on the load
Positive raila boost stage with a 2 A typical switch limit and an adjustable output up to 15 V
Negative railan inverting stage with its own switch and its own inductor, adjustable to minus 15 V, sharing the clock with the boost
Enablesseparate enable pins, so the positive rail can come up before the negative one, which is the order an amplifier bias needs
Shutdown current0.2 microamps, against 500 microamps of quiescent current while both rails are up
QualificationAEC-Q100 grade 2 for minus 40 C to 105 C ambient with the electrical table tested to 125 C junction

Points to check before this part goes on a BOM

Two rails from one body is a board area decision. A positive boost and a negative inverter built from two separate controllers take two inductors, two sets of compensation and two footprints. This part shares a clock, a reference and a body, and the saving is real on a module that has to fit behind a display.

The negative rail is an inverting converter, not a charge pump. It has its own inductor and its own switch, so it can deliver real current at minus 15 V rather than the few milliamps a charge pump gives. That is what makes it usable for an amplifier or a sensor bias rather than only for a gate drive.

200 mA is a ratio dependent figure. The output current available on each rail falls as the ratio between input and output voltage grows, because the switch current limit is fixed at 2 A. A rail making 15 V from 3.3 V has less current available than one making 9 V from 5 V, and the curves in the document are the place to read it rather than the headline.

The two enables allow a rail order. An amplifier that needs its positive rail before its negative one, or a display that needs the opposite, is sequenced by the enable pins rather than by an external load switch. Sequencing in the wrong order can forward bias an internal junction and latch the part, which is why the order is stated in the document.

0.2 microamps of shutdown current is the automotive figure. A module that is off but still connected to the battery draws this current for weeks. The 500 microamp figure is what it draws while the rails are up, which is a completely different line in the budget.

The QFN body needs the thermal pad soldered. The pad is the only path from the die to the board, and a pad with voids under it runs the junction far above what the thermal table predicts. On a 4 mm body handling two converters, that is the failure mode that shows up as a part that works on the bench and fails in the enclosure.

Where a plus and minus 15 V pair comes from a 5 V bus

An operational amplifier front end, a sensor bias network or a display module often needs a symmetric supply and has only a 5 V or 3.3 V bus available. A pair of converters built from one body and one clock gives both rails without the beat frequency that two independent switching regulators produce, and the shared clock is what keeps the intermodulation out of the signal band.

On an automotive module the same part also has to survive the battery line. The input window stops at 5.5 V, so the converter sits behind a pre-regulator or a protection stage rather than on the battery directly, and the shutdown current of 0.2 microamps is what the module draws once that stage is off.

Reading the current capability honestly

The typical output current of 200 mA belongs to the ratios in the efficiency curves, not to every combination of input and output. The switch limit is 2 A in both converters, so the available output current falls as the step up ratio rises, and a calculation that assumes 200 mA at 15 V from 3 V of input is asking for more than the switch can deliver. The inductor saturation rating and the switch limit together set the ceiling.

Where this order code fits

a symmetric plus and minus 15 V supply for an amplifier or a sensor front end on a 5 V or 3.3 V bus, or a display bias in an automotive module Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can both rails deliver 200 mA at the same time? Not at every ratio. The 2 A switch limit is shared by the physics of each converter separately, and the available current on each rail falls as the step up ratio grows. The curves in the document give the figure for a specific input and output pair.

What input voltage does it need? 2.7 V to 5.5 V. A 3.3 V or 5 V bus is the normal case, and a single lithium cell is inside the window for most of its discharge.

Does it need two inductors? Yes, one for the boost stage and one for the inverter. They share a clock but not a magnetic component, and both have to be rated above the 2 A switch limit with margin for saturation.

Can the rails be sequenced? Yes, the two converters have separate enable pins, so the positive rail can be brought up before the negative one or the other way round, which is what an amplifier or a display bias needs.

What does the automotive qualification cover? AEC-Q100 grade 2, minus 40 C to 105 C ambient, with the electrical table tested from minus 40 C to 125 C junction and the body carrying wettable flanks for automated solder inspection.

How does SUPERB quote this part? Against the exact ordering string in the QFN-24 body, with the date code, the packing and the country of origin on the offer, because the commercial sibling is a different switch limit in a similar body.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.