Contact Us

TPS631010YBGR

Brand: Texas Instruments
Texas Instruments TPS631010YBGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS631010YBGR — Power Management & Signal Chain | Superb Automation

TPS631010YBGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS631010YBGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS631010YBGR: 1.5 A buck boost with adjustable output in a 1.8 mm by 0.9 mm chip scale body

TPS631010YBGR is a buck boost converter that holds its output steady while a single cell battery swings above and below the rail, using one small inductor and an 8 ball chip scale body in a DSBGA body of 8 pins. It takes 1.6 V to 5.5 V in, sets any output between 1.2 V and 5.5 V with two resistors, and switches at 2 MHz so the inductor can be a 1 uH chip part. The peak switch current is 3 A typical, which the document turns into 2 A of output at 3.3 V from 3 V in and 1.5 A from 2.7 V in. Quiescent current is 8 uA into the output and 0.15 uA into the input, and the body measures 1.803 mm by 0.905 mm.

Order code and package

TPS631010YBGR8 ball DSBGA (YBG), 1.803 mm by 0.905 mm, 3000 pieces on a large reel, tin silver copper balls, moisture level 1 unlimited, marking 1NS, minus 40 C to plus 125 C
TPS631011YBGRthe same converter with an active output discharge that pulls the rail down when the enable pin goes low, marking 1OM, same reel and same body
BallsVIN, LX1, LX2, VOUT, EN, MODE, FB and GND, with the two switch pins on opposite sides of the body for the inductor loop
Packingthe addendum prints one reel quantity for both strings, 3000 on a large reel, and no tube or small reel row exists for this body
Second row per codeeach string repeats with an .A suffix, and both rows carry the same quantity, so the suffix does not change the packing here

Electrical parameters that decide the application

Input voltage1.6 V to 5.5 V operating, 1.65 V minimum for start up, with a lockout between 1.5 V and 1.6 V rising and 1.4 V to 1.5 V falling
Output voltage1.2 V to 5.5 V adjustable through the feedback pin, with a 500 mV reference that is 1 per cent accurate
Output current2 A at 3.3 V from an input above 3 V, 1.5 A from an input above 2.7 V, and 1.0 V output supported in power save mode
Peak switch current2.6 A minimum, 3 A typical and 3.35 A maximum on the sourcing side, and minus 0.45 A to minus 0.7 A on the sinking side
Switching frequency2 MHz fixed, in buck, boost or the three cycle buck boost mode the part enters when input and output are within a few hundred millivolts
Quiescent current8 uA into the output and 0.15 uA into the input with no switching, and 0.5 uA total in shutdown
Switch resistance45 milliohm, 50 milliohm, 50 milliohm and 85 milliohm for the four internal switches at 3.8 V in and 0.2 A
Mode pinselects automatic power save or forced fixed frequency operation, and the part enters power save automatically as the load falls through 145 mA of peak current
Protectionovercurrent, output short circuit, output overvoltage and overtemperature, with a true shutdown that disconnects the load from the input
Output dischargeTPS631011 only, minus 67 mA with the enable pin low, which matters when the next stage cannot tolerate a rail that floats
Start upinternal soft start with ramp adoption, so the part can start into an output that is already pre biased

Which member and which mode

TPS631011adds the active output discharge, and is otherwise the same die, the same body and the same reel. The choice is made by what the load does when the rail collapses
TPS63101x familythe 1.5 A member in this document, while the wider family publishes higher current versions with a different peak switch rating
MODE pin highforced fixed frequency, which keeps the switching tone out of an audio or radio band at the cost of light load efficiency
MODE pin lowautomatic power save, which drops the switching frequency and the quiescent draw as the load falls
Three cycle modeentered when the input is close to the output, and the document states that the transition happens at a defined duty cycle so the part does not toggle between modes
Pre biased startsupported by the soft start ramp adoption, which is the reason a converter of this size can sit behind another regulator without a diode

Points to check before this part goes on a BOM

The output current rating is not one number. 2 A applies at 3.3 V out with an input above 3 V, and 1.5 A applies from 2.7 V in. Below that the part still runs but the deliverable current falls with the input, because the switch current limit of 3 A typical has to carry both the input and the output side of the conversion. A single cell battery that sags to 2.6 V under load will not deliver the 2 A that the front page suggests, and a board that sized its copper for 2 A finds out at the coldest corner of the battery curve.

The 1.6 V minimum input is a start up figure, not an operating figure. Start up needs 1.65 V, and the lockout sits between 1.5 V and 1.6 V rising with about 100 mV of hysteresis. A two cell alkaline pack that has been run down will start this part at 1.65 V and keep it running until the lockout releases near 1.45 V, and that gap is the usable window at the end of the discharge curve. Any application that has to start at 1.55 V has to look at the sibling that quotes a lower start threshold.

The 8 uA quiescent current is specified into the output pin while the input pin draws 0.15 uA. Those two numbers are measured separately because the part can be powered from either side depending on the mode, and the total is what the battery sees. The shutdown row of 0.5 uA is measured with the enable pin at zero and includes the load disconnect, which is the feature that keeps a depleted cell from being drained by the load rather than by the converter.

The peak switch current limit has a 2.6 A floor and a 3.35 A ceiling. On a converter that is quoted as a 1.5 A part, that window is what protects the inductor and the battery. The floor is the number that guarantees the rated output at the low end of the distribution, and the ceiling is what a short circuit can actually deliver into the inductor before the protection loop reacts. An inductor chosen for 2.7 A saturation sits below the top of that window, which is why the vendor's own application circuit names a 1 uH part with a saturation rating above 3.5 A.

The two package variants differ by one function and nothing else. TPS631011 pulls the output down through an internal switch when the enable pin goes low, at about 67 mA of discharge current. That is slow enough to be harmless for a large output capacitor and fast enough to kill a rail that would otherwise float at a diode drop above ground. A load that has another supply holding its input, or a bus that must not be pulled down, has to take the 010 string, because the discharge is not a pin option that can be disabled.

The three cycle buck boost mode is the part's answer to the awkward region where the input and the output are nearly equal. Instead of hopping between buck and boost every cycle, the converter runs a defined three phase sequence at a fixed duty cycle, which keeps the output ripple from doubling at the crossover point. The cost is a slightly lower efficiency in a narrow input window. A battery powered product spends most of its life away from that window, but a 3.3 V rail fed from a 3.6 V nominal pack crosses it on every discharge, so the ripple there is a real specification rather than a corner case.

There is no tube or small reel row for the YBG body in the vendor addendum, only the 3000 piece large reel. A prototype build either buys a reel or buys from a distributor that has broken one. That matters for a purchasing plan, because a line that expects a 250 piece small reel will not find one, and cutting a reel for a 50 piece pilot run leaves 2950 parts that then have to be stored at moisture level 1, which at least means no bake step before use.

Where this order code fits

It sits in telematics units, optical module bias rails, smart lock and camera front ends, and any handheld product that runs a 3.3 V rail from a single cell whose voltage crosses that rail during discharge. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

How much current can the part really deliver at 3.3 V? 2 A from an input above 3 V, 1.5 A from an input above 2.7 V. The figure falls with the input because the switch current limit of 3 A typical has to serve both sides of the conversion.

What is the difference between the two order codes? TPS631011 adds an active output discharge of about 67 mA when the enable pin goes low. The die, body and reel are otherwise identical.

Does it start at 1.5 V? No. Start up needs 1.65 V. The lockout releases near 1.45 V once running, so the part starts above 1.65 V and keeps running down to about 1.45 V.

What inductor should be used? A 1 uH part whose saturation current sits above the 3.35 A maximum switch limit, because the protection loop reacts after the peak has already been reached.

Is the quiescent current 8 uA? That is the figure into the output pin with no switching. The input pin draws 0.15 uA in the same state, and shutdown total is 0.5 uA including the load disconnect.

Which mode pin setting suits a radio board? MODE high, which forces fixed frequency operation and keeps the switching tone at 2 MHz instead of letting it fall into the band of interest at light load.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.