TPS630702RNMR
Product Specifications
TPS630702RNMR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS630702RNMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS630702RNMR: 2 V to 16 V buck-boost converter, 3.6 A switch, adjustable 2.5 V to 9 V, output discharge
TPS630702RNMR is a four switch buck-boost converter with a 3.6 A switch current that holds an adjustable output between 2.5 V and 9 V from an input that can be above, below or equal to it in a VQFN-HR body of 15 pins. The converter moves between step down and step up automatically, so a rail stays in regulation across a battery discharge that crosses the output voltage. That is the case a buck cannot cover and a boost cannot cover either, and it is why the part appears on lithium powered instruments with a 3.3 V rail.
Order code and package
| TPS630702RNMR | Active, VQFN-HR 15 pin, 3000 pieces on a large reel, the output discharge version, marking 0702 |
| TPS63070RNMR | the adjustable version without output discharge, marking 3070 |
| TPS630701RNMR | the fixed 5 V version without output discharge, marking 0701 |
| Switch current | 3.6 A, which is the switch rating and not the output current |
| Temperature range | minus 40 to 125 degrees junction on the published rows |
Electrical parameters that decide the application
| Input voltage | 2.0 V to 16 V |
| Output voltage | 2.5 V to 9 V, adjustable through an external divider |
| Output current | 2 A in buck mode at 4 V in and 5 V out, and 2 A in boost mode |
| Switch current | 3.6 A, which limits the output current at low input voltage |
| Quiescent current | 50 microamp typical |
| Switching frequency | 2.4 MHz fixed, with a synchronisation option |
| Accuracy | plus or minus 1 per cent in PWM mode, plus 3 and minus 1 per cent in power save |
| Features | power good output, load disconnect in shutdown, input and output overvoltage protection |
Family variants and how they differ
| TPS630702 | adjustable with output discharge, the string on this page |
| TPS63070 | adjustable without output discharge |
| TPS630701 | fixed 5 V without output discharge |
| VSEL and FB2 | a resistor between FB and FB2 lets a logic level switch the output between two values at run time |
| EN pin | a precise threshold, so it doubles as an adjustable undervoltage lockout |
Points to check before this part goes on a BOM
The 3.6 A switch is not 3.6 A of output. In boost mode the input current is higher than the output current, so the switch limit binds sooner as the input falls. At 2 V in and 5 V out the available output current is a fraction of the buck mode figure. The 2 A in the feature list belongs to a 4 V input, and quoting it at 2 V is the most common way this part is specified wrongly.
Automatic transition is the reason to use a buck-boost at all. A lithium cell starts at 4.2 V and ends near 3.0 V, which crosses a 3.3 V rail. A buck drops out at the bottom and a boost cannot work at the top. A four switch converter changes mode in the middle of the discharge and holds the rail, which is what a portable instrument needs.
Output discharge is the difference between the three members. This version pulls the output down when the converter is disabled, so a rail falls quickly and a subsystem does not stay partly powered through a leaking load. The other two members leave the output floating, which is what a board wants when the output is shared with another source.
The VSEL and FB2 pins allow two output voltages without a multiplexer. A resistor between the feedback pin and FB2 changes the divider ratio when VSEL is high, so a logic level moves the rail between two values. That is useful for a system that runs a processor at a low voltage in standby and a higher one under load, and it is a feature that has to be understood before the divider is calculated.
Fifty microamp quiescent is high for a battery product. A buck-boost with four switches has more standing loss than a simple buck, and 50 microamp is the price. For an instrument that is on for hours it is irrelevant; for one that sleeps for weeks the converter should be disabled and a small linear regulator used for the always on domain.
Power save mode changes the output accuracy. The plus or minus 1 per cent figure belongs to PWM mode. In power save the window opens to plus 3 and minus 1 per cent, which is a wide rail. A load that cannot accept that needs the mode pin held to force PWM, at the cost of light load efficiency.
Load disconnect in shutdown is a real function on a battery rail. Without it the inductor and the body diodes provide a path from the cell to the output, and a device that is off still drains. The shutdown current quoted in the data sheet only means something with that path broken, which is why the feature is listed with the current.
Two point four megahertz keeps the inductor small but the part is a four switch topology. There are two inductors in the power path and both carry current in boost mode, so the loss is higher than a simple buck at the same output power. The efficiency is good for a buck-boost and not as good as a buck, and a board that only ever runs above the output voltage should use a buck.
The VQFN-HR body has a small thermal pad and no leads. At 2 A output the dissipation is significant, and the pad is the only path. A pad tied to a copper island with vias is required; a pad connected by a trace will thermal cycle the part and the fault will look like an unstable loop.
What to confirm before this part goes on a purchase order
Confirm which of the three members the board needs. The output discharge and the fixed 5 V versions share a body and a pinout, and the only visible difference is the marking.
State the input range and the output current at the lowest input voltage. The switch current limit, not the headline 2 A, decides what the part can deliver when the battery is nearly flat.
State whether the rail has to be discharged when the converter is disabled, because that single answer picks one of the three members and the three look the same on a reel, and the answer decides whether the rail falls when the subsystem is switched off or stays charged through a leaking load.
Where this order code fits
It holds a rail steady across a battery discharge from 4.2 V down to 2.5 V, where a buck alone would drop out and a boost alone would not start. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can it deliver 2 A at 2 V input? No. Two amps is quoted at 4 V in and 5 V out in buck mode. In boost mode from 2 V the input current is more than twice the output current and the 3.6 A switch limit binds well before 2 A of output.
What is the difference between this and the TPS63070? Output discharge. This string pulls the output down when the converter is disabled; the plain TPS63070 leaves the output floating. The silicon and the pinout are the same.
Does it need two inductors? The four switch topology uses two inductors, one on each side of the switch bridge. Both carry current, so the inductor choice affects efficiency and the board area more than on a simple buck.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.