Contact Us

TPS62825ADMQR

Brand: Texas Instruments
Texas Instruments TPS62825ADMQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62825ADMQR — Power Management & Signal Chain | Superb Automation

TPS62825ADMQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62825ADMQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62825ADMQR: a 2 A step down converter in a 1.5 mm by 1.5 mm six pin package that runs from a 2.4 V to 5.5 V rail

TPS62825ADMQR is a synchronous buck converter built on the DCS-Control loop with a 4 microamp quiescent current, a 2.2 MHz switching frequency and a 0.6 V reference in a VSON-HR (DMQ) body of 6 pins. The 2 A version carries a 26 milliohm high side and a 25 milliohm low side switch, sets the output between 0.6 V and 4 V with an external divider, limits the high side switch between 2.74 A and 3.9 A, and holds 1 per cent output accuracy from minus 40 C to 125 C. The A in this ordering string marks the forced PWM flavour of the family.

Order code and package

TPS62825ADMQRVSON-HR (DMQ) body, 6 pins, 1.50 mm by 1.50 mm, 3000 pieces on a large reel, moisture level 1 at 260 C with unlimited floor life, marking JN, active status in the addendum dated 31 October 2025
TPS62825DMQRthe same body and the same 2 A rating on the plain string, marking CI, which is the power save mode flavour rather than the forced PWM one
TPS62825DMQTthe 250 piece small reel on the same body, which is the string a pilot build orders before the main release
.A suffix rowsthe addendum repeats most strings with an .A suffix and the packing, finish and marking are read per row, because the suffix does not carry the reel size
Fixed voltage rowsTPS6282518DMQR and TPS6282533DMQR are the 1.8 V and 3.3 V fixed output members, and they need no divider at all
SiblingsTPS62824, TPS62826 and TPS62827 are the 1 A, 3 A and 4 A members of the same family, pin to pin and bill of materials compatible
Module versionsTPSM82821, TPSM82822 and TPSM82823 carry the same silicon with the inductor inside the package, for a board that has no room for a separate 470 nH part

Electrical parameters that decide the application

Input voltage2.4 V to 5.5 V, which covers a single cell lithium rail from 2.5 V to 4.2 V and a regulated 5 V rail with margin
Output voltage0.6 V to 4 V adjustable through a divider to the FB pin against a 0.6 V reference
Output current2 A continuous, with the internal switches sized so the current limit sits above the rating rather than at it
Switch resistance26 milliohm on the high side and 25 milliohm on the low side, which is the figure behind the 97 per cent peak efficiency claim
Switching frequency2.2 MHz nominal, with a small controlled variation across the input range, which is why a 470 nH inductor is enough
Quiescent current4 microamp typical and 10 microamp maximum with the enable pin high and no load, on the power save version
Current limit2.74 A minimum, 3.3 A typical and 3.9 A maximum on the high side switch in continuous conduction
Accuracy1 per cent feedback accuracy over the full junction range from minus 40 C to 125 C, which is tighter than the reference tolerance alone would suggest
Soft start1.25 ms typical from enable high to 95 per cent of the set output, 1.75 ms maximum, with no external capacitor needed
Power gooda window comparator that releases between 94 and 98 per cent on the rising edge, asserts below 90 to 94 per cent on the falling edge, and also checks the upper side at 108 to 112 per cent
Undervoltage lockout2.1 V to 2.3 V on a falling input, which is the point where the 5 V rail is treated as gone rather than sagging
Enable thresholds1.0 V to turn on and 0.4 V to turn off, so a 1.8 V logic line drives it directly
Protectionhiccup mode on a short circuit, thermal shutdown at 150 C with 20 C of hysteresis, and active output discharge when the device is disabled
Duty cycle100 per cent duty cycle mode, so the output follows the input down until the switch resistance sets the dropout

Family variants and how they differ

A and plainthe A members run forced PWM in continuous conduction at all loads, which keeps the ripple and the frequency fixed and is what the negative current limit of minus 1.6 A is there for, while the plain members drop into power save mode below half the ripple current
Current rating1 A, 2 A, 3 A and 4 A share one body and one pin out, so a board can be re rated without moving the footprint
Fixed outputsthe 18 and 33 strings set 1.8 V and 3.3 V inside the package and free the FB pin, which removes two resistors and one noise path
Modulesthe TPSM8282x parts move the inductor inside, which trades board area for a taller package and removes the inductor from the sourcing list
Packagethe DMQ body is 1.5 mm by 1.5 mm with six pins on a 0.5 mm pitch, and the VSON-HR outline has no exposed pad to solder
MarkingJN and CI are two character codes that separate the flavours on the reel, and they do not follow the voltage rating

Points to check before this part goes on a BOM

The whole power supply is four parts. A 470 nH inductor, a 4.7 microfarad input capacitor and one 22 microfarad output capacitor, plus the device, which is the reason this family is chosen where the board area is the constraint rather than the part count.

The A string does not power save. Forced PWM keeps the ripple and the switching frequency fixed at light load, which is what an analogue or radio rail needs, but the 4 microamp quiescent current applies to the power save flavour and not to this one.

Power good is a window, not a threshold. It checks the upper side as well as the lower side, so an output that is pulled high by a second source will also release the signal late or not at all.

At 100 per cent duty cycle the output follows the input minus the drop across the high side switch. On a 3.3 V rail from a 3.6 V battery the headroom is thin, and the 26 milliohm switch sets what is left.

The body has no exposed pad. Heat leaves through the pins and the copper they sit on, so the land pattern and the copper area are the thermal solution rather than a pad under the package.

Where a 2 A converter at 2.2 MHz earns its place

A solid state drive, an IP camera or a portable instrument usually has one 3.3 V or 1.8 V rail that has to come from a battery and has to stay efficient when the product is idle. The power save flavour holds efficiency down to a few hundred microamp, and the forced PWM flavour is chosen when the same rail also feeds a radio or a converter that cannot tolerate a variable switching frequency.

At 2.2 MHz the inductor is small enough to sit next to the package, and the switching loss is high enough that the placement of the input capacitor matters more than the inductor value. The input capacitor loop is the one to keep short, because the high side switch current flows through it on every cycle.

Where this order code fits

The part suits a point of load rail for an SSD, an IP camera, a printer or a portable instrument, on a single cell lithium rail that has to hold efficiency at light load. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the difference between the A string and the plain string? The A members run forced PWM in continuous conduction at every load, so the switching frequency and the ripple stay fixed. The plain members enter power save mode below half the inductor ripple current, which raises efficiency at light load and lets the frequency fall.

Is 2 A the real limit at 85 C ambient? The 2 A figure is the continuous output current at the junction temperature the tables are written for. At 85 C ambient the copper under the six pins is what sets the margin, and the current limit of 2.74 A minimum is the absolute ceiling rather than a working current.

Does it need a divider on the fixed voltage versions? No. The 18 and 33 strings set the output inside the package, so the FB pin is not used and two resistors come off the bill of materials.

What replaces this part if it is short? The 1 A and 3 A members are pin to pin, so a short term substitution is possible within the same body, and the module versions carry the same silicon with the inductor inside. SUPERB quotes the substitution against the exact string and states date codes and packing on the offer.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.