Contact Us

TPS62402QDRCRQ1

Brand: Texas Instruments
Texas Instruments TPS62402QDRCRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62402QDRCRQ1 — Power Management & Signal Chain | Superb Automation

TPS62402QDRCRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62402QDRCRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62402QDRCRQ1 dual 400 mA and 600 mA automotive converter at 2.25 MHz

The TPS62402QDRCRQ1 is the dual output member of the TPS6240x-Q1 family, a pair of synchronous step down converters in one package that run at 2.25 MHz with independent enables: converter one delivers 400 mA and is adjustable on this member, converter two delivers 600 mA at a fixed 3.3 V. The input range covers 2.5 V to 6 V, the reference is 600 mV, and the oscillator is specified from 2.0 MHz to 2.7 MHz with a 2.3 MHz typical. The family is AEC-Q100 grade 1 qualified, minus 40 to 125 degrees junction, with HBM classification H2.

The two outputs are not independent in a thermal sense, which is the first thing to understand about a dual converter. Both share one die, one ground and one thermal path, and the sum of the two losses has to leave the junction below 125 degrees. With 400 mA and 600 mA the total is modest, but a board that loads both outputs fully in a hot enclosure is asking for a junction temperature the package cannot shed through a 3 mm by 3 mm body without copper.

The current limit on the first output is 0.68 A minimum, 0.8 A typical and 0.92 A maximum, and the P-channel on resistance is 280 milliohm typical and 620 milliohm maximum at 3.6 V. Start-up takes about 170 microseconds from the enable, plus a ramp of the internal circuits, and each converter has its own enable and its own DEF pin. The MODE/DATA pin does double duty: as a static input it selects between power save and forced PWM for both converters, and as a one wire interface it lets a processor change either output voltage through the EasyScale protocol.

Key parameters from the SLVSA67F document

Input range2.5 V to 6 V, for battery rails and 3.3 V or 5 V system supplies
OutputsConverter one 400 mA adjustable on this member, converter two 600 mA fixed at 3.3 V
Switching frequency2.25 MHz typical, specified from 2.0 MHz to 2.7 MHz over 3 V to 6 V input
Reference600 mV, with 1 per cent accuracy in PWM on the adjustable output
On resistanceP-channel 280 milliohm typical and 620 milliohm maximum at 3.6 V
Current limitConverter one 0.68 A minimum, 0.8 A typical and 0.92 A maximum
Start-upAbout 170 microseconds to start switching, plus the internal circuit ramp
Control interfaceMODE/DATA selects power save or forced PWM, and carries the one wire EasyScale link
EnablesSeparate EN1 and EN2, both active high
QualificationAEC-Q100 grade 1, minus 40 to 125 degrees junction, HBM class H2
Package10 pin VSON, 3 mm by 3 mm, DRC body with thermal pad

Two rails, one package, and the thermal arithmetic

A dual converter saves a package and a set of external parts, and it concentrates the heat. Converter two at 600 mA and 3.3 V from a 5 V input has a duty cycle of 66 per cent, so the high side conducts for two thirds of every cycle at 280 milliohm typical. Converter one at 400 mA and, say, 1.8 V has a duty cycle of 36 per cent and a similar resistive loss. Together the two outputs put roughly a third of a watt into a 3 mm by 3 mm body, which is fine on a board with copper and marginal in a sealed box at 85 degrees ambient.

The 125 degree junction limit of the grade 1 part is what has to be respected, and the thermal pad is the only path that matters. A pad connected to a plane with a via array under the body will hold the junction 40 degrees below one that connects through the pins alone. In a 3 mm body this is not a detail that can be deferred to a thermal simulation after the board is built.

The EasyScale interface is the other unusual feature. One wire from a processor can change either output voltage in steps during operation, which is how a dynamic voltage rail is built without a second converter. On an automotive board that is useful for a processor that runs at two frequencies, and it is only available while the MODE/DATA pin is not being used as a static mode strap, so the two functions cannot be used at once.

Where this part fits

Automotive clusters and body controllers that need a 3.3 V housekeeping rail plus an adjustable core rail, portable instruments with two supplies, and any board that wants two converters in one footprint with a one wire voltage control. Our desk keeps the family comparison across the four -Q1 members and the substitution notes, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

Check which member of the family the board was built for. Four parts share this document: the 4000 with both outputs adjustable, this 4002 with an adjustable first output and a fixed 3.3 V second, the 4004 with fixed defaults, and the 4005 with a different fixed pair. They share a body and a pinout, and the DEF pins decide the default voltages, so a substitution changes the rail that comes up at power on.

Check the thermal pad connection and the copper under the body before the first build, and check the inductor on each output against its own current limit rather than against the load. See incoming inspection plan for the receipt check on a 10 pin VSON with an exposed pad.

Questions that come up on this part

Can the two outputs be enabled independently, is a common question for sequencing. They can, through EN1 and EN2, and the start-up time of about 170 microseconds applies to each. A board that needs one rail to be up before the other has to sequence the enables rather than rely on the internal timing, because the two channels start at the same rate once enabled.

The second question is whether the fixed 3.3 V output can be changed. On this member it cannot: the divider is internal and the DEF pin only chooses between the default and the alternate setting listed in the device table. A board that needs a different second rail should use the fully adjustable member and two resistors.