Contact Us

ADS61B29

Brand: Texas Instruments
Texas Instruments ADS61B29 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS61B29 — Power Management & Signal Chain | Superb Automation

ADS61B29

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS61B29 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS61B29: 12 bit 250 MSPS converter with an integrated analog input buffer in a 48 pin QFN

ADS61B29 is a single channel 12 bit converter that samples at 250 MSPS with the sample and hold driven by an on chip buffer, so the analog front end does not have to drive a switched capacitor load directly in a QFN body of 48 pins. The ADS61B29 is the 12 bit member of a two part family that shares one document and one pin out with the 14 bit ADS61B49. It samples at 250 MSPS, dissipates 790 mW, and puts the samples out on DDR LVDS or parallel CMOS. The feature that separates it from the smaller 32 pin family is the integrated high impedance analog input buffer, which holds a 2 V peak to peak differential input range and a 2.3 V common mode output that the vendor explicitly calls out as different from the ADS6149 family.

Order code and package

Order codeADS61B29
Channelsone
Resolution12 bit
Maximum sample rate250 MSPS
Input bufferintegrated, high impedance analog input
Differential input range2 V peak to peak
Input common mode2.3 V, different from the ADS6149 family
Full scale option1 V peak to peak operation programmable
Output interfaceDDR LVDS or parallel CMOS
Package48 pin QFN, 7 mm by 7 mm
Total power790 mW at 250 MSPS
DocumentADS61Bx9 family data sheet

Electrical parameters that decide the application

Power per sample3.16 nJ at 250 MSPS
Common mode output2.3 V
Offset drift0.005 mV per C, from the offset error table
Gain error, referenceminus 2.5 to plus 2.5 percent of full scale
Gain error, channel0.2 percent of full scale
Gain drift0.001 percent of full scale per C
Clock amplitudedown to 400 mV peak to peak differential
DC offset correctionon chip
Programmable gainup to 6 dB, traded against SNR and SFDR
Pin compatibilitysame pin out as the ADS6149 family and as the 14 bit ADS61B49
Temperatureminus 40 to 85 C
Referenceinternal, with external option

Points to check before this part goes on a BOM

The 2.3 V input common mode is the trap in this part. The document states it is different from the ADS6149 family, so a board that was built around the older common mode and is then fitted with this converter has its drive network biased at the wrong point, which shows up as a compressed or clipped input rather than as an obvious failure.

The integrated buffer is the reason to pay for this body. At 250 MSPS a switched capacitor input has to be charged in a few hundred picoseconds, and a passive transformer network that works at 100 MSPS can fall apart here. The buffer turns that into a high impedance load the drive amplifier can handle, at the cost of its own noise contribution and its own common mode requirement.

Twelve bits at 250 MSPS is a 3 Gbps data stream, and the output is either DDR LVDS or 12 CMOS lines plus clock. On a board that keeps the part but changes the capture device, this is the first thing to re-check: the same converter with a different output mode is a different pin count on the FPGA side.

790 mW at 250 MSPS is 3.16 nJ per sample, and the 48 pin 7 mm body carries that through its pad. The 14 bit sibling in the same body carries the same power, so a board built for the 12 bit part needs no thermal change to take the 14 bit one, which is the usual reason a board starts at 12 bit and later moves up.

Gain error of plus or minus 2.5 percent of full scale from the internal reference is the term that limits absolute accuracy, and it is far larger than the 0.2 percent channel gain error. A board that needs absolute amplitude accuracy has to calibrate against a known source or use an external reference, and the on chip reference alone will not do it.

Offset drift of 0.005 mV per C is 0.6 mV over the 125 C industrial span, which is small against the 1 V full scale option but visible at 12 bit resolution when the input signal is small. It is one of the few parameters in this class that is comfortably inside a single code.

Pin compatibility with the ADS6149 family is stated in the document, and the same body is shared with the 14 bit part. That makes the family useful for a product line that ships two grades from one board, but the substitution rules are not automatic: the common mode difference and the register map both have to be checked before one part replaces another.

Where this order code fits

This order code belongs on multicarrier base station receive paths, software defined radio boards, power amplifier linearisation feedback loops and wideband instrumentation where a 250 MSPS single channel at 12 bit is enough. The buffer makes it attractive where the drive amplifier has to sit far from the converter or where a passive front end cannot supply the sampling current. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the 14 bit ADS61B49 replace this part on the same board? The package and pin out match, so the board does not change, but the resolution, the output word width and the register map do, and the capture side has to be re-checked.

Why does the input common mode matter so much? Because the drive network is biased for it. The 2.3 V figure differs from the older family, so a transformer or amplifier stage carried over from a board built around the ADS6149 family is biased for a different point.

Is the buffer enough to drive the part from a passive front end? It removes the sampling current from the source, which is the hard part at 250 MSPS. The source still has to deliver the signal with low distortion and low noise into the buffer input.

SUPERB supplies this order code with the grade and the packing stated on the offer, and the Obsolete RF Part Replacement page lists the fields that have to match before a 250 MSPS socket is filled from another line.