Contact Us

TPS62262DRVR

Brand: Texas Instruments
Texas Instruments TPS62262DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62262DRVR — Power Management & Signal Chain | Superb Automation

TPS62262DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62262DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62262DRVR: a 600 mA step down converter with a fixed 1.2 V output

TPS62262DRVR is a 600 mA synchronous step down converter with a fixed 1.2 V output, running at 2.25 MHz from a single lithium cell or a 3.3 V rail in a WSON body of 6 pins. A fixed 1.2 V output removes the divider and its drift, and the 2.25 MHz switching frequency keeps the inductor and the output capacitor small enough for a phone board.

Order code and package

Catalogue stringTPS62262DRVR, decoded as fixed 1.2 V, DRV body, R reel letter
BodyDRV, WSON, 6 pins, 2.00 mm by 2.00 mm by 0.8 mm
Second bodyDDC, SOT, 5 pins, 2.90 mm by 1.60 mm, the version without a mode pin
Reel250 pieces on the DRV body for this string in the printed rows
Temperatureminus 40 to 85 C ambient
MarkingBYM on the DRV body
DocumentSLVS763E, revised July 2015

Electrical parameters that decide the application

Input range2.3 V to 6 V in the electrical table, against 2 V to 6 V in the features list
Output1.2 V fixed, 600 mA
Current by input600 mA from 2.5 V to 6 V, 300 mA from 2.3 V to 2.5 V, 150 mA from 2 V to 2.3 V
Switching frequency2.25 MHz fixed
Accuracyplus or minus 1.5 per cent in PWM mode
Quiescent current15 uA typical with power save enabled and the device not switching
Quiescent current, PWM3.8 mA with the mode pin high and the part switching with no load
Shutdown current0.1 uA typical, 1 uA maximum
High side resistance240 mOhm typical, 480 mOhm maximum
Low side resistance185 mOhm typical, 380 mOhm maximum
Current limit0.8 A minimum, 1 A typical, 1.2 A maximum
Undervoltage lockout1.95 V rising, 1.85 V falling
Enable thresholds1 V high, 0.4 V low, 0.01 uA of pin current
Duty cycle100 per cent, so the output follows the input when the cell is nearly flat

The four members and the two bodies

TPS62260adjustable output, WSON and SOT bodies, the member with a mode pin on both
TPS622611.8 V fixed, WSON and SOT bodies
TPS622621.2 V fixed, WSON and SOT bodies, the part on this page
TPS622632.5 V fixed, WSON body
Mode pinpresent on the WSON versions of several members and absent on the SOT row, so the ability to force PWM depends on the body and not only on the voltage
Inductor and output capacitor2.2 uH and 10 uF are the values the electrical table is specified with, and a smaller inductor moves the ripple and the efficiency away from the published curves
Package height0.8 mm in the WSON body, which is what allows a solution under 1 mm
Markingeach member and body combination has its own four character marking, which is the only way to tell them apart once they are out of the reel

Points to check before this part goes on a BOM

The output current rating depends on the input voltage in a way that catches people out. Six hundred milliamps is quoted from 2.5 V up, and the same part is a 300 mA part from 2.3 V to 2.5 V and a 150 mA part below that. A product running from a cell that ends at 3.0 V never sees the derated region, one running to 2.4 V does.

Fifteen microamps of quiescent current applies with power save enabled. Pulling the mode pin high for forced PWM raises the no load current to 3.8 mA, which is a factor of two hundred and fifty. On a battery product the mode pin is therefore a power decision and not only a noise decision.

The current limit window is 0.8 A to 1.2 A on a 600 mA part. The minimum is only a third above the rating, so a load that draws a 1 A pulse while the output capacitor is discharged can hit the limit before the rail is up. The soft start of the load, not a bigger inductor, is the usual fix.

Undervoltage at 1.95 V rising and 1.85 V falling is above the 1.8 V a two cell alkaline pack reaches at the end of its life, which means the converter turns off while the cells still have some charge. That is deliberate on a lithium product and a nuisance on an alkaline one.

Sixty nine degrees of ambient range and no junction figure in the features list is a reminder that this is an older part. At 240 mOhm and 600 mA the conduction loss is about 86 mW, which is fine at 85 C ambient on a reasonable land, and marginal on a two layer board with no copper under the body.

A five pin SOT version without a mode pin exists for the same voltage. A buyer substituting it for the WSON row gets the same electrical behaviour in power save and loses the ability to force continuous conduction, which matters on a rail feeding an analogue block.

What changes when the mode pin goes high

In power save the converter skips cycles at light load and the output ripple grows while the current falls. Pulling the mode pin high forces continuous switching, which keeps the ripple constant and the switching tone fixed, at the cost of a no load current in the milliamps.

An analogue or RF block usually wants the forced mode, because a converter that changes its switching pattern under a light load puts a moving tone into the supply. A digital rail that sleeps most of the time wants power save, because the milliamps of forced mode are the whole standby budget.

Fixed output and the missing divider

A fixed 1.2 V part has the divider inside the package. That removes two resistors, removes their drift, and removes the leakage path through them, which on a 15 uA converter is a noticeable fraction of the total.

It also removes the ability to trim. A board that needs 1.25 V has to change the part, and a board that needs to compensate a drop in the load has to do it in the load rather than at the converter.

Where this order code fits

This is the point of load converter behind a processor core, a memory rail or a low power DSP supply, where a fixed 1.2 V is what the load wants and board area is tight. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it run from a single lithium cell? Yes, from 2.5 V to 4.2 V at the full 600 mA. Below 2.5 V the current rating falls, and below 2.3 V the part is outside its specified operating range even though the features list mentions 2 V.

Is the 1.2 V output adjustable? No. The divider is internal. A rail that needs 1.5 V uses the 2.5 V member with an external divider only if the family offers it, and this one does not.

What inductor should be used? The electrical table is specified with a 2.2 uH inductor and a 10 uF output capacitor. Those are the values the numbers apply to, and a smaller inductor moves the current ripple and the efficiency away from the published curves.

How much does forced PWM cost? About 3.8 mA at no load against 15 uA in power save. On a mains powered board that is nothing, on a battery product it is the difference between months and days of standby.

Does it need an external diode? No, the low side switch is integrated and synchronous rectification is used. The 185 mOhm low side figure is the resistance of that switch.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.