TPS62170DSGR
Product Specifications
TPS62170DSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62170DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62170DSGR: 500 mA step-down converter from 3 V to 17 V in a 2 mm by 2 mm package
TPS62170DSGR is a 500 mA synchronous buck converter for a 12 V or 24 V rail that has to produce a small low voltage housekeeping supply in a two millimetre body in a WSON body of 8 pins. The TPS62170 takes 3 V to 17 V in and delivers up to 500 mA, with an adjustable output from 0.9 V to 6 V on the adjustable member and fixed options across the family. It uses a control scheme with a seamless transition into power save at light load, runs at about 2.25 MHz in continuous conduction, and draws 17 uA quiescent. The internal reference is 0.8 V, the current limit is 1.05 A typical at a 12 V input, and the part is pin compatible with the TPS62160 and the TPS62125 so one board can carry several members.
Order code and package
| Order code | TPS62170DSGR |
| Input voltage | 3 V to 17 V |
| Output current | up to 500 mA |
| Output voltage | adjustable 0.9 V to 6 V |
| Switching frequency | about 2.25 MHz in continuous conduction |
| Quiescent current | 17 uA typical |
| Shutdown current | 1.5 uA typical at 25 C |
| Reference | 0.8 V internal |
| Package | 8 pin WSON, 2 mm by 2 mm |
| Pin compatibility | TPS62160 and TPS62125 |
| Power good | open drain output with a 0.3 V low level at 2 mA |
| Document | SLVSAT8E, November 2011, revised May 2017 |
Electrical parameters that decide the application
| Current limit | 0.85 A minimum, 1.05 A typical, 1.35 A maximum at 12 V in |
| High-side resistance | 300 mOhm at 6 V in and above, 600 mOhm at 6 V |
| Low-side resistance | 120 mOhm at 6 V in and above, 200 mOhm at 3 V |
| Input UVLO falling | 2.6 V minimum, 2.7 V typical, 2.82 V maximum |
| Thermal shutdown | 160 C rising, 20 C hysteresis |
| Output accuracy in PWM | minus 3 percent to plus 3 percent with a 1 V input to output differential |
| Power good rising | 92 percent to 98 percent of the output |
| Power good falling | 87 percent to 93 percent of the output |
| Enable leakage | 0.01 uA typical, 1 uA maximum |
| Feedback leakage | 5 nA typical, 400 nA maximum |
| Junction range | -40 C to 125 C |
| Duty cycle | 100 percent mode at dropout |
Points to check before this part goes on a BOM
Seventeen microamps of quiescent current with a 17 V input ceiling is the combination that makes this part useful on an industrial rail. A bias supply that sits across a 24 V bus has to survive the transients on that bus and still draw almost nothing when the load is asleep, and the 3 V to 17 V range covers a 12 V rail with margin for both directions.
The current limit of 1.05 A typical against a 500 mA rating looks generous, but it is the peak switch current and the inductor decides how much of it is ripple. At 2.25 MHz with a 2.2 uH inductor and a 12 V input the ripple is close to 0.35 A, so a 500 mA load sits at about 0.67 A peak, comfortably inside even the 0.85 A minimum limit.
The control scheme keeps the output within 3 percent in forced pulse width modulation but allows a wider window when power save is active. A load that needs a tight rail at light current should be checked against the power save behaviour rather than the pulse width modulation row, because the part changes its positioning when it starts skipping cycles.
Pin compatibility across the TPS62160, TPS62170 and TPS62125 is a procurement advantage. A board can be laid out once and populated with the member that matches the load, and a shortage on one member can be covered from another without a board change, provided the current rating and the feedback network suit the substitute.
The 2 mm by 2 mm body has no exposed pad in the usual sense, so the ground pins and the copper under the package are the thermal path. At 500 mA from 12 V to 3.3 V the loss is around 0.15 W, which is small, but a board that stacks this part next to a hot regulator should check the ambient at the package rather than the ambient at the board edge.
The power good output is open drain and needs a pull up. Its rising threshold is 92 to 98 percent of the output and its falling threshold is 87 to 93 percent, so the hysteresis is only a few percent and a rail that sits near the threshold under load will chatter the flag. Sequencing logic that depends on this pin should add its own filter or use a separate supervisor.
At 2.25 MHz the switching harmonics land above the medium wave band, which is helpful in an instrument that also carries an analog front end. The part is not synchronisable, so a board with several converters on different frequencies needs the emission plan to account for the beat between them rather than a common clock.
Where this order code fits
This order code fits housekeeping and bias rails on industrial controllers, metering, motor drives and telecom cards that run from 12 V or 24 V and need 3.3 V or 5 V at a few hundred milliamps. The wide input and the 500 mA ceiling make it a bias supply for gate drivers, op amps and sensors rather than a main rail. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.
Questions buyers ask
What is the difference between the TPS62170 and the TPS62171? The TPS62170 is the adjustable member; the 62171, 62172 and 62173 are fixed output members in the same body and pin out.
Can this run from a 24 V rail? The absolute input ceiling is 17 V, so no. A 24 V bus needs a part with a higher rating even though the steady state is within reach.
Does the current limit protect the inductor? It limits the peak switch current at 1.05 A typical, so the inductor saturation rating has to be above the 1.35 A maximum column.
SUPERB quotes this order code with packing and date codes, and the Component Lead Time Solutions page lists the fields to check when a bias rail has to be kept available after the original part is discontinued.