Contact Us

TPS62135RGXR

Brand: Texas Instruments
Texas Instruments TPS62135RGXR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62135RGXR — Power Management & Signal Chain | Superb Automation

TPS62135RGXR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62135RGXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62135RGXR: 17 V input, 4 A step-down converter with 1 per cent accuracy and an 18 uA quiescent current

TPS62135RGXR is a synchronous buck converter in the DCS-Control family that holds a tight output window at full load and still draws microamps when the load sleeps in a VQFN-HR (RGX) body of 11 pins. It takes 3 V to 17 V in, delivers 4 A at any output from 0.8 V to 12 V, switches at a typical 2.5 MHz in forced PWM, and quotes 1 per cent output accuracy in PWM mode against 2 to 2.5 per cent in power save mode. The body is 3 mm by 2 mm, and the enable pin has a 0.8 V threshold, which lets a resistor divider turn it into a precise undervoltage lockout.

Order code and package

Ordering stringTPS62135RGXR, the 11 pin VQFN-HR body on a 3000 piece large reel
Part marking62135 on the body, against 621351 on the sibling part, so the two are told apart by the marking rather than by the package
Body11 pin VQFN-HR, 3.00 mm by 2.00 mm, with the thermal pad underneath
MaterialRoHS compliant, tin lead finish, moisture level 1 with unlimited floor life at 260 degrees
SiblingTPS621351 uses the same die and the same pinout but drops the active output discharge and the hiccup overcurrent response
Orderable rowsThe addendum prints the R and T reel sizes plus .A and .B split rows, so the reel size and not just the suffix decides which row applies
Temperatureminus 40 to 125 degrees junction, which is the figure the electrical table is specified over

Electrical parameters that decide the application

Input range3 V to 17 V, with a 2.9 V rising and 2.6 V falling undervoltage lockout, so a 3.3 V rail sits only 0.3 V above the lockout
Output range0.8 V to 12 V, adjustable with an external divider into a 0.7 V reference, with 100 per cent duty cycle mode for dropout operation
Output current4 A continuous, limited by a 4.8 to 6.5 A switch window at 5.6 A typical rather than by a fixed foldback point
Switching frequency2.5 MHz typical with MODE held high in forced PWM, and an adaptive frequency in power save mode that tracks the input to output ratio
Quiescent current18 uA typical and 46 uA maximum at 25 degrees, 35 uA maximum at 85 degrees junction
Shutdown current1 uA typical and 8 uA maximum, with the output actively discharged on this member
Switch resistance100 mOhm high side typical and 180 maximum, 39 mOhm low side typical and 67 maximum, both quoted at 4 V in or above
Accuracy1 per cent in PWM mode, 2 per cent in power save above 1.5 V out, 2.5 per cent below that, all against a 0.7 V reference window
Inductor window0.6 uH to 2.9 uH effective, with 1 uH as the nominal value the efficiency curves are drawn at
Output capacitor6 uF to 200 uF effective at the output, at least 3 uF at the input, both quoted after the dc bias derating of ceramic parts
Enable threshold0.8 V rising and 0.7 V falling with 100 nA of leakage, precise enough to set a lockout with a two resistor divider
Power good96 per cent of nominal on the way up, released with about 3 per cent of hysteresis, open drain and rated to 5 V
Thermal38.4 degrees per watt junction to ambient on a four layer board with six thermal vias, which sets the 4 A ceiling at high duty
Soft start200 to 300 us from enable to the first switching pulse, then a 150 us ramp with the tracking pin open

Family variants and how they differ

TPS621351Same die, same pinout, no output discharge and no hiccup. A short on the rail on this member retries through the hiccup counter, while the 621351 stays in current limit until the fault is removed
The VSEL pinPulling VSEL high closes an internal switch from the second feedback pin to ground, which puts a second divider in parallel with the first and raises the output. It is a two level scaling pin, not a second regulation loop, and the switch resistance of 10 to 30 ohm is part of the divider tolerance
MODE pinHolding MODE high forces PWM at 2.5 MHz for a predictable ripple, and holding it low enables the adaptive frequency and the AEE behaviour that improves light load efficiency
FB2 toleranceBecause the scaling switch sits in series with the external resistor, the second output level carries a wider error than the first. A rail that has to be accurate at both levels needs the divider computed against the switch resistance, not against the resistor alone
Duty cycle at 100 per centThe part can hold the high side FET on continuously, which turns it into a resistive path from input to output once the input falls close to the output. Dropout in that state is the input current times the high side resistance, not a switching loss
Thermal padThe 11 pin body has no lead frame to spread heat, so the pad and the via field under it carry the whole 4 A dissipation. At 12 V to 3.3 V and 4 A that is roughly 1.1 W in the converter alone

Points to check before this part goes on a BOM

The 1 per cent accuracy claim belongs to PWM mode. In power save mode the window opens to 2 per cent above 1.5 V out and 2.5 per cent below, which is what a load that sleeps on a tight rail has to be checked against.

The enable threshold of 0.8 V rising is the reason this part is often used as its own undervoltage lockout. A divider from the input sets the exact turn on point, and the 100 nA of leakage keeps the divider current low enough for a battery rail.

The 2.9 V rising lockout sits above a fresh 3.3 V rail by only 0.4 V. A supply that droops on load or a battery that sags near end of life can cross that line, and the converter then restarts rather than regulating through it.

Switch current limit is a window, not a point. On a 4 A load the part can limit anywhere between 4.8 A and 6.5 A, so an inductor has to be rated for the top of that window and not for the nominal load.

The hiccup response on this member retries after a wait, which keeps a persistent short from cooking the board but also means a marginal load can present as a rail that pulses. The 621351 sibling latches instead, and the difference is not visible from the part number prefix.

Output capacitance above 200 uF is outside the specified window unless the extra capacitance carries series resistance. Boards that stack many small ceramic parts close to the load are the usual case where that limit is exceeded without anyone noticing.

What the two level scaling pin is for

A processor that runs a rail at one voltage in its fast state and a lower voltage in its idle state needs either a second regulator or a way to move the set point from the first. The VSEL pin on this part moves it by switching a second divider in parallel, which is cheap and needs no extra wire to the controller beyond one logic line.

The price is accuracy at the second level. The switch that grounds the second divider has 10 to 30 ohm of resistance, and that resistance sits in series with a divider leg that may only be tens of kiloohm. A board that needs both levels within 1 per cent has to compute the lower resistor against the switch resistance, or accept the wider window.

Where this order code fits

Connected standby rails in mobile and embedded computers, solid state drive supplies, gaming consoles, 12 V intermediate rails and point of load supplies running from a multi cell lithium pack. What these loads share is a rail that has to be efficient at a few milliamps while the processor sleeps and still deliver 4 A the moment it wakes, which is the case this part was tuned for rather than a converter that only quotes peak current. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the output be moved between two levels from a logic pin? Yes, through VSEL. It puts a second divider in parallel with the feedback network, so the second level is set by that divider and carries the tolerance of the internal switch as well as the resistors.

Is the 1 per cent accuracy available in power save mode? No. Power save opens the window to 2 per cent above 1.5 V out and 2.5 per cent below, because the loop is comparing the output against a threshold rather than regulating it every cycle.

What inductor does it need? 1 uH nominal, with the specified window running from 0.6 uH to 2.9 uH effective. Anything smaller than 0.6 uH changes the ripple and the current limit behaviour outside the specified range.

Does it require an external compensation network? No. The control loop is internally compensated, and the passive window of 0.6 to 2.9 uH with 6 to 200 uF at the output is what the stability is specified against.

What happens when the output is shorted? On this member the part enters hiccup, waits, and retries, so the average current stays low. The TPS621351 does not hiccup and simply holds the current limit until the short is removed.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.