Contact Us

TPS62130RGTR

Brand: Texas Instruments
Texas Instruments TPS62130RGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62130RGTR — Power Management & Signal Chain | Superb Automation

TPS62130RGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62130RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62130RGTR: 3 V to 17 V, 3 A step down converter with DCS control in a 3 mm QFN

TPS62130RGTR is a synchronous buck converter with a hysteretic DCS loop, a selectable switching frequency and a pin that adds five per cent for margining in a QFN body of 16 pins. It is the three amp workhorse for 12 V rails that need a small body, no external compensation and a defined behaviour in power save mode.

Order code and package

Order codeTPS62130RGTR, RGT package, 3000 pieces on a large reel
BodyQFN, 3.0 mm by 3.0 mm, 16 pins with a thermal pad
ControlDCS-Control, a hysteretic loop with a fixed frequency in continuous mode
Frequency pin2.5 MHz with FSW low, 1.25 MHz with FSW high, an internal 400 kOhm pull down
DEF pinRaises the regulated output by 5 per cent for margining when pulled high
Reference800 mV, 788 mV to 812.8 mV over the temperature range

Electrical parameters that decide the application

Input range3 V to 17 V operating, functional down to the 2.7 V lockout
Output current3 A continuous, high side forward limit 3.6 A to 4.9 A
Output range0.9 V to 6 V adjustable on this version, the fixed versions are separate order codes
High side switch90 mOhm at 6 V and above, 170 mOhm at 3 V
Low side switch40 mOhm at 6 V and above, 70 mOhm at 3 V
Switching frequency2.5 MHz or 1.25 MHz selected by the FSW pin
Quiescent current17 uA typical and 30 uA maximum while not switching, 1.5 uA to 25 uA shut down
Soft start2.5 uA source current on the SS/TR pin, so the ramp follows an external capacitor
Under voltage lockout2.6 V to 2.8 V falling, 200 mV of hysteresis
ProtectionHigh side current limit, thermal shutdown at 160 C, power good with 92 to 98 per cent rising

Family variants and how they differ

TPS62130Athe adjustable member of the same family with a revised die, otherwise the same body and pin out
TPS62131 and TPS62132 and TPS62133fixed 1.8 V, 3.3 V and 5 V versions, selected by the DEF pin rather than a divider
TPS62140 and TPS62150pin compatible parts at 4 A and 5 A, so a board can be re-rated upward
TPS56C21512 A in a larger body for a load this part cannot reach
TPS62410two independent 800 mA outputs from 6 V, for a board with two light rails

Points to check before this part goes on a BOM

The DEF pin is a margining input, not a mode pin. Pulling it high raises the regulated output by 5 per cent, which is useful for a production test that has to prove the load works at the top of its supply window, and dangerous if it is left floating high on a board that also expects a tight 3.3 V. The pin has an internal 400 kOhm pull down so that a floating pin reads low, which is the safe default.

The frequency choice changes both the inductor and the minimum pulse. At 2.5 MHz the loop can use a 1 uH inductor and a small output capacitor, and the minimum on time limits how far the output can sit below a 12 V input. At 1.25 MHz the same rail runs with lower switching loss and a larger inductor, and the data sheet recommends at least a 2.2 uH part to hold full current at the lower frequency.

The high side current limit is 3.6 A minimum against a 3 A rating, so the margin is 0.6 A. With 2.5 MHz switching the ripple is small, which is why the part can rate 3 A against a 3.6 A limit, but a build that lowers the frequency to 1.25 MHz for efficiency raises the ripple and eats into that margin. The current limit is a protection threshold, not a regulated value, and it is specified at 12 V input where the duty cycle is low.

The switch resistances are quoted at two input voltages because they move, 90 mOhm at 6 V and 170 mOhm at 3 V for the high side, and 40 mOhm against 70 mOhm for the low side. At 3 A from 12 V to 5 V the conduction loss is 0.23 W in the high side and 0.26 W in the low side, and a 3.3 V input doubles the high side term. A rail running from a 3.3 V source at 3 A is not the same thermal problem as the same rail from 12 V.

DCS-Control has no external compensation, but it does expect the output capacitor in a band. Too little capacitance and the hysteretic loop sees the ripple as noise and runs at an uneven frequency; too much and the loop is slow to respond to a load step. The data sheet works its examples at 22 uF, and a build that halves or doubles that value should re-measure the transient rather than assume the loop is unchanged.

The under voltage lockout falls between 2.6 V and 2.8 V, which is above the 3 V minimum input but below a 3.3 V rail at minus ten per cent. A 3.3 V rail at minus fifteen per cent, 2.8 V, sits at the top of the lockout window and the part may drop out. Any board that runs this part from a 3.3 V source has to check the worst case low line against that window, not against the 3 V headline.

Pin compatibility with the 4 A and 5 A members of the family is worth knowing at the sourcing stage. The same 16 pin footprint takes TPS62140 and TPS62150, so a board built for 3 A can be re-rated without a board change, and a shortage of the 3 A part can sometimes be covered by the larger one if the inductor and the output capacitor are checked. That is a cheaper route than a new board and a common way to keep a line running.

Power save mode keeps the quiescent current at 17 uA by dropping cycles at light load, and the transition to continuous operation happens at a load set by the input voltage. A rail that feeds a radio or an analog front end should be checked at the load where the mode changes, because the ripple and the frequency both move there and a receiver can hear the boundary even when it is quiet at full load.

The soft start pin sources 2.5 uA, so the ramp time is the capacitor value times the target voltage divided by that current. A 10 nF capacitor gives roughly 13 ms to 3.3 V, which is a common way to keep inrush under the current limit on a board with a large output bank. The same pin can be used as a tracking input, which is how two rails are made to rise together in a sequenced system.

Where this order code fits

It belongs on the 12 V rail of a solid state drive, an embedded computer, a modem, a camera or a point of sale terminal, where a 3 A rail has to be small, quiet at light load and free of external compensation parts. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What is the difference between this and the TPS62130A? The A version is a revised die with the same body and pin out. Both are adjustable, and the A part is the one to specify on a new build.

Can the output be 0.8 V? No, 0.9 V is the bottom of the adjustable range. The 800 mV reference plus the divider sets the floor, and the part needs the output above it to regulate.

Does the DEF pin affect the output? Yes, it raises the regulated voltage by 5 per cent for margining. It has an internal pull down, so leaving it open gives the nominal output.

Can it be replaced by a higher current part? The TPS62140 and TPS62150 share the footprint at 4 A and 5 A. The inductor and output capacitor have to be checked, but the board does not change.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.