Contact Us

TPS62088YFPR

Brand: Texas Instruments
Texas Instruments TPS62088YFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62088YFPR — Power Management & Signal Chain | Superb Automation

TPS62088YFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62088YFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62088YFPR: a 3 A step down converter at 4 MHz in a 0.8 mm by 1.2 mm wafer chip scale body

TPS62088YFPR is a synchronous step down converter with the DCS-Control loop and a 4 MHz switching frequency in a DSBGA (YFP) body of 6 pins. It takes 2.4 V to 5.5 V in and delivers 3 A at an adjustable output voltage from a body measuring 0.8 mm by 1.2 mm and 0.5 mm tall. Both switches measure 26 milliohm, the quiescent current is 4 microamp, the output is held to 1 per cent, and the 4 MHz frequency lets a 0.24 microhenry inductor do the work that a much larger part would need at 1 MHz.

Order code and package

TPS62088YFPRDSBGA body of 6 pins measuring 0.80 mm by 1.20 mm and 0.50 mm tall on a 0.4 mm pitch, 3000 pieces on a large reel, tin silver copper finish, moisture level 1 at 260 C with unlimited floor life, marking 15X, active status in the addendum dated 8 November 2025
Addendum alignmentthe packaging table prints the quantity one row above the part number for this family, so the reel size is read from the R and T suffix, with R at 3000 on a large reel and T at 250 on a small reel
TPS6208812YFP and TPS6208818YFP and TPS6208833YFPthe fixed 1.2 V, 1.8 V and 3.3 V members, same body, same reel, markings 1B5, 1B6 and 1B7
TPS62088AYFPthe forced PWM member at 3 A adjustable, marking 15X on the row that carries the A
TPS62089AYFPthe forced PWM member rated 2 A, with a lower current limit window
TPS62088YWCRthe same die in a 0.3 mm tall body, which is the version used where the board has to fit inside a 0.6 mm stack

Electrical parameters that decide the application

Input voltage2.4 V to 5.5 V, which covers a single cell lithium battery, a 3.3 V bus and a 5 V adapter
Output voltageadjustable up to the input voltage on this string, with fixed 1.2 V, 1.8 V and 3.3 V members in the same family
Output current3 A on the adjustable and fixed members, and 2 A on the forced PWM member, with the data sheet noting that continuous 3 A above 85 C junction shortens the life of the YFP body
Switch resistance26 milliohm on the high side and 26 milliohm on the low side, which is the figure that sets the conduction loss at 3 A
Switching frequency4 MHz, which is high enough that the inductor is 0.24 microhenry and the output capacitor is small
Quiescent current4 microamp typical and 10 microamp maximum with the enable high and the part not switching
Current limit3.6 A minimum, 4.3 A typical and 5.0 A maximum on the high side switch for this member, against 2.7 A to 3.9 A on the 2 A forced PWM member
Negative limitabout minus 1.6 A on the low side in forced PWM, which is what allows the output to sink current when a rail is pulled above its set point
Output discharge75 mA typical and 400 mA maximum through an internal switch when the enable goes low, which collapses a small rail quickly
Accuracy1 per cent over the specified range, which includes the reference and the load regulation together
Duty cycle100 per cent, so the part follows the input down to the output voltage without dropping out early
Power goodan open drain output, with a sink current of up to 2 mA and a pull-up allowed to 5.5 V
Junction rangeminus 40 C to 125 C, with thermal shutdown and hiccup short circuit protection behind it

Members of the same family and how they differ

TPS6208812 and 18 and 33fixed 1.2 V, 1.8 V and 3.3 V members at 3 A, same 6 pin body, markings 1B5, 1B6 and 1B7
TPS62088Athe forced PWM member at 3 A, which holds continuous conduction at light load and loses the power save efficiency
TPS62089Athe forced PWM member rated 2 A with a 2.7 A to 3.9 A current limit, which is the part for a rail that never needs more than 2 A
YWC bodythe same die in a 0.3 mm tall body, against 0.5 mm for the YFP body, for a stack that has to fit inside 0.6 mm
Modethe plain members run power save at light load and the A members run forced PWM, so the string decides the light load behaviour rather than a pin
Output discharge75 mA typical and 400 mA maximum through an internal switch on all members, which collapses a small rail without an external part
Inductor0.24 microhenry in the reference circuit, a direct consequence of the 4 MHz switching frequency

Points to check before this part goes on a BOM

The 3 A rating has a temperature condition attached. The recommended operating table states that continuous 3 A operation above 85 C junction shortens the life of the YFP body. A rail that sits at 3 A inside a sealed enclosure at 70 C ambient is already past that point unless the copper under the part is generous.

4 MHz is what makes the body small and the board quiet. The inductor is 0.24 microhenry, which is a part the size of a grain of rice, and the switching harmonics sit far above the bands that a radio or an analog front end cares about. The cost is switching loss, which is why the efficiency curve bends earlier than a 1 MHz part.

The current limit window is 3.6 A to 5.0 A. A 3 A load with a 20 per cent transient reaches 3.6 A, which is the minimum limit, so a rail with a large transient needs the inductor and the output capacitor sized so the limit is not reached rather than relying on the headroom.

The discharge is strong on this part. 400 mA maximum through an internal switch is enough to collapse a 22 microfarad rail in tens of microseconds, which matters when a downstream device has a re power sequence requirement.

The 0.3 mm body is a different string. The YWC body is 0.3 mm tall and the YFP body is 0.5 mm, and both are 6 pin DSBGA. A stack height requirement that quotes 0.6 mm needs the YWC string, not a lower profile board.

Two 26 milliohm switches at 3 A dissipate real power. The conduction loss alone is about 470 mW at 3 A, which is more than a 0.8 mm body can pass to still air, so the thermal answer is the board copper under the balls rather than the package.

What a 4 MHz converter changes for the board

The inductor at 0.24 microhenry is small enough to sit next to the part, and the output capacitor is a 10 microfarad ceramic rather than a bank. That is the difference between a converter that fits under a shield can and one that does not, and it is usually the reason a 3 A rail ends up on a part this small.

The high frequency also moves the ripple into a band that is easier to filter, but it raises the switching loss at high input. A rail that runs from 5 V down to 1 V at 3 A loses more in the switches than a 1.5 MHz part would, so the choice is a board area and height decision as much as an efficiency one.

Where this order code fits

a solid state drive, an optical module or a wearable that needs a 3 A core rail inside a 0.6 mm stack Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is 3 A available at any temperature? 3 A is the rated current, and the data sheet notes that continuous operation at 3 A above 85 C junction shortens the life of this body. The copper under the part and the ambient inside the enclosure decide what the rail can really carry.

What inductor does it need? 0.24 microhenry in the reference circuit, because the switching frequency is 4 MHz. A larger inductor lowers the ripple and slows the transient, and it also takes more board area than the part itself.

Can the output be set below 0.8 V? The output is adjustable from the reference up to the input voltage, and the reference is 0.6 V. A rail below that needs a different part or a divider with an amplifier.

What is the difference between the plain string and the A string? The plain TPS62088 runs in power save mode at light load and the A string runs in forced PWM, which keeps a fixed frequency but costs light load efficiency. The 3 A rating applies to both, and the 2 A rating applies to the TPS62089A.

Does it discharge the output when disabled? Yes, through an internal switch rated 75 mA typical and 400 mA maximum, which collapses a small rail quickly without an external part.

How is this string packed? 3000 pieces on a large reel with moisture level 1 at 260 C and unlimited floor life, and SUPERB states the date code, packing and country of origin on the offer.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.