Contact Us

TPS62085RLTR

Brand: Texas Instruments
Texas Instruments TPS62085RLTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62085RLTR — Power Management & Signal Chain | Superb Automation

TPS62085RLTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62085RLTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62085RLTR: 2.5 V to 6 V input, 3 A step-down with 17 microamp quiescent current

TPS62085RLTR is a synchronous step-down converter that keeps efficiency high from full load down to microamp loads in a QFN body of 7 pins. It converts 2.5 V to 6 V down to a fixed 1.8 V or 3.3 V or any adjustable value above 0.8 V at up to 3 A, switches at 2.4 MHz, and draws 17 microamp with no load.

Order code and package

Ordering stringTPS62085RLTR, RLT package, 2 mm by 2 mm QFN, tape and reel
Output optionsFixed 1.8 V and 3.3 V versions plus an adjustable version from 0.8 V to VIN
Package7-pin QFN, 2.00 mm by 2.00 mm
Ambient range-40 C to 85 C
Pin count checkVIN, SW, GND, VOS, FB, EN and PG, with the pad as the seventh connection

Electrical parameters that decide the application

Input range2.5 V to 6.0 V
Current3 A rated
Switch resistance31 milliohm typical, 56 milliohm maximum, high side
Switching frequency2.4 MHz nominal in forced PWM
Quiescent current17 microamp in power save mode
ControlDCS-Control, which moves between PWM and power save without a mode pin
Output floor0.8 V on the adjustable version

Points to check before this part goes on a BOM

At 2.4 MHz the on time is short at any large step-down ratio: 6 V in to 0.8 V out is a 13 percent duty cycle, which is 55 ns, and 5 V in to 1.8 V is 150 ns. The part is comfortable at those numbers, but the minimum on time is what caps the usable input range at the low end of the output range, so a 6 V input with a 0.8 V output belongs in the timing check rather than in the efficiency table.

The 17 microamp quiescent current is the headline, and it only applies in power save mode at light load. In forced PWM the part runs at a fixed frequency and the supply current is set by the gate drive, so a system that needs a quiet spectrum pays in standby current, and a system that needs standby current pays in ripple at light load. DCS-Control moves between the two on its own, which is convenient until the transition point lands in the middle of a measurement band.

Conduction loss at 3 A is 31 milliohm on the high side for the duty share, so from 5 V to 1.8 V it is about 0.10 W, and the low side carries the larger share at a similar resistance. The 2 mm by 2 mm body has no room for a lead frame, so the pad and the vias under it are the entire thermal path, and 3 A continuous is a copper question before it is a silicon question.

The inductor value follows from the frequency: at 2.4 MHz, 5 V in and 1.8 V out, a 1 microhenry part gives about 0.48 A of peak-to-peak ripple, which is 16 percent of the 3 A rating. Doubling the inductor halves the ripple and slows the load-step response, and the loop was compensated for the reference value, so a large change in inductance is a stability question.

The fixed output versions remove the divider and its tolerance, which matters at 0.8 V where a one percent divider pair contributes more error than the reference. The adjustable version is the right choice only when the setpoint genuinely has to move, and then the divider should be one percent parts placed next to the FB pin rather than at the far end of the rail.

A 6 V maximum input means this part cannot see a 12 V rail, and a 5 V rail at plus ten percent is 5.5 V, which leaves 0.5 V of headroom for transients. The input capacitor should be rated for the rail it sits on rather than for the converter's limit, because the converter clamp is not a transient suppressor.

The power-good output is open drain, so it needs a pull-up to the rail it supervises. A host input with an internal pull-up reads a floating line as good, and the sequencing logic then releases the next rail before this one is in regulation. That is the failure which appears only on the slowest power-up in a batch, and it is why the pull-up belongs in the bill of materials rather than in the host configuration.

Where this order code fits

The usual fit is a single-cell or 5 V rail feeding a 1.8 V or 3.3 V processor, memory or radio supply at 1 A to 3 A in a wearable, a handset or a battery instrument where standby current and board area both matter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the output stay in regulation at 1 mA? Yes, in power save mode the part reduces its switching frequency and holds the output with 17 microamp of quiescent current. The ripple at that load is larger than in PWM, which matters if the load is an analog reference rather than a digital core.

Can I use it for a 0.9 V core rail? Yes on the adjustable version, with the divider set from the internal reference and one percent resistors. The 0.8 V floor is the specification limit, so 0.9 V has margin while anything below 0.8 V is outside the part.

What happens if the inductor saturates? The high-side current limit acts on the switch current, and a saturated inductor makes the current rise faster than the loop can respond, so the output collapses before the limit saves the part. The inductor saturation rating has to exceed the peak current at the highest input voltage.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.