Contact Us

TPS62067QDSGRQ1

Brand: Texas Instruments
Texas Instruments TPS62067QDSGRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62067QDSGRQ1 — Power Management & Signal Chain | Superb Automation

TPS62067QDSGRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62067QDSGRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62067QDSGRQ1: a 2 A automotive step-down converter that switches at 3 MHz in a 2 mm by 2 mm package and holds 18 uA of quiescent current with a power good output

TPS62067QDSGRQ1 is a synchronous converter with both FETs on the die, a fixed 3 MHz loop that allows a 1 uH inductor and a 10 uF output capacitor, a power save mode that keeps efficiency at a milliamp of load, and a power good flag that tells a controller the rail is up in a WSON body of 8 pins. The DSG body is eight pins on a 2.00 mm by 2.00 mm pad with a 0.80 mm height, and the part exists because a camera module or an instrument cluster has room for one small inductor and nothing else.

Order code and package

Catalogue stringTPS62067QDSGRQ1, where 67 marks the member with a power good output, Q1 is the automotive qualifier and DSG is the eight pin WSON
BodyWSON, DSG, eight pins, 2.00 mm by 2.00 mm by 0.80 mm, with a thermal pad that must be soldered to the plane
Reel3000 pieces on a large tape and reel on the QDSGRQ1 row
Finish and moistureNIPDAU plating, level 2 at 260 C, one year of floor life once the bag is opened
Temperatureminus 40 to 125 C junction, AEC-Q100 grade 1, with the maximum on resistance values quoted at 85 C
MarkingSIP on the automotive member, against SJF on the TPS62065-Q1 and 1RF on the forced PWM member
DocumentSLVSCM3B, January 2015, revised August 2023
StatusActive and in production on the addendum dated November 2025

Electrical parameters that decide the application

Input range2.9 V to 6 V, so a 5 V rail, a 3.3 V rail and a single lithium cell all feed it directly
Outputadjustable from 0.6 V up against a 600 mV reference, with 1.5 per cent of accuracy in forced PWM over the full temperature range
Current2 A continuous, with a forward current limit of 2.75 A to 3.3 A on the high side and low side path
Switching frequency2.6 to 3.4 MHz fixed, which is what allows a 1 uH inductor and a 10 uF output capacitor
Quiescent current18 uA typical in power save mode with no load, which is the number that matters on a module that sleeps on a battery
Shutdown0.1 uA typical and 5 uA maximum with the enable low, plus an internal discharge of 200 Ohm across the output
On resistance120 mOhm typical and 180 mOhm maximum on the high side at 3.6 V in, against 75 and 100 mOhm on the low side
Lockout1.73 to 1.83 V falling and 1.90 to 1.99 V rising, with a separate internal 1.8 V reference rail
Power goodan open drain output that asserts above 93 to 98 per cent of the reference and releases between 87 and 92 per cent falling, with a 5 us delay
Start up500 us from an active enable to 95 per cent of the output, with no external soft start capacitor
Thermal shutdown150 C with 10 C of hysteresis, and 64.78 C per watt junction to ambient on a soldered pad
Light loadpower save mode with voltage positioning, where the reference is raised to about 1.01 times nominal so the output does not have to recover from a droop on every wake

Which member of the family belongs on the rail

TPS62067QDSGRQ12 A with a power good output and power save mode, marking SIP, this page
TPS62067AQDSGRQ1the same die forced into fixed frequency PWM at all loads, marking 1RF, for a rail that cannot tolerate the ripple of a power save mode
TPS62065QDSGRQ1the member without a power good output, marking SJF, 3000 pieces on the same reel size
The catalogue versionsTPS62065 and TPS62067 without the automotive qualifier, in the same body, for a board that does not need AEC-Q100
The recommended successorTPS628502-Q1 in a SOT583 body, which the data sheet names on its first page as the newer option for a new board
A converter with a lower currenta 1 A member of the same family shares the pin out and the 3 MHz loop, so a rail that only needs an amp can drop down without a new board arrangement

Points to check before this part goes on a BOM

The 3 MHz loop is the reason the part fits a camera module. At 3 MHz a 1 uH inductor carries about 0.7 A of ripple at 5 V in and 1.2 V out, and a 10 uF ceramic output capacitor holds the ripple under 10 mV. Drop to 1 MHz and the same ripple needs a 3.3 uH inductor and 22 uF, which is three times the board area. The price of the high frequency is switching loss: at 5 V in the high side turns on and off 3 million times a second and the gate charge alone is a few tens of milliwatts, which is why the efficiency curve peaks at 1 A rather than at 2 A.

Power save mode is a system decision as much as an efficiency one. At a milliamp of load the converter skips cycles and the output ripple rises to tens of millivolts, and the voltage positioning feature raises the reference by about 1 per cent so a wake from sleep does not start from a droop. A rail that feeds an analog block or a radio cannot accept that ripple, and the TPS62067A-Q1 member runs fixed frequency PWM at all loads instead. The two are the same die with a different option and the order code is the only thing that separates them, so a bill of materials that swaps one for the other changes the noise floor of the board.

The current limit is a peak comparator and it is set at 2.75 to 3.3 A on a 2 A part. That is a deliberate margin so a 2 A load plus the ripple does not trip, and it means the part will deliver more than 2 A for a short time before it limits. In a fault the limit holds the current at 3 A while the output collapses, the low side FET dissipates the difference, and thermal shutdown arrives at 150 C. In a 2 mm by 2 mm body that is a second or two at 5 V of input, not a millisecond, and a load that fails short should have its own protection.

The lockout sits at 1.73 to 1.99 V, far below the 2.9 V input floor, because it watches an internal 1.8 V rail rather than the input. The practical effect is that a slowly rising input lets the converter start before the input is inside its specified range, and a 2.9 V floor that is treated as a lockout is not one. A module fed from a battery that is deeply discharged will start converting at 2 V and pull the cell down further, which is why a board with a lithium cell needs its own cut off above 2.9 V.

The 5 uA maximum shutdown current is the figure to use in a budget rather than the 0.1 uA typical. On a module that is off for a month the difference between 0.1 uA and 5 uA is 3.6 mAh, which is small against a 2000 mAh cell and not small against a coin cell. The internal discharge of 200 Ohm also draws current from the output whenever the enable is low, so a rail that is held up by another source while this converter is disabled sees a 200 Ohm load to ground through the converter.

The order code carries three things at once and each one is a separate row on the addendum. The 67 marks the power good output, the Q1 marks the automotive qualification, and the DSG marks the body. The catalogue version without the Q1 is the same die and a different row, and the forced PWM member is a different order code again. A purchase order that writes the base part number and expects the automotive row gets the catalogue row, which is a sourcing error that shows up in an audit rather than on the bench.

Working out the inductor and the capacitor

At 3 MHz the ripple current is the input voltage minus the output voltage, times the output voltage, divided by the input voltage, the inductance and the frequency. With 5 V in, 1.2 V out and 1 uH that is 0.76 A, which is 38 per cent of a 2 A load and inside the usual 30 to 40 per cent target. With 3.3 V in the same inductor gives 0.51 A, and the efficiency at light load improves because the ripple loss falls.

The output capacitor is chosen from the ripple and the transient, not from the loop. A 10 uF ceramic has about 3 mOhm of ESR at 3 MHz and the capacitive ripple dominates, so 0.76 A of ripple into 10 uF at 3 MHz gives about 4 mV. The transient is the harder case: a 1 A load step in 1 us has to be supplied by the capacitor until the loop responds, and 10 uF with 30 mV of droop gives about 0.3 us of hold up.

What the power good output can and cannot drive

PG is an open drain output that pulls low when the feedback is between 87 and 92 per cent of the reference on the way down, and it needs an external pull up to a rail that is present before the output. A pull up to the output itself leaves the flag floating during start up, so a supervisor reading it sees an undefined state at exactly the moment it matters. A pull up to a rail that is always on is the correct arrangement, and the sink current is limited to a milliamp or so.

The 5 us delay is short by supervisor standards and a controller that samples the flag every millisecond can miss a fast dip. The flag is a status output and not a protection path, so a rail that must not glitch needs a supervisor with its own comparator rather than this output.

Where this order code fits

This is the 5 V to 1.2 V or 3.3 V to 1.8 V stage in a camera module, an instrument cluster, an advanced driver assistance processor supply, an infotainment head unit or a body control module, where the rail has to hold 2 A in a 2 mm by 2 mm footprint and draw almost nothing when the module sleeps Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

What is the difference between the 67 and the 67A? The 67 has power save mode and a power good output, and the 67A runs fixed frequency PWM at all loads. Same die, different option, and the order code is the only difference.

Does it need an external soft start? No. Start up is internally fixed at about 500 us from an active enable to 95 per cent of the output.

Is the current limit 2 A? No. The forward limit is 2.75 A to 3.3 A on a 2 A rating, so the part delivers its rated current plus ripple without tripping and holds about 3 A into a fault.

Will it run from a single lithium cell? The input range is 2.9 V to 6 V, so a cell that stays above 3 V is fine. The lockout releases at 1.73 to 1.99 V, well below the operating floor, so an external cut off is needed on a deeply discharged cell.

Why is the on resistance quoted at 85 C? Because the maximum values are quoted at 85 C junction, which is where a 2 mm package sits in a hot enclosure, and the 25 C numbers are about 40 per cent lower.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.