TPS61252DSGR
Product Specifications
TPS61252DSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61252DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61252DSGR: 2.3 V to 6 V boost converter with a programmable input current limit
TPS61252DSGR is a synchronous boost converter whose input current limit is set by one resistor, built for battery rails that must not be overloaded in a WSON body of 8 pins. It lifts a single cell or a three cell battery to 5 V while holding the current it draws from the battery inside a limit the source can supply.
Order code and package
| Order code | TPS61252DSGR, DSG package, 3000 pieces on a large reel |
| Body | WSON, 2.00 mm by 2.00 mm, eight pins with a thermal pad, 0.5 mm pitch |
| Current limit | 100 mA to 1500 mA set by one resistor on the ILIM pin, 20 per cent accuracy at 500 mA |
| Feedback | 1.2 V reference, so the output divider sets any voltage up to 6.5 V |
| Mode | 100 per cent duty cycle when the input is above the output, load disconnect in shutdown |
| Protection | Input over voltage at 6.4 V, short circuit, thermal shutdown at 140 C with 20 C of hysteresis |
Electrical parameters that decide the application
| Input range | 2.3 V to 6 V operating, the under voltage lockout falls at 2.0 V |
| Output | Adjustable up to 6.5 V, but the 6.4 V input over voltage protection limits the useful ceiling |
| Switch | High side 200 mOhm, low side 130 mOhm, 1.5 A valley current limit |
| Switching frequency | 3.25 MHz typical, which is why the inductor is about 1 uH |
| Quiescent current | 30 uA while not switching, 0.85 uA to 3.5 uA in shutdown, 3.5 uA of reverse leakage |
| Efficiency | Up to 92 per cent, at 3.6 V in to 5 V out and a few hundred milliamps |
| Soft start | Internal ramp into the output, with the current limit active throughout |
| Power good | 92.5 to 97.5 per cent rising, 87.5 to 92.5 per cent falling, 10 us of delay |
| Thermal | 80.2 C/W junction to ambient in the 2 mm by 2 mm body |
| Control | 1.0 V enable threshold, 0.4 V low, 0.5 uA of leakage on the enable and power good pins |
Family variants and how they differ
| TPS610xx family | boost converters with a switch current limit instead of an input current limit, for a load rather than a source constraint |
| TPS61165 | a boost for an LED string, with a current loop instead of a voltage loop |
| TPS63070 | a buck boost that also covers the case where the input crosses the output, at a higher current |
| TPS62130 | a step down part for the rail the boost is feeding from, not a substitute |
| TPS562212 | a step down part with a similar body size, for the opposite conversion |
Points to check before this part goes on a BOM
The limit is on the input current, not the output, and that distinction decides the usable load. At 3 V in and 5 V out with 90 per cent efficiency, a 1 A input limit gives about 0.54 A at the output. An engineer who reads 1.5 A and expects 1.5 A at 5 V will build a board that current limits at a third of the expected load, and the fix is arithmetic rather than a different part.
The accuracy of the limit is 20 per cent at 500 mA over the full temperature range, so a 500 mA setting can draw 600 mA. On a USB port that is specified at 500 mA this matters, and on a battery it matters less because the limit is protecting a cell rather than a host. The setting has to be chosen against the worst case high, not the typical, whenever the source has a hard limit.
Above the output voltage the part runs at 100 per cent duty and simply passes the input through with the two switch resistances in the path, which is not the same as a buck converter. The output follows the input minus the drop, the loop is out of regulation, and the input over voltage protection at 6.4 V still applies. A rail that swings above and below 5 V needs a buck boost, not this part plus a bypass.
The 3.25 MHz switching frequency is what makes a 1 uH inductor and a 2 mm by 2 mm body practical, and it is also what makes the physical arrangement of the input capacitor, the inductor and the switch node part of the electrical specification. At that frequency a few millimetres of trace is a significant fraction of a period, and a board that works on the bench with flying leads can fail inside an enclosure.
The feedback reference is 1.2 V, which is high for a modern part and is deliberate: it keeps the divider current meaningful against the 30 uA quiescent budget. A 5 V output needs a ratio of 3.17 to 1, and a divider drawing 10 uA adds 10 uA to the standing current, a third of the quiescent figure. The divider is a real term in the power budget on a battery node, not an afterthought.
Reverse current protection and load disconnect are the two features that make this part a battery part. In shutdown the output is disconnected from the input, so the load does not drain the cell through the body diode, and while running the part blocks current flowing back from the output to the input. Both matter when the output holds a large capacitor and the input is a cell that can be removed.
The 2.0 V under voltage lockout with 100 mV of hysteresis sits just above the end point of two alkaline cells in series, which is exactly the case the part is built for and also the case where the last of the capacity is used. A product that needs the last few per cent of a two cell pack has to check the load transient at 2.1 V, because a sag below the falling threshold shuts the part down and the recovery is a full restart.
Power good at 95 per cent rising and 90 per cent falling with 10 us of delay is fast enough to be a sequencing signal but not a supervisor. It reports that the output is close to its set point, not that the input is healthy, so a system that needs to know the battery is low has to watch the input separately. The pin is open drain and needs a pull-up that the quiescent budget can afford.
The input over voltage protection at 6.4 V is close to the 6.5 V output ceiling, and the two together define the real operating envelope. A 5 V output is comfortable, a 6 V output has 400 mV of margin to the protection, and a 6.5 V output has none. Any board that pushes the output toward the top of the range is relying on the input never rising, which is fine only if the input is regulated.
Where this order code fits
It belongs in a hand held instrument, a portable audio product, a battery powered sensor or a USB host supply, where a single lithium cell or three alkaline cells have to make 5 V and the source cannot deliver more than a set current. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
How much output current at 5 V from a 3 V battery? About 0.54 A with a 1 A input limit at 90 per cent efficiency. The limit is on the input, so the output current falls as the input voltage falls.
What happens when the battery is above 5 V? The part runs at 100 per cent duty and passes the input through minus the switch drop. It does not regulate down, so a rail that crosses 5 V needs a buck boost.
Does the output drain the battery when the part is off? No. Load disconnect in shutdown blocks the path, and the reverse leakage is 3.5 uA. That is the difference between this part and a plain boost diode.
How accurate is the current limit? 20 per cent at 500 mA over temperature, so a 500 mA setting can draw 600 mA. Choose the setting against the worst case high when the source has a hard limit.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.