Contact Us

TPS61230DRCR

Brand: Texas Instruments
Texas Instruments TPS61230DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61230DRCR — Power Management & Signal Chain | Superb Automation

TPS61230DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61230DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61230DRCR a 2 MHz boost with a 5 A switch and an adjustable output

The TPS61230DRCR is a synchronous boost converter in a 10 pin VSON body measuring 3 mm by 3 mm and 0.9 mm high, with a 2.3 V to 5.5 V input, an adjustable 2.5 V to 5.5 V output, an integrated 5 A switch and up to 2.1 A of output current at 5 V from a 3.3 V input. It is the adjustable member of the TPS6123x family, alongside the fixed 5 V TPS61232 and the discharge equipped TPS61231.

The converter runs at a quasi-constant 2 MHz in pulse width modulation at moderate and heavy load, and drops into a pulse frequency mode at light load to keep the quiescent draw low. The 2 MHz frequency is what allows a 1 microhenry inductor and small ceramics, and it puts the switching component above the AM band, which helps on a product with a radio.

Control is quasi-constant on-time valley current mode with internal compensation, so there is no external network to size. A supply voltage supervisor with an adjustable threshold and hysteresis is included, and the load is completely disconnected from the input in shutdown.

Key parameters from the SLVSAQ2C document

Input range2.3 V to 5.5 V, one lithium cell or a 3.3 V rail
OutputAdjustable 2.5 V to 5.5 V on this member, fixed 5.0 V on the TPS61232
Output current2.1 A at 5 V from a 3.3 V input, set by the 5 A switch
Switching frequencyQuasi-constant 2 MHz in pulse width modulation, pulse frequency mode at light load
EfficiencyUp to 96 per cent, with a 93 per cent figure quoted for the 3.5 MHz class in the same document family
Switch5 A integrated, with a valley current limit around 4 A
Precharge550 mA current limit after enable, then the output ramps to regulation
SupervisionInput supply voltage supervisor with adjustable threshold and hysteresis
Package10 pin VSON, 3 mm by 3 mm by 0.9 mm, DRC body, 3000 pieces on a large reel, moisture level 1

Five amps of switch at 2 MHz

The 5 A switch rating is a peak device rating, not an output current. At 3.3 V in and 5 V out the input current is about 1.6 times the output current, so 2.1 A out means 3.4 A in plus half the ripple, which is where the 5 A switch sits relative to the load. At 2.3 V in the ratio is 2.4 and the output current falls to roughly 1.4 A before the valley limit is reached.

The precharge behaviour explains a measurement that surprises people. When the part is enabled into a discharged output bank it charges with a 550 mA limit until the output approaches regulation, and then the loop takes over. On a scope that looks like a two slope ramp, and a board that expects a smooth soft start will see a step at the handover.

The 2 MHz frequency makes the placement of the switch node the dominant board concern, even though this body is only 3 mm square. The trace from SW to the inductor has to be short and wide, and the output capacitor has to return to the same ground point as the input capacitor, or the ringing will show up on the output as a common mode step.

Where this part fits

Portable products that need a 5 V rail from a single cell, USB accessories, and any board where a 2.1 A boost has to fit in 3 mm by 3 mm. Our desk keeps the boost cross reference and the second source notes for the 2 MHz class, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The DRC body is 10 pins on 3 mm by 3 mm and the three family members share it, so the order code is the only field that separates the adjustable version from the fixed 5 V version. A fixed part in place of the adjustable one will regulate at 5 V regardless of the divider, which looks like a divider fault on the bench.

The output discharge function belongs to the TPS61231, which the document marks as a preview product. A board that relies on the rail collapsing quickly after disable has to use that member, and if it is not available, an external resistor is the fallback. See component lead time solutions when the specific member is short and incoming inspection plan for the receipt check.

Questions that come up on this part

Can the output be set to 3.3 V from a 2.5 V input, is a common question. It can, and the current available falls with the ratio, so the practical limit at that operating point is about 1 A. The second question is whether the part can pass through the input when the input is above the set output. It cannot in a controlled way on this member, so a product that needs pass through behaviour has to add a bypass path.

The third question is about the supervisor threshold. It is adjustable with an external divider, and the hysteresis is set by a second resistor rather than being fixed, which gives a clean release after a brownout but also means a wrong divider produces a rail that oscillates between run and shutdown.