Contact Us

TPS56C230RJER

Brand: Texas Instruments
Texas Instruments TPS56C230RJER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS56C230RJER — Power Management & Signal Chain | Superb Automation

TPS56C230RJER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS56C230RJER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS56C230RJER: 4.5 V to 18 V, 12 A synchronous buck in a 20 pin HotRod QFN

TPS56C230RJER is a twelve amp buck with D-CAP3 control, a 5 V bias regulator and a mode pin that sets light load behaviour from a resistor divider in a VQFN-HR body of 20 pins. It is the 18 V member of the twelve amp family, pin compatible with its 8 A sibling, and it carries a soft start pin that can be stretched with one capacitor.

Order code and package

Order codeTPS56C230RJER, RJE package, 3000 pieces on a large reel, level 2 moisture sensitivity
BodyVQFN-HR, 3.0 mm by 3.0 mm, 20 pins with a thermal pad
ControlD-CAP3 adaptive on time, internally compensated, ceramic output capacitors
Mode pinEco-mode or forced continuous selected by a resistor divider from VCC
Reference600 mV, 594 mV to 606 mV at 25 C and 591 mV to 609 mV over the full range
Output range0.6 V to 5.5 V, set by two resistors

Electrical parameters that decide the application

Input range4.5 V to 18 V operating, 20 V absolute maximum on VIN
Output current12 A continuous, valley current limit 14 A to 16 A at 25 C and 13 A to 17.5 A over the range
High side switch17 mOhm typical at 25 C
Low side switch5.9 mOhm typical at 25 C
Switching frequency500 kHz nominal, fixed
Minimum on time60 ns, and 180 ns of minimum off time
Bias regulatorVCC 5 V, 4.85 V to 5.15 V, current limit 20 mA
Quiescent current400 uA while not switching, 2 uA in shutdown, 350 Ohm output discharge
Soft start1.2 ms internal with the SS pin open, extended by a capacitor
ProtectionCycle by cycle valley limit, over and under voltage, thermal shutdown, open drain power good

Family variants and how they differ

TPS568230the 8 A part in the same 20 pin footprint, so one board can be rated at 8 A or 12 A
TPS56C21512 A from 17 V in an 18 pin body with 400, 800 and 1200 kHz options and a 4.7 V bias
TPS5622122 A from 18 V in an eight pin body, for a low current rail on the same board
TPS5632013 A in a six pin SOT-23, an order of magnitude less current in a leaded body
TPS621303 A from 17 V in a QFN with DCS control, a different loop for a lighter load

Points to check before this part goes on a BOM

The minimum on time is 60 ns at a fixed 500 kHz, which is 3 per cent duty. An 18 V input therefore cannot regulate below 0.54 V, so the 0.6 V setting is only just inside the window, and any drop in frequency or rise in input pushes the part into minimum on time with a higher ripple. A 12 V input gives 5 per cent duty at 0.6 V and comfortable operation, which is why most boards use this part on a 12 V rail rather than the top of its range.

The mode pin is set by a resistor divider from VCC to ground, not by a logic level, and the divider is read at start-up. That means the light load behaviour is fixed by two resistors on the board and cannot be changed by firmware, and a divider that is slightly out of range selects a mode nobody intended rather than failing loudly.

The current limit is a valley limit of 14 A minimum at 25 C, falling to 13 A minimum over the full temperature range. With a 12 A load the margin is 1 A, and the valley sits half a ripple below the average, so a peak to peak ripple of 2 A puts the valley at 11 A and leaves room, while a ripple of 4 A puts it at 10 A and leaves more. The risk runs the other way: a board with almost no ripple, a large inductor at light load, has the valley equal to the average and trips at 13 A.

The two switches have very different jobs. At 12 V to 1 V the low side conducts about 92 per cent of the period at 5.9 mOhm, which is 0.77 W at 12 A, and the high side about 8 per cent at 17 mOhm, which is 0.24 W. A watt in a 3 mm by 3 mm body is the whole thermal story of the board, and it is why the pad, the vias and the copper pour are part of the specification rather than an afterthought.

Pin compatibility with the 8 A part running in the same body means a board can be built once and populated two ways. Because the current limit, the soft start default and the mode divider are shared, the difference between an 8 A and a 12 A build is the part number and the thermal copper, not the surrounding circuit, and that is worth knowing when a second source or a cost down is being discussed.

The soft start pin is the only way to lengthen the 1.2 ms default. A capacitor on SS gives a longer ramp, which is how inrush into a large output bank is kept under the current limit, and the same capacitor is what a sequencer has to account for when it waits for power good. A build that changes the capacitor late in a programme changes the timing of everything downstream.

The 5 V bias regulator has a 20 mA limit, which is enough for the gate drive of this part but not enough to run anything else. It can be loaded externally for small housekeeping loads, and because the under voltage lockout watches the bias rail, an external 5 V source can hold the part alive when the main input is below 4.5 V. That is a useful trick on a board with a always on 5 V standby rail.

Power good is an open drain output with about 1 ms of start-up delay and thresholds at 85 to 90 per cent on the way up and 110 to 115 per cent before it releases. That window is wide compared with a dedicated supervisor, so a sequencer that needs a tight rail valid signal should use a supervisor rather than this pin, and a fault that pulls the rail to 95 per cent will not be reported at all.

The part is rated to 125 C junction, not 150 C, so a 105 C ambient board has 20 C of headroom for the watt the package sheds. The output discharge function pulls the rail down through 350 Ohm when the enable pin goes low, which is fast for a small capacitor and slow for a 1000 uF bank, and a board that expects a quick collapse after shutdown has to check that number against its own capacitance.

Where this order code fits

It belongs on a 12 V intermediate bus in a switch, a base station, an industrial PC or a set top box, where one rail between 0.6 V and 5.5 V carries up to 12 A and the board is built with a ground plane and a via field under the package. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What sets the light load mode? A resistor divider from the 5 V bias pin to ground, read once at start-up. It is not a logic pin and cannot be changed while the part is running.

Can the board be re-rated to 8 A? Yes, the 8 A TPS568230 shares the 20 pin footprint and the surrounding circuit, so the same board can carry either part with a matching copper area.

How much ripple does the current limit allow? The valley limit is 13 A minimum over temperature against a 12 A load, so the ripple has to keep the valley below that. A 2 A peak to peak ripple puts the valley at 11 A and leaves 2 A of margin.

Is the 0.6 V output safe at 18 V in? It is 3.3 per cent duty against a 3 per cent minimum on time, so the loop runs at the edge. A 12 V input or a lower output range part is the better fit for 0.6 V.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.