Contact Us

TPS563219ADDFR

Brand: Texas Instruments
Texas Instruments TPS563219ADDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563219ADDFR — Power Management & Signal Chain | Superb Automation

TPS563219ADDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563219ADDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563219ADDFR: a 4.5 V to 17 V, 3 A synchronous buck in the eight pin SOT-23-THIN

TPS563219ADDFR is a 3 A synchronous step down converter with D-CAP2 control in a SOT-23-THIN (DDF) body of 8 pins. The DDF body is 1.60 mm by 2.90 mm with eight pins on a 0.65 mm pitch, and the R suffix is the 3000 piece large reel carrying the marking 3219A. The same die also ships as the 2 A TPS562219A in the identical footprint, so a board laid out for one accepts the other and only the current limit and the FET resistances change.

Order code and package

TPS563219ADDFRSOT-23-THIN (DDF), 8 pins, 3000 piece large reel, marking 3219A, -40 to 85 C, NIPDAU finish, MSL level 1 at 260 C, unlimited floor life
TPS563219ADDFTsame body on a 250 piece small reel, marking 3219A, same MSL row
TPS563219ADDFR.A / .Baddendum rows for the same R string; the .B row prints 250 pieces on a small reel, so the reel size has to be confirmed on the offer rather than read from the suffix
TPS562219ADDFRthe 2 A member of the family in the same eight pin body, 133 mOhm and 80 mOhm FETs against 68 mOhm and 39 mOhm on the 3 A part
TPS563219ADDFRG4G4 carried in the string, same DDF body and same 3000 piece reel
Status and documentationActive, production; SLVSDT2 dated November 2016, single revision, no errata sheet attached

Electrical parameters that decide the application

Input range4.5 V to 17 V operating, 19 V absolute maximum on VIN and EN, 25 V on VBST, 27.5 V for a 10 ns transient
Output range0.76 V to 7 V set by the feedback divider, with the internal reference at 765 mV
Feedback accuracy757 mV to 773 mV at 25 C and 751 mV to 779 mV from -40 to 85 C, which is the 1 percent band the front page quotes
Power FETs68 mOhm high side and 39 mOhm low side at VBST minus SW equal to 5.5 V, measured at 25 C
Valley current limit3.5 A minimum, 4.2 A typical and 5.3 A maximum with a 1.5 uH inductor and a 1.05 V output; the 2 A sibling trips at 2.5 A, 3.2 A and 4.3 A
Switching frequency650 kHz fixed, no resistor and no external clock input, so the inductor and the output ripple follow from the part rather than from a setting
Quiescent current650 uA typical and 900 uA maximum non-switching with EN high and VFB held at 0.8 V; 3 uA typical and 10 uA maximum in shutdown
Undervoltage lockout3.45 V minimum, 3.75 V typical and 4.05 V maximum, which sits only 450 mV under the 4.5 V operating floor
Soft start4.2 uA to 7.8 uA of charge current into the SS capacitor, 6 uA typical, so a 10 nF capacitor gives about 1.3 ms of ramp
Power goodOpen drain, good at 90 percent of the reference rising and fault at 85 percent falling, 1 mA sink at 0.5 V
ProtectionCycle by cycle valley limit, 125 percent overvoltage comparator, 65 percent undervoltage hiccup, thermal shutdown at 155 C with 35 C of hysteresis
Enable1.6 V high threshold and 0.6 V low threshold with an internal 450 kOhm resistor to ground, typically between 225 kOhm and 900 kOhm

Family variants and how they differ

TPS562219Athe 2 A member, same pins, same 650 kHz, higher FET resistance and a lower limit window, so dropping to it costs efficiency and headroom
The A suffixthe family is published as TPS56x219A; the plain 219 string belongs to an earlier release and is not the row this document describes
Fixed frequencythere is no synchronisable or spread spectrum option in this family, so a system that needs to move the switching band has to change part
Enable behaviourthe internal pull down holds the converter off until the pin is pulled up, which is why an open EN pin is off and not on
No external compensationD-CAP2 closes the loop internally, so the output capacitor value and ESR are the only loop components a user controls

Points to check before this part goes on a BOM

The current limit is a valley limit, not a peak limit, and the difference matters at 3 A. The comparator watches the low side FET while it conducts, so the DC current at which the part trips sits below the peak inductor current by half the ripple. With the document's own test conditions, a 1.5 uH inductor and a 1.05 V output, the typical trip point is 4.2 A. A converter asked for 3 A with 30 percent ripple therefore runs its valley about 0.45 A under the typical trip, which is the margin the 4.2 A figure buys.

Thermal headroom is set by the low side FET and the copper under the package. At 3 A through 39 mOhm the low side dissipates about 0.35 W before switching loss, and the document quotes a junction to ambient resistance of 87 C/W for the 3 A body on a two layer test board. That is 30 C of rise from the FET alone at 3 A, before the high side switch adds its share, so a small SOT-23-THIN pad on an inner layer with no thermal vias will run the junction far hotter than a pad tied to a ground plane.

The 4.5 V input floor and the 3.75 V typical lockout leave 750 mV of room, which is enough for a 5 V rail at plus or minus 5 percent but not for a 5 V rail that sags to 4.5 V at the connector during a load step. The lockout is monitored on the internal regulator rather than on VIN directly, so the part drops out of regulation before the input reaches 4.05 V, and a board that runs at the floor will restart under a heavy transient instead of riding through it.

Because the switching frequency is fixed at 650 kHz and there is no external compensation, the only two things a user chooses are the inductor and the output capacitor. The document's own application examples use 1.5 uH to 2.2 uH with ceramic output capacitors, and the internal ramp is what allows a low ESR capacitor without a compensation network. Moving to a much larger inductance lowers the ripple and raises the DC current at which the valley limit trips, but it also slows the loop, so the transient response the family is sold on depends on staying near those values.

How the two amps of headroom are really spent

The 4.2 A typical limit is not 4.2 A of usable load. Ripple, tolerance and the minimum of 3.5 A all sit under it, and the family's own 2 A member shows the same pattern with a 3.2 A typical trip. A 3 A load is therefore the rating, and a 3 A continuous load on a 17 V input is the case that needs the thermal work described above.

Startup is the other place the headroom matters. The soft start charges the SS pin with 6 uA, and the converter follows that ramp, so the input current during startup is set by the output capacitor and the ramp time rather than by the current limit. A large output capacitor with a small SS capacitor will hit the valley limit and hiccup before the output reaches regulation.

What the part does when the output is already charged

Startup into a pre-biased output is supported, and the document states that the converter neither discharges the output nor sinks current through the low side FET before the reference is reached. That matters on rails that are back fed from a second supply or from a supercapacitor, where a conventional synchronous buck pulls the pre-charge down through the low side switch.

The overvoltage comparator at 125 percent of the reference is not a latch; the part stops switching and resumes when the output falls back, so a transient that pushes the rail up does not require a power cycle.

Where this order code fits

It powers the internal rails of set top boxes, digital televisions, Blu-ray players, home gateways and any 12 V board that needs 3 A at a low voltage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the 2 A part replace the 3 A part on the same board? Yes on the footprint, since both are the same eight pin DDF body and the same pin out. No on the thermal and current budget, because the 2 A member carries 133 mOhm and 80 mOhm FETs and trips at 3.2 A typical instead of 4.2 A, so a 3 A load that was already close to the limit will hiccup.

Does this part need a compensation network? No. D-CAP2 closes the loop inside the device and the internal ramp stands in for the output ripple, so the user supplies the inductor and the output capacitor only.

What sets the minimum input voltage in a real system? The 3.75 V typical lockout plus the drop across the high side FET at the load current. A 5 V rail that holds 4.75 V at the pin will run, a rail that sags to 4.5 V will sit on the lockout window.

Is the reel size readable from the suffix? Usually R is 3000 pieces and T is 250, and that holds for this part, but the addendum also prints a 250 piece row for a string ending in R, so a purchase order should state the quantity rather than trust the letter.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.