Contact Us

TPS55330RTER

Brand: Texas Instruments
Texas Instruments TPS55330RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS55330RTER — Power Management & Signal Chain | Superb Automation

TPS55330RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS55330RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS55330RTER: 2.9 V to 16 V input boost, SEPIC and flyback converter with a 5.25 A switch

TPS55330RTER is a current-mode boost converter with an integrated switch that also covers SEPIC and isolated flyback topologies in a QFN-16 body of 16 pins. It switches an internal FET rated at a 5.25 A minimum current limit, runs from 2.9 V up to 16 V, sets its frequency anywhere from 100 kHz to 1.2 MHz, and regulates against a 1.254 V reference.

Order code and package

Ordering stringTPS55330RTER, RTE package, 3 mm by 3 mm QFN, tape and reel
Package16-pin QFN with PowerPAD, 3.00 mm by 3.00 mm
Junction range-40 C to 150 C, which is a junction figure and not an ambient one
TopologiesBoost, SEPIC and isolated flyback from the same pinout
Pin count checkVIN, SW, FB, COMP, FREQ, SS, EN, SYNC, GND and AGND plus the pad

Electrical parameters that decide the application

Input range2.9 V to 16 V recommended, lockout falling at 2.7 V
Switch current limit5.25 A minimum, 7.75 A maximum, measured at maximum duty
Switching frequency100 kHz to 1.2 MHz set by a resistor, or locked to an external clock
Reference1.204 V minimum, 1.254 V maximum at 25 C
Soft startProgrammed by a capacitor on the SS pin
SynchronizationAn external clock can drive the switching frequency

Points to check before this part goes on a BOM

The switch limit has a 2.5 A spread between the minimum and maximum columns, and every current calculation has to use the 5.25 A number. A 12 V to 24 V converter delivering 1 A is 24 W out, which at 90 percent efficiency is 2.22 A in and comfortable; the same 24 W from a 5 V rail is 5.3 A in and sits on the minimum limit before any ripple is added, so the input voltage and not the output power decides whether this part fits.

Duty cycle in boost mode is set by the ratio of output to input, so 12 V to 24 V is 50 percent and 5 V to 24 V is 79 percent. At the top of the range the switch conducts for four fifths of the period, the conduction loss scales with that share, and the available output current falls away faster than a linear reading of the input current suggests.

The reference window of 1.204 V to 1.254 V is plus or minus two percent, which on a 24 V output is plus or minus 0.48 V before the divider tolerance is added. A load that needs 24 V within one percent cannot get there with one percent resistors and this reference, and the usual answer is a trimmer or a monitored divider rather than tighter resistors alone.

The recommended input range starts at 2.9 V and the lockout falls at 2.7 V, so a single lithium cell at its 3.0 V end of discharge has 100 mV of margin at best, and a cell that sags under load drops through the floor while it still holds charge. The rising threshold sits above the falling one by the hysteresis in the table, so a converter that starts at 2.9 V will not restart after a load step that pulls the cell to 2.6 V, and the restart then needs the cell to recover or the load to come off.

The 150 C figure is a junction rating, and the 3 mm by 3 mm QFN passes its heat through the pad. At 24 W out with 90 percent efficiency the part dissipates 2.7 W, and even at a good board resistance that is a rise of tens of degrees, so a 70 C ambient is a working limit in a sealed box rather than the 150 C on the front page.

Frequency is a trade rather than a preference: 1.2 MHz allows a small inductor and keeps the ripple current low but adds switching loss, and 100 kHz swings a large inductor with the same ripple and much lower switching loss. The compensation network around COMP changes with the choice, so a board that moves from one end of the range to the other needs the COMP values rechecked, not only the inductor.

In a SEPIC arrangement the coupling capacitor carries the full switch current and holds the input voltage plus the output voltage across it, so its ripple current rating and its voltage rating matter more than its capacitance value. A part chosen only for microfarads runs hot and loses capacitance long before the converter reaches its own thermal limit, and the symptom is a rail that regulates when cold and sags when warm.

Where this order code fits

The usual fit is a 5 V, 12 V or single-cell input that has to produce 12 V, 24 V or a higher rail for a display, a sensor bias or an isolated gate drive supply, where the current is in the hundreds of milliamps and the input can be well below the output. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can this run as a SEPIC for a battery input that crosses the output? Yes, the same part covers SEPIC, with a coupling capacitor and a second inductor. The switch current limit still applies to the input side, so the usable output current is lower than in boost mode at the same input voltage.

What sets the maximum output voltage? The switch voltage rating and the output capacitor rating, not the reference. The 1.254 V reference only sets the divider ratio, so the practical ceiling comes from the 16 V input family rating and the parts around it.

Does the current limit protect the inductor? It protects the switch. The inductor saturation current has to be above the 7.75 A maximum limit, because the part can deliver that much before it acts, and an inductor rated at 5.5 A will saturate before the limit is reached.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.