Contact Us

TPS552872RYQR

Brand: Texas Instruments
Texas Instruments TPS552872RYQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS552872RYQR — Power Management & Signal Chain | Superb Automation

TPS552872RYQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS552872RYQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS552872RYQR 36 V input, 4 A buck-boost in a 3 mm by 5 mm package

The TPS552872RYQR is a four switch synchronous buck-boost converter: 3.0 V to 36 V input, 0.8 V to 22 V output, with the four FETs integrated in a 3 mm by 5 mm HotRod QFN. Because it regulates through both a step down and a step up region, the output stays in regulation while the input crosses it, which is the behaviour a battery powered product needs when a 3 cell pack falls from 12.6 V to 9 V across its discharge.

Power delivery is quoted at two operating points rather than as a single current: 30 W from a 12 V input and 25 W from a 9 V input, with a 4 A average inductor current limit setting the ceiling. Peak efficiency in the document is 96.7 per cent at 12 V to 20 V and 1.5 A, and 98.3 per cent at 12 V to 12 V and 2 A, which is the pass-through region where a buck-boost is at its best.

Control is average current mode, switching from 200 kHz to 2.2 MHz set by a resistor, with optional clock synchronization and optional spread spectrum. The output current monitor is 5 per cent accurate, and the output voltage compensation is adjustable so that a cable drop between the converter and the load is cancelled at the load rather than at the pin.

Key parameters from the SLVSHG1 document

Input range3.0 V to 36 V, covering a 12 V adapter and a 3 cell battery with the transient allowance
Output range0.8 V to 22 V programmable, with 1 per cent reference accuracy
Power delivery30 W from 12 V input and 25 W from 9 V input, with a 4 A average inductor current limit
Efficiency96.7 per cent at 12 V to 20 V and 1.5 A, 98.3 per cent at 12 V to 12 V and 2 A
Switching frequency200 kHz to 2.2 MHz by resistor, with external clock sync and optional spread spectrum
Current monitoring5 per cent accurate output current monitor, plus adjustable cable droop compensation
Light loadProgrammable PFM and FPWM modes
ProtectionOutput overvoltage, average and cycle by cycle current limit, short circuit hiccup, thermal shutdown
Package3.0 mm by 5.0 mm HotRod QFN, leadless, RYQ body

What the pass-through region buys

In a 12 V to 12 V application the converter is neither stepping up nor stepping down, and a four switch buck-boost can hold the output with the high side of one leg and the low side of the other conducting, which is why the efficiency figure reaches 98.3 per cent. For a USB PD product that has to deliver 12 V from a 12 V adapter, that region is where the product spends most of its life, and a buck-only topology cannot get there at all below 12 V.

The 30 W and 25 W figures are the honest way to quote a buck-boost. A single current rating hides the fact that the inductor current in boost mode is higher than the output current, so the same part delivers more watts at 12 V input than at 9 V. Any quote that states only an output current for a buck-boost is telling half the story.

EMI, spread spectrum and the 2.2 MHz ceiling

Optional spread spectrum moves the switching energy across a band instead of parking it on one harmonic, which is how a 400 kHz converter passes a conducted emissions limit that a fixed frequency version would fail. The cost is a small increase in output ripple and a slightly wider inductor tolerance band. On a product with a radio inside, the other lever is external clock sync, which lets the converter run from a clock the radio knows about and keeps the beat note out of the receive band.

The 2.2 MHz ceiling is what allows a small inductor and a small output bank. It also raises switching loss, so a 36 V input at 2.2 MHz has to be checked against the thermal derating curve before the inductor is fixed.

Where this part fits

Battery powered instruments, USB PD sources that have to work from a drained pack, 12 V rails that must hold up during a car crank, and any rail that has to survive an input that crosses the output. Our desk keeps the cross reference and the second source notes for this class of part, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

Confirm the RYQ body, because the 3 by 5 mm HotRod package is shared across the family and a reel for the 8 A member looks identical on the outside. Confirm the inductor saturation rating against the 4 A average limit plus ripple, since the limit is on inductor current, not on output current. Then confirm whether the board needs spread spectrum, because that setting is a strap and a board built without it cannot be moved by software.

See date code management for how we segregate the family on receipt, and incoming inspection plan for the marking check on a leadless body.

Questions that come up on this part

Is 4 A the output current, is the first question. No, it is the average inductor current limit, and the output current in boost mode is lower than that. The second question is whether the part can run from a 3.3 V rail. It can, at the bottom of the 3.0 V to 36 V window, but the boost ratio and the inductor current have to be checked at that point because the input current is high for a given output power.