Contact Us

TPS54KC23RZRR

Brand: Texas Instruments
Texas Instruments TPS54KC23RZRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54KC23RZRR — Power Management & Signal Chain | Superb Automation

TPS54KC23RZRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54KC23RZRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54KC23RZRR 30 A D-CAP4 buck in a 16 pin WQFN-HR

The TPS54KC23RZRR is a 4 V to 16 V, 30 A synchronous buck in a 16 pin WQFN-HR, with 5.8 milliohm high side and 2.3 milliohm low side FETs. The control loop is D-CAP4, the fourth generation of the adaptive on time scheme, and its selling point is a low minimum on time: the part can regulate a 1 V rail from a 16 V input at 1.4 MHz without skipping pulses, which is the case where earlier generations ran out of headroom.

Three switching frequencies are selectable, 800 kHz, 1.1 MHz and 1.4 MHz, and the part supports all ceramic output capacitors with no external compensation. The reference is 0.5 per cent over 40 to 125 degrees junction, and the output range runs from the reference value to 5.5 V. Sense is a differential remote pair, so the loop regulates at the load pins rather than at the nearest capacitor.

The package is the point of the part as much as the control loop. Sixteen pins in a WQFN-HR with the pad doing the thermal work, pin compatible with the 25 A TPS54KB2x, so a board can move between 25 A and 30 A without a revision. Settings are programmed through the MSEL pin, current limit is set by a resistor on RILIM, and the fault set covers valley overcurrent, overvoltage, undervoltage and PGOOD.

Key parameters from the SLVSHH9 document

Input range4 V to 16 V, with an optional 3.1 V to 5.3 V external VCC bias
Output current30 A continuous with 5.8 milliohm high side and 2.3 milliohm low side FETs
Output voltageReference value up to 5.5 V, differential remote sense
Switching frequency800 kHz, 1.1 MHz or 1.4 MHz, selected by the MSEL pin
Reference accuracy0.5 per cent over 40 to 125 degrees junction
Current limitProgrammable with a resistor on RILIM, valley overcurrent protection
ModesAuto skip Eco mode for light load, forced continuous conduction for tight ripple
Package16 pin WQFN-HR, pin compatible with the 25 A TPS54KB2x

Minimum on time and the high step down ratio

A 12 V to 1 V conversion at 1.4 MHz has an on time of about 60 ns. A control scheme with a 100 ns minimum on time cannot get there, so it either drops the frequency, skips pulses at the bottom of the ripple, or gives up regulation at the top of the input range. D-CAP4's low minimum on time is what makes 1.4 MHz usable at that ratio, and that is why the part is aimed at data centre boards where the inductor has to be small and the input is 12 V.

The trade is switching loss. At 1.4 MHz the high side FET switches more often, and 5.8 milliohm at 30 A is not the dominant term at light load. Boards that idle most of the time should consider 800 kHz and a larger inductor instead of 1.4 MHz and a small one; the part supports both, and the MSEL pin makes the choice a build option.

Valley current limit and load steps

Valley overcurrent protection watches the low side current at the end of the off time, which is the point where the inductor current is lowest. That is the right place to detect a saturated inductor, because the valley rises fast once the core saturates. The RILIM resistor sets the threshold, and the value has to be chosen against the inductor's saturation rating rather than against the load current, or a fast load step will trip a limit that the magnetics could actually survive.

Overvoltage and undervoltage protection are both provided, with PGOOD as an open drain output. Because the part has no bus, the fault response is fixed by pin and cannot be changed in the field, which is what a medical or industrial qualification process usually prefers.

Where this part fits

Space constrained data centre boards, 12 V to core rails at 30 A, and any board that has to move between 25 A and 30 A on the same footprint. Our desk keeps the family cross reference for this class of part, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The RZR suffix is the 16 pin WQFN-HR, and it is physically smaller than the 21 pin and 40 pin bodies used by the neighbouring devices, so a footprint check matters. Confirm the MSEL strap against the intended frequency, and confirm the RILIM value against the inductor saturation current. Then confirm the external VCC bias arrangement: with a 3.1 V to 5.3 V bias the part holds 30 A over the full input range, and without it the low end of the input window narrows.

See incoming inspection plan for how we check a 16 pin body with a short marking code, and one stop BOM sourcing for the rail group.

Questions that come up on this part

Does D-CAP4 need any external compensation, is the usual question. No, and the part is stable across the recommended ceramic output range. The second question is whether 1.4 MHz is usable at 16 V input and 0.6 V output. It is, but the on time is near the minimum, so the input voltage should be checked against the on time curve before the frequency is fixed in the bill.