TPS54622RHLR
Product Specifications
TPS54622RHLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54622RHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54622RHLR: 6 A synchronous step-down converter with a 0.6 V reference and hiccup current limit
TPS54622RHLR is the member of the 6 A 17 V buck family that drops the reference to 0.6 V for lower output rails and adds a hiccup restart on a hard fault in a VQFN body of 14 pins. The TPS54622 shares the body, the pin out and the 26 mOhm high side and 19 mOhm low side switches of the TPS54620, but its reference is 0.6 V instead of 0.8 V, so a 1 V rail needs a divider ratio of 1.67 rather than 2.33 and the same board can reach lower outputs. The current limit behaviour also differs: on a sustained overload the part enters hiccup, waits 16384 switching cycles and tries again, which keeps a shorted rail from running hot. Input range is 4.5 V to 17 V and the switching frequency spans 200 kHz to 1.6 MHz.
Order code and package
| Order code | TPS54622RHLR |
| Input voltage, VIN | 4.5 V to 17 V |
| Power stage input, PVIN | 1.6 V to 17 V |
| Rated output current | 6 A |
| Integrated switches | high side 26 mOhm, low side 19 mOhm |
| Voltage reference | 0.6 V, plus or minus 1 percent over temperature |
| Fault behaviour | hiccup current limit with a 16384 cycle restart delay |
| Switching frequency | 200 kHz to 1.6 MHz, set by an RT resistor |
| Synchronisation | external clock through the RT/CLK pin |
| Shutdown current | 2 uA typical |
| Package | 14 pin VQFN, 3.5 mm by 3.5 mm, exposed pad |
| Document | SLVSA70F, March 2011, revised October 2017 |
Electrical parameters that decide the application
| High-side current limit | 8 A minimum, 11 A typical, 14 A maximum |
| Low-side sourcing limit | 6.5 A minimum, 10 A typical, 15 A maximum |
| Low-side sinking limit | 2 A minimum, 3 A typical, 4 A maximum |
| Hiccup restart | 16384 switching cycles after the fault |
| Thermal shutdown | 160 C rising, 175 C maximum, 10 C hysteresis |
| Reference | 0.6 V nominal, one percent over the junction range |
| Input UVLO | 4 V rising minimum, 4.5 V maximum, 150 mV hysteresis |
| Non-switching supply current | 600 uA typical, 800 uA maximum |
| Thermal resistance | 40.1 C per W junction to ambient, 32 C per W with a via array |
| Junction range | -40 C to 150 C |
| Soft-start charge current | 2.3 uA |
| Power good thresholds | 92 percent falling fault, 106 percent rising good, at the sense pin |
Points to check before this part goes on a BOM
The 0.6 V reference changes the divider, not the converter. A 0.9 V output needs a top resistor of 1 kOhm and a bottom of 2 kOhm, which puts more of the output noise onto the sense pin than a 0.8 V reference would. On rails below 1 V the sense trace has to be short and taken from the point of load, otherwise the divider picks up switching noise that the error amplifier cannot reject.
Hiccup is the practical difference between this part and its sibling. On a hard short the current limit trips, the part shuts down, waits 16384 cycles and retries, so the average dissipation during the fault is a small fraction of the steady state loss. A latch off part would need a supervisor to restart, and a part that keeps current limiting would heat until the thermal shutdown at 160 C cycled it anyway.
The lower reference also means the soft-start ramp acts on a smaller voltage. The SS/TR pin charges at 2.3 uA and the tracking window is 20 mV to 60 mV of mismatch to the sense pin, so a soft-start capacitor chosen for a 0.8 V part ramps this one faster in absolute terms. Boards that need a fixed ramp time should size the capacitor against 0.6 V, not against the older figure.
Current limit maximums are wider on this part than on the sibling: 14 A on the high side against 11 A. For a board that must not deliver more than 8 A into a fault, the inductor saturation current and the downstream wiring have to be rated for the maximum column, not the typical one, because the part is allowed to reach it before it limits.
Thermal figures improve when the pad is stitched. The document gives 40.1 C per W on a standard board and 32 C per W with a four by four array of 0.010 inch vias under the body, which is a quarter less rise at the same loss. On a 6 A rail at 1 V out the loss is around 1 W, so that difference is 8 C of junction temperature at the same ambient.
The power good window is narrower than on the 0.8 V part: 92 percent on the falling fault and 106 percent on the rising good. A sequencer that uses PWRGD to enable a load therefore waits until the rail is within 6 percent of nominal, which is the right behaviour for a 0.9 V core but leaves little room for a rail that sags under a transient at start up.
Both members of the family share the body and the pin out, so a board can be built for either and the grade chosen at the BOM level. The two are not interchangeable in one socket without firmware change, because the divider ratio and the current limit behaviour differ, and the reference voltage is the field that shows up first when a substitution is attempted.
Where this order code fits
This order code fits core and DDR rails below 1.2 V on networking, storage and industrial boards where a short on the load must not turn into a burned converter, and where the 0.6 V reference allows a 0.75 V or 0.9 V output from the same divider that a 0.8 V part could not reach. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is this part a drop in for the TPS54620? The body and pin out match, but the reference is 0.6 V instead of 0.8 V, so the feedback divider has to be recalculated, and the fault behaviour changes from current limit to hiccup.
Does hiccup restart on its own? Yes, after 16384 switching cycles. At 500 kHz that is about 33 ms between attempts.
What is the lowest output this part can regulate? The reference is the floor, so 0.6 V plus the divider headroom. In practice the minimum on time and the ripple set the usable floor well above that.
SUPERB quotes this order code against the exact suffix with packing and date codes, and the BOM Shortage Recovery page sets out what has to match before a 6 A socket takes a part from a different line.