Contact Us

TPS54395PWPR

Brand: Texas Instruments
Texas Instruments TPS54395PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54395PWPR — Power Management & Signal Chain | Superb Automation

TPS54395PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54395PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54395PWPR: a dual 3 A synchronous step down converter in a 16 pin HTSSOP, supplied in a 90 piece tube

TPS54395PWPR is a dual channel adaptive on-time step down converter with both switches integrated and no external loop compensation in a HTSSOP (PWP) body of 16 pins. It takes 4.5 V to 18 V in and runs two independent 3 A rails from one package, each with a 90 milliohm high side and 60 milliohm low side switch and a 700 kHz pseudo-fixed frequency set by the input and output voltage rather than by a resistor. The feedback threshold is 765 mV, the loop is internal and stable with ceramic output capacitors, and the part enters a light load mode on its own so a standby rail does not burn the full switching loss. Each channel has its own current limit at 4.7 A typical, its own enable pin and its own soft start capacitor.

Order code and package

TPS54395PWPRHTSSOP body of 16 pins with a PowerPAD, 90 pieces in a tube rather than a reel, nickel palladium finish, moisture level 2 at 260 C with one year of floor life, marking PS54395, active status in the addendum dated 10 August 2026
TPS54395RSAR and RSATthe same die in a 16 pin QFN body measuring 4.25 mm by 4.25 mm, 3000 pieces on a large reel for the R suffix and 250 pieces on a small reel for the T suffix
R suffix on this parton most converters R means a large reel, but on the PWPR string the quantity column reads 90 and the carrier reads tube, so the suffix is not the packing on this order code
Temperature rangeminus 40 C to 85 C on the published rows, which is narrower than the 125 C that the same family is often assumed to carry
Channelstwo independent switchers with separate feedback, separate enable, separate soft start and separate current limit, sharing only the input rail and the ground
Padthe PowerPAD is the ground return and the heat path, and the vias under it are what keep a 3 A rail from folding back on a hot board

Electrical parameters that decide the application

Input voltage4.5 V to 18 V, which covers a 5 V, 12 V or 15 V bus with no pre-regulator
Output voltage0.76 V to 7.0 V per channel, set by a divider against the 765 mV feedback threshold
Output current3 A per channel, with both channels able to run at the same time inside the package dissipation
Switch resistance90 milliohm high side and 60 milliohm low side, which is what makes the low duty cycle rails efficient
Feedback threshold758 mV minimum, 765 mV typical and 773 mV maximum at 25 C, with a temperature coefficient of plus or minus 115 parts per million per degree
Switching frequency700 kHz pseudo-fixed, set by the input and output voltage through the adaptive on-time loop rather than by an external resistor
Current limit3.5 A minimum, 4.7 A typical and 6.5 A maximum per channel with a 2.2 microhenry inductor, measured across the low side switch rather than with a sense resistor
Current limit stabilitythe low side resistance is compensated over temperature at 4000 parts per million per degree, which is what keeps the limit from drifting with the die temperature
Minimum off time220 ns, which sets the maximum duty cycle and therefore the lowest input voltage that can hold a given output
Soft startset by a capacitor on each channel, charging at about 8 microamp, so the ramp is a capacitor choice rather than a fixed value
Undervoltage protectionthe output undervoltage comparator trips at 68 per cent of the reference with a 1.5 ms delay, and the part enters hiccup after the delay
Enable thresholds2.0 V to enable and 0.4 V to disable, with 225 kilohm to 900 kilohm of input resistance on the pin
Supply lockoutthe internal 5 V regulator has to reach 3.83 V before the part starts, with 0.6 V of hysteresis on the way down
Thermal shutdown155 C on the rising edge, which is the last protection rather than an operating point

Package and quantity rows of this converter

TPS54395PWPRthe dual 3 A converter covered by this order code, 16 pin HTSSOP with a PowerPAD, supplied 90 pieces in a tube
TPS54395RSARthe same die in a 16 pin QFN measuring 4.25 mm by 4.25 mm, 3000 pieces on a large reel, which is the volume string
TPS54395RSATthe QFN body on a 250 piece small reel, which is what a pilot build uses
Frequency700 kHz pseudo-fixed from the adaptive on-time loop, with no resistor and no synchronisation pin
Loopinternal, stable with ceramic output capacitors, so the rail does not need the ESR that older converters relied on
Channelsindependent feedback, enable, soft start and current limit, sharing only the input rail and the ground
Temperatureminus 40 C to 85 C on the published rows, which is narrower than the junction rating and is the figure a sealed box has to be checked against

Points to check before this part goes on a BOM

Two 3 A channels in one body is a thermal statement. The switches are 90 and 60 milliohm, and at 12 V to 1.2 V the low side carries most of the current for most of the period. Both channels at full load inside a 16 pin HTSSOP need the pad copper and the airflow that the thermal tables assume.

The frequency is not adjustable. The 700 kHz figure comes from the adaptive on-time loop and the input and output voltages, so a board cannot move it to avoid an emissions band. A board that needs a different frequency needs a different part.

Current limit is measured across the low side switch. There is no sense resistor, which saves a part and a loss, and it also means the limit moves with the die temperature. The 4000 parts per million compensation is what keeps that movement small.

The output undervoltage delay is 1.5 ms. A rail that dips for less than that does not enter hiccup, which is deliberate: a transient load step should not restart the converter. A rail that stays low for longer does.

The 85 C limit is worth checking against the enclosure. The published rows stop at 85 C ambient, and a board inside a sealed box can reach that with the load it has. A rail that needs 105 C has to come from another part in the family rather than from an assumption.

The tube is 90 pieces. A tube is what a hand load line or a repair bench wants, and it is also the reason the PWPR string is not the one a volume line should order. The QFN strings are the reel options.

What a dual converter saves and what it costs

Two rails from one body share the input capacitor, the enable logic and the board area, which is the reason a set top box or a digital television supply is built this way. The cost is that the two channels share a thermal budget and a package, so one channel running hot raises the other.

The channels are independent in every other respect. Separate feedback, separate soft start and separate current limit mean a fault on one rail does not force the other down, which is the behaviour a board with a standby rail and a main rail needs.

Reading the adaptive on-time loop from a board point of view

Because the frequency is set by the voltages rather than by a resistor, the ripple current changes with the input and output ratio. A rail that is quiet on a 12 V bench supply can show a different ripple on a 15 V bus, and the output capacitor is chosen for the worst case of that ratio.

The internal ramp means the loop does not need the ESR of the output capacitor to be stable, so ceramic capacitors are allowed. A board that copies an older converter with an electrolytic output and no ceramic will still work, and it will be larger than it needs to be.

Where this order code fits

a set top box, a digital television supply or a network terminal that needs a main rail and a standby rail from one 12 V bus Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the frequency adjustable? No. The 700 kHz figure comes from the adaptive on-time loop and follows the input and output voltage, so there is no frequency resistor and no synchronisation pin on this part.

How much current can both channels carry at once? 3 A each electrically, with the package dissipation deciding how much of that is available at the ambient inside the enclosure. Both channels at full load need the pad copper the thermal tables assume.

Why is this order code supplied in a tube? The PWPR row is 90 pieces in a tube, which is what a hand load line or a repair bench uses. The QFN strings carry the 3000 piece reel and the 250 piece small reel.

What is the current limit and how accurate is it? 4.7 A typical per channel with a 3.5 A minimum and a 6.5 A maximum, measured across the low side switch and compensated over temperature.

Does a short on one output affect the other? Not directly. Each channel has its own current limit and its own hiccup timer, so a shorted rail restarts on its own while the other keeps regulating.

What temperature does the published table cover? Minus 40 C to 85 C on the rows in the addendum, which is narrower than the 125 C junction that the silicon is rated for and the figure a sealed enclosure has to be checked against.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.