Contact Us

TPS54361QDPRRQ1

Brand: Texas Instruments
Texas Instruments TPS54361QDPRRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54361QDPRRQ1 — Power Management & Signal Chain | Superb Automation

TPS54361QDPRRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54361QDPRRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54361QDPRRQ1 60 V automotive buck that survives a 65 V load dump

The TPS54361QDPRRQ1 is a 60 V, 3.5 A step down converter with the high side switch integrated, qualified to AEC-Q100 grade 1 for operation from minus 40 to plus 125 degrees ambient. The headline number is not the 60 V input but the load dump survival: the device is specified to ride through 65 V pulses per ISO 7637, which is the event that kills a converter chosen only on its steady state input rating. The high side FET is 87 milliohm, and the switching frequency is set between 100 kHz and 2.5 MHz by a resistor on RT or by an external clock.

This is the part that turns a 12 V automotive bus, or a 24 V truck bus, into a 5 V or 3.3 V rail for body electronics, instrument clusters and sensor modules. The quiescent current of 152 microamp with the output in regulation and the pulse skipping Eco-mode are what keep a module inside its key off current budget, and the 2 microamp shutdown current is what stops a parked vehicle from draining through a converter that was supposed to be off.

Current mode control keeps the compensation external and simple, so the same power stage can be retuned for a different output capacitor without changing the controller. The undervoltage lockout is internally set at 4.3 V and can be raised with a divider on the enable pin, which is how a module is made to stay off during a cold crank until the battery recovers.

Key parameters from the SLVSCC4B document

Input range4.5 V to 60 V operating, with survival of 65 V load dump pulses per ISO 7637
Output current3.5 A continuous from an integrated 87 milliohm high side switch
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees ambient, HBM class H1C and CDM class C3B
Switching frequency100 kHz to 2.5 MHz with RT, 160 kHz to 2.3 MHz with an external clock, and 200 k on RT giving 450 kHz minimum, 500 kHz typical and 550 kHz maximum
Reference0.8 V, 0.792 V to 0.808 V over the full temperature range
Current limit4.5 A minimum, 5.5 A typical and 6.8 A maximum, measured open loop at the SW pin so the figure does not depend on the inductor
Quiescent current152 microamp operating, 2.25 to 4.5 microamp in shutdown with EN low
Orderable bodyWSON DPR, 10 pins, 3000 pieces on a large reel, 330 mm carrier

What the current limit figure actually protects

The current limit is specified open loop at the SW pin, which means the 4.5 A to 6.8 A window describes the switch and not the inductor current. In a real circuit the inductor and the slope compensation shape the peak, so a board that sits close to 3.5 A with a small inductor sees a higher peak than one with a large inductor at the same average. The 60 ns current limit threshold delay is short enough that the peak overshoot in a hard short stays inside the switch rating.

Hiccup behaviour follows a persistent fault: the converter stops, waits, and retries, so a shorted load produces a ticking output rather than a hot FET. That is the behaviour an automotive body module needs, because a harness short that clears itself should not require a service visit.

Thermal behaviour in a 10 pin body

A 3.5 A converter in a 10 pin WSON relies on the exposed pad and on the copper under it. At 12 V to 5 V and 3 A the conduction loss in the 87 milliohm switch is around 0.45 W at a 42 per cent duty, and the switching loss adds to that at 500 kHz. The pad has to be stitched to an inner ground plane with several vias, and the thermal path is the first thing to check when a module passes on the bench and drops out in a hot soak.

The minimum on time of 100 ns at 23.7 V input and 5 V output sets the highest usable frequency at high line for a given output. At 60 V input the same 100 ns becomes 6 per cent of a 500 kHz period and the converter can still regulate 3.3 V, but a board pushed to 2.2 MHz at 48 V input runs out of on time before running out of inductor.

Where this part fits

Automotive body controllers, cluster supplies, camera modules and sensor nodes all need a rail that survives the electrical environment rather than one that merely tolerates it. The same part serves industrial equipment running from a 48 V bus, telecom line cards with a 48 V feed, and test equipment where the input comes from an unregulated adapter. Sequencing is handled by the SS pin, which doubles as a tracking input, so a rail can be made to follow the 3.3 V rail instead of starting on its own schedule.

On the supply side the question is usually authenticity and reel integrity rather than the part number, because an automotive grade converter that has been re-marked or re-reeled is worse than no part at all. Our sourcing desk works from date code management for that reason, and the wider view is in power management cross reference.

What to check before a purchase order

The first field is the Q1 suffix together with the temperature grade, since the same document covers parts that stop at 125 degrees junction. The second is the package letter, DPR being the 10 pin WSON in this case. The third is the reel size, where the published R row carries 3000 pieces on a 330 mm carrier, and a small reel has to be sourced as a separate row.

Our desk checks those three against the customer bill of materials and quotes the automotive grade string with its grade, rather than a generic 60 V converter that happens to fit the footprint. See obsolete part cross reference hub when the grade is no longer stocked, and component lead time solutions when it is stocked but allocated.