Contact Us

TPS54240QDGQRQ1

Brand: Texas Instruments
Texas Instruments TPS54240QDGQRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54240QDGQRQ1 — Power Management & Signal Chain | Superb Automation

TPS54240QDGQRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54240QDGQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54240QDGQRQ1: 2.5 A step-down converter with a 42 V input and a 200 mOhm high-side switch

TPS54240QDGQRQ1 is a 42 V input buck converter with an integrated high-side switch, a 138 uA quiescent current and a programmable frequency up to 2.5 MHz in a MSOP body of 10 pins. The TPS54240 takes 3.5 V to 42 V in and delivers 2.5 A through a 200 mOhm high-side switch with an external catch diode. Current mode control keeps the compensation simple, pulse skipping reduces the no load supply current to 138 uA, and the enable pin takes the shutdown current to 1.3 uA. The switching frequency is set by a resistor and the part also accepts an external clock. The reference is 0.8 V, the current limit threshold is 6.1 A typical, and the body is a 10 pin MSOP with a PowerPAD.

Order code and package

Order codeTPS54240QDGQRQ1
Input voltage3.5 V to 42 V
Output current2.5 A
High-side switch200 mOhm typical, 410 mOhm maximum at 12 V in
Reference0.8 V, 0.792 V to 0.808 V
Switching frequencyset by an RT resistor, 450 kHz to 720 kHz at 200 kOhm
Current limit3.5 A minimum, 6.1 A typical
Quiescent current138 uA typical, 200 uA maximum
Shutdown current1.3 uA typical, 4 uA maximum
Enable threshold1.15 V to 1.36 V
Package10 pin MSOP with a PowerPAD
Thermal shutdown182 C
DocumentTPS54240 data sheet, automotive qualified

Electrical parameters that decide the application

Internal UVLO2.5 V rising and falling, no hysteresis
Soft-start charge current2 uA
Soft-start to sense matching45 mV at 0.4 V on the soft-start pin
Error amplifier transconductance310 uS
Error amplifier bandwidth2700 kHz
Power good low resistance50 Ohm at 3 mA
Power good leakage10 nA at 25 C
Minimum input for a valid power good0.95 V to 1.5 V
Junction range-40 C to 150 C
Thermal resistance40 C per W junction to ambient in the PowerPAD body
External clocklocks within 100 us at 500 kHz
Catch diodeexternal, rated for the 6.1 A peak and the 42 V input

Points to check before this part goes on a BOM

Forty two volts covers a 24 V rail with margin and a 36 V battery system without one. The 3.5 V minimum input also allows the part to run from a 5 V rail, which makes it usable as a second stage converter where the intermediate bus is already regulated. That flexibility is why the same part appears on very different boards.

Two hundred milliohms on the high side is high for a 2.5 A part, and the loss shows it. At 2.5 A and a 24 V to 5 V conversion the switch conducts for about a fifth of the period, so the conduction loss is around 0.25 W, and the external diode adds roughly 0.4 W. Neither is a problem for the package, but together they set the efficiency ceiling well below a synchronous converter.

The 6.1 A typical current limit against a 2.5 A rating is generous because the part is a non-synchronous converter with a wide input range. The inductor has to be rated above the 3.5 A minimum limit rather than the typical, because the part is allowed to reach the minimum before it limits on a cold day with a low input voltage.

Pulse skipping at light load is what produces the 138 uA figure. The part stops switching when the output is above the regulation point and restarts when it falls, so the average supply current is low but the output ripple becomes a low frequency sawtooth. A board with a sensitive load should add a small preload, which keeps the part in continuous conduction without cost worth mentioning.

The 2.5 V internal UVLO with no hysteresis is a behaviour worth knowing. The part starts switching at 2.5 V and stops at the same level, so a slowly rising input will produce an oscillation at the threshold. In practice the 3.5 V operating minimum and the external UVLO divider, where one is fitted, keep the part away from that region.

Power good on this family is a window comparator on the sense pin, with the low threshold at 50 Ohm to ground when the output is out of range. It is not a precision supervisor, so a sequence that depends on it should allow for the tolerance in the divider and the 10 nA of leakage at the pin.

A 10 pin MSOP with a PowerPAD gives 40 C per W, which is workable at the losses this part produces. The pad has to be soldered, and the copper under it should be connected to the ground plane with vias, otherwise the thermal figure in the document does not apply and the part runs hot at full load on a 24 V input.

Where this order code fits

This order code fits 12 V and 24 V industrial rails that need 2.5 A at 5 V or 3.3 V, automotive body modules on a 12 V bus, and telecom line cards where the intermediate rail is 24 V. The Q1 suffix puts it on the automotive qualification flow. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is the catch diode external? Yes. This is a non-synchronous converter, so the diode is a board component rated for the peak current and the input voltage.

What is the current limit? 3.5 A minimum and 6.1 A typical, sensed in the high-side switch, cycle by cycle.

How is the frequency set? By a resistor on the RT/CLK pin, or by an external clock that the part locks to within about 100 us.

SUPERB quotes this order code with packing and date codes on the offer, and the BOM Shortage Recovery page lists the fields a substitute has to match on a 24 V rail.