TPS53511RGTR
Product Specifications
TPS53511RGTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS53511RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS53511 1.5 A converter for a 4.5 V to 18 V input in a 3 mm body
The TPS53511RGTR is a synchronous step down converter with the switches integrated, in a 16 pin 3 mm by 3 mm QFN. It takes a supply from 4.5 V to 18 V, a conversion input from 2 V to 18 V, and delivers 1.5 A continuously at a fixed 700 kHz. The control loop is D-CAP2 mode, which needs no external compensation and works with all ceramic output capacitors as well as with polymer parts.
This is the smallest member of the family that covers a 12 V rail with a real current rating, and it is the part that fits a rail where a module would be too tall and a controller with external FETs would be too wide. Skip mode at light load keeps the efficiency up when the load drops, and the shutdown current is below 10 microamp.
Key parameters taken from the SLUSBG4B document
| Supply input | 4.5 V to 18 V on VCC, and 2 V to 18 V on the conversion input, so a 12 V rail is inside the window with margin |
| Output current | 1.5 A continuous, with cycle by cycle overcurrent limiting |
| Output voltage | Down to 0.76 V, set by the feedback divider against the internal reference |
| Switching frequency | 700 kHz fixed, which is the same clock as the TPS53127 and keeps the inductor small |
| Control mode | D-CAP2 with no external compensation, and a proprietary circuit that adapts to low ESR and to ceramic output capacitors |
| Light load | Skip mode, which reduces the switching frequency as the load falls |
| Shutdown current | Below 10 microamp, which matters on a rail that has to sit idle for long periods |
| Soft start | Adjustable with a capacitor on SS, and prebiased start supported |
| Bias | An internal regulator with a 5.5 V output on VREG5 and a 1 microfarad bypass capacitor |
| Protection | Cycle by cycle current limit, power good, and overtemperature, with an internal bootstrap switch |
| Package and thermal | 16 pin RGT QFN, 3.00 mm by 3.00 mm, minus 40 to plus 85 degrees ambient, 125 degrees junction |
What 1.5 A buys and what it does not
At 1.5 A the part covers a memory termination, a small FPGA auxiliary rail, an analog front end or a sensor supply. It does not cover a processor core, and the cycle by cycle current limit will fold the output back rather than deliver the load. The useful way to size it is to take the load current at the maximum ambient and check the junction temperature with the thermal resistance of the RGT body on the actual copper area, because a 3 mm package with 1.5 A inside it has a limited heat path.
The 700 kHz clock keeps the inductor small, in the 1 microhenry to 2.2 microhenry range for a 12 V to 1.2 V conversion, and the output capacitor can be all ceramic. That combination is what makes the part usable on a board where the rail has to fit in the shadow of a connector.
Where the TPS53511 belongs on the board
- Point of load rails in computing systems, the application the document lists first
- Distributed non isolated DC to DC converters on a 12 V backplane with several small rails
- Instruments that need a 1.2 V or 1.8 V auxiliary rail with no compensation components
- Boards that need a precharged start on a rail shared with other loads
- Standby rails where the sub 10 microamp shutdown current matters
Order code, package and thermal limits
| TPS53511RGTR | 16 pin RGT QFN, 3.00 mm by 3.00 mm, large reel, active and in production |
| Dissipation | At 1.5 A from 12 V to 1.2 V the part dissipates around 0.4 W, and the pad area sets the junction rise from that figure |
| Absolute maximum | 20 V on VIN, VCC and EN, 6.5 V on the bootstrap, 1.5 A output, 150 degrees junction |
| Bootstrap | Internal switch, so the high side drive needs only the external capacitor between VBST and SW |
Sourcing notes for this line
Small integrated converters are the highest volume part on most boards, so they are also the first to go on allocation. The comparison point is the power management cross reference, which lists the 1.5 A to 2 A converters that share the RGT footprint and the ones that differ in the feedback reference.
Where the exact code is short, a 2 A part in the same body is usually the answer as long as the feedback reference is the same, because the divider then does not change. The pin to pin cross reference page marks which of those parts share the 0.76 V reference and which do not.
For a board that is short of this part in the middle of a build, the second lever is the quantity per board rather than the part itself, and the kitting service page covers how a partial kit is staged to keep the line running.
Questions buyers ask about this part
Can it take a 19 V adapter rail? No. The recommended maximum on VCC is 18 V and the absolute maximum is 20 V, so a 19 V rail sits above the recommended range and needs a different part.
Does it need an external compensation network? No. The D-CAP2 loop is internally compensated, and the external parts are the inductor, the capacitors, the feedback divider and the soft start capacitor.
Is the output stable with ceramic capacitors only? Yes, that is the case the control circuit targets, and it also works with low ESR polymer parts.
What sets the soft start time? A capacitor on the SS pin, with the internal current source charging it. No capacitor gives the fastest ramp the part allows.