Contact Us

TPS53319DQPR

Brand: Texas Instruments
Texas Instruments TPS53319DQPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS53319DQPR — Power Management & Signal Chain | Superb Automation

TPS53319DQPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS53319DQPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS53319 14 A synchronous converter with Eco-mode and a 1 % reference

The TPS53319DQPR is the 14 A member of the TPS5331x family, a synchronous buck converter with both MOSFETs integrated in a 22 pin 5 mm by 6 mm LSON-CLIP package. It runs from a conversion input of 1.5 V to 22 V with a separate 4.5 V to 25 V supply for the control circuitry, produces 0.6 V to 5.5 V, and reaches 91 % efficiency from 12 V to 1.5 V at 14 A according to the document. The 8 A member of the same family is the TPS53318.

Eco-mode is the light load behaviour that gives the family its efficiency curve: the converter reduces its switching frequency as the load falls instead of holding a fixed clock, and the shutdown current is below 110 microamp. D-CAP control with no external compensation keeps the transient response fast without a network to tune, which is the same reason the part appears on boards with a short schedule.

Key parameters taken from the SLUSAY8G document

Conversion input1.5 V to 22 V on the power stage, with a separate VDD from 4.5 V to 25 V for the control and driver circuitry
Output0.6 V to 5.5 V, which covers a core rail and a 5 V housekeeping rail from the same family
Current14 A continuous on the TPS53319, 8 A on the TPS53318, with integrated NexFET switches
Reference0.6 V with 1 % accuracy, so the output tolerance at the load is the reference plus the divider
Efficiency91 % from 12 V to 1.5 V at 14 A, which is the row to quote when a board has a thermal limit rather than a current limit
Switching frequency250 kHz to 1 MHz, selected by a resistor on the RF pin and stored at start up
Light loadAuto skip Eco-mode or PWM only, selectable, so the same part can be quiet or efficient
Soft startInternal voltage servo soft start with 0.7 ms, 1.4 ms, 2.8 ms or 5.6 ms options
Bias railAn internal 5 V LDO on the VREG pin, so the control circuitry runs from the input with no external bias
ProtectionAdjustable overcurrent with thermal compensation, OVP, UVP, UVLO and overtemperature, with an open drain power good
Package22 pin DQP LSON-CLIP, 5.00 mm by 6.00 mm, minus 40 to plus 85 degrees ambient

The separate control supply and the single rail option

VDD and the power stage input are separate pins on this family, which allows a board to run the control circuitry from 5 V while the power stage switches a 1.8 V rail, or to tie them together for a single rail input. The single rail option is what most boards use, because the 4.5 V VDD minimum and the 1.5 V conversion minimum only overlap at a low voltage that no real bus uses, so a 12 V input feeds both pins.

The internal 5 V LDO on the VREG pin is the reason no external bias is needed. It supplies the drivers and the analog circuitry, and it needs its own 1 microfarad bypass capacitor close to the pin. A board that forgets that capacitor sees a converter that starts and then drops out under load, because the driver supply collapses during a switching cycle.

Where the TPS53319 belongs on the board

  • Server and storage rails where a 1.0 V or 1.2 V output at 14 A comes from a 12 V bus
  • Workstations and desktop motherboards, the applications the document lists first
  • Telecom infrastructure boards that need a 3.3 V or 5 V rail at several amps with a small footprint
  • Test equipment where the 91 % efficiency keeps the rail out of the thermal budget of a sealed box
  • Boards that need a precharged start, since the family supports starting into an already charged output

Order code, package and thermal limits

TPS53319DQPR22 pin DQP LSON-CLIP, 5.00 mm by 6.00 mm, large reel, 14 A member
TPS53318DQPRThe 8 A member of the same family, same body and same pinout, lower current rating
Newer alternatesThe document points to the TPS548A28 and TPS548A29, 16 V 15 A converters with remote sense, as the newer parts for data centre rails
Shutdown currentBelow 110 microamp, which is the number that matters for a standby rail on a battery backed system
ThermalThe LSON-CLIP body is the heat spreader, so the thermal pad has to be soldered to copper with vias rather than left on a signal layer

Sourcing notes for this line

This family has been in production since 2012 and has a published successor path, which makes the sourcing conversation easier than for a part with no second source. The comparison table is the power management cross reference, and it lists the 8 A and 14 A members as footprint compatible with each other and the newer 15 A parts as a different footprint.

Where a board is short on the 14 A member, the 8 A member drops into the same footprint and only changes the current ceiling, which is enough for a rail that was over specified. That substitution and its thermal consequences are set out on the pin to pin cross reference page.

Moving to the newer TPS548A28 is a board change rather than a substitution, because the package and the pinout differ. The how to verify a drop in replacement page treats a package change as a new qualification rather than a drop in.

Questions buyers ask about this part

Is the 14 A rating at any input voltage? It is the continuous output current with the thermal path the document assumes. A board with a small copper area or a high ambient reaches the thermal limit before the current limit, which is why the 91 % efficiency figure matters.

Can Eco-mode be turned off? Yes. The mode pin selects auto skip or PWM only, so a board that needs a fixed ripple can hold the clock and accept the efficiency loss.

What does the internal 5 V LDO supply? The drivers and the analog circuitry, which is why there is no external bias rail. It needs a 1 microfarad bypass capacitor at the VREG pin.

Does it start into a precharged output? Yes, the family supports precharged start up, so a rail that is already at 0.5 V is not discharged when the converter enables.