Contact Us

TPS51275B-1RUKR

Brand: Texas Instruments
Texas Instruments TPS51275B-1RUKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51275B-1RUKR — Power Management & Signal Chain | Superb Automation

TPS51275B-1RUKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51275B-1RUKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51275B-1 dual buck controller with 5 V and 3.3 V always on LDOs

The TPS51275B-1RUKR is a dual synchronous step down controller in a 20 pin 3 mm by 3 mm WQFN that also carries two 100 mA low dropout regulators, one at 5 V and one at 3.3 V. The two switching stages produce the main system rails and the two LDOs stay alive in the low power states, which is what a notebook or a tablet needs to keep its standby logic and its memory refreshed while the main converters are off.

The controller runs adaptive on time D-CAP control at either 300 kHz or 355 kHz, with out of audio light load operation that keeps the switching frequency above the audible band when the load is light. A 260 kHz clock output is available to drive an external charge pump for the gate drive of the load switches, so the board does not need a separate oscillator for that function.

Key parameters taken from the SLVSCT3 document

Input range5 V to 24 V on VIN, with 26 V absolute maximum on the VO1 input, so a 19 V adapter with a transient has margin
Outputs5 V and 3.3 V fixed, adjustable by plus or minus 10 % through the feedback dividers
LDOs100 mA at 5 V and 100 mA at 3.3 V, always on in the standby states
Reference1 % accuracy, which is the row that decides the tolerance budget on both rails
Switching frequency300 kHz or 355 kHz selectable, with out of audio operation at light load
Soft startInternal 3.2 ms voltage servo soft start, so no external capacitor sets the ramp
Current sensingLow side RDS(on) sensing with dedicated overcurrent setting terminals for each stage
Clock output260 kHz VCLK for an external charge pump, which is how the load switch gate drive is generated without a second converter
ProtectionOVP, UVP, OCP, non latching UVLO and overtemperature, plus a combined power good signal
Package and thermal20 pin RUK WQFN at 94.1 degrees per watt junction to ambient, minus 40 to plus 85 degrees ambient

Why the LDOs matter more than the switchers on a standby rail

On a battery powered system the two LDOs are what keeps the real time clock, the embedded controller and the memory refresh alive when the main rails are off. They are 100 mA parts, so they are not there to run the system, but they decide whether the platform can come out of standby without a full boot. The always on label means VREG3 and VREG5 stay regulated as long as VIN is present, independent of the enable pins of the two switching stages.

The consequence for a board is the standby current budget. The LDOs are linear, so their current comes straight from VIN, and a 100 mA load at 3.3 V from a 19 V adapter dissipates 1.6 W in the part. Boards that keep a heavy load on the always on rail in standby run hot, and the 94.1 degrees per watt figure leaves no room for that mistake.

Where the TPS51275B-1 belongs on the board

  • Notebook and tablet main power, where 5 V and 3.3 V have to be present in standby
  • Industrial panel computers that take a 12 V or 19 V adapter and need a 5 V housekeeping rail
  • Point of sale terminals and kiosks with a battery backed standby state
  • Telecom customer premises equipment where the 5 V rail feeds the line interface and the 3.3 V rail feeds the logic
  • Test instruments that need a 260 kHz clock for a charge pump without adding an oscillator

Order code, package and thermal limits

TPS51275B-1RUKR20 pin RUK WQFN, 3.00 mm by 3.00 mm, large reel, minus 40 to plus 85 degrees ambient
Skip modeOut of audio on the -1 member of the family, which is the variant for boards that must not sing in standby
Always on LDOsVREG3 and VREG5, both on the -1 member, so a board cannot lose the standby rails by disabling a switcher
Output dischargeBuilt in, so the rails come down in a defined way when the enables drop
EnablesSeparate enable inputs for the two switching stages, so the 3.3 V rail can come up before or after the 5 V rail

Sourcing notes for this line

Dual controllers with always on LDOs are chosen by the standby architecture, not by the switching performance, and a substitute that lacks the always on rails changes the platform behaviour even when the footprint matches. The comparison point is the power management cross reference, which marks which members carry the LDOs and which do not.

Where the RUK code is short, the family has several skip mode variants with the same body, and the difference is in the light load behaviour and the LDO presence. The pin to pin cross reference page sets out which of them can drop into the same footprint and which need the enable logic checked.

For a build that is short on this part, the practical fallback is to split the two stages into two single controllers, which costs board area but keeps the schedule. The BOM shortage recovery page covers that kind of split as one of the standard moves.

Questions buyers ask about this part

Are the LDOs on in shutdown? They stay regulated as long as VIN is present, which is what the always on label means. Only the two switching stages follow their enable pins.

Can the outputs be adjusted above 5 V? Only within the plus or minus 10 % window. A rail that needs 12 V is not this part, and the 5.5 V output limit in the recommended conditions confirms it.

What is the 260 kHz clock for? An external charge pump that generates the gate drive for load switches, so the board does not need a separate switching supply for that rail.

Does it need a bootstrap diode? No. The bootstrap diode is internal, which is one of the reasons the external component count is low on this family.