Contact Us

TPS4H000BQPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS4H000BQPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS4H000BQPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS4H000BQPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS4H000BQPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS4H000BQPWPRQ1: quad 1000 milliohm high side switch for 40 V automotive loads with full diagnostics

TPS4H000BQPWPRQ1 is four high side switches in one package, each with a 1000 milliohm channel and full diagnostics, qualified to AEC-Q100 grade 1 and rated to 40 V on the supply in a HTSSOP body of 20 pins. The TPS4H000-Q1 is a quad channel smart high side switch that runs from 3.4 V to 40 V and switches loads up to 0.5 A per channel with a 1000 milliohm channel resistance. Version A carries an open drain status output and version B carries an analogue current sense output, both with a fault pin, and each channel has thermal shutdown, current limit and open load detection. The body is the 20 pin PWP HTSSOP with an exposed pad.

Order code and package

Order codeTPS4H000BQPWPRQ1
Supply voltage3.4 V to 40 V
Output current per channel0.5 A at the stated current limit
Channel resistance1000 milliohm
Channels4
Version Aopen drain status output per channel
Version Banalogue current sense output
QualificationAEC-Q100 grade 1, -40 C to 125 C ambient
Package20 pin HTSSOP, PWP body, exposed pad
Pin count20
DocumentSLVSD73B, December 2015, revised March 2018

Electrical parameters that decide the application

Supply absolute maximum, under 400 ms45 V
Reverse polarity-36 V
Undervoltage turn on3.5 V to 3.7 V to 4.0 V
Undervoltage shutdown3.0 V to 3.2 V to 3.4 V
Undervoltage hysteresis0.5 V
Operating current7 mA at 13.5 V with 0.1 A per channel
Open load detection threshold1.6 V to 2.6 V
Open load deglitch300 us to 600 us to 800 us
Current limit deglitch80 us to 180 us
Thermal shutdown160 C to 175 C, reset at 155 C
Thermal swing60 C
Thermal resistance38.5 C per W junction to ambient, 1.7 C per W junction to case bottom
Junction range-40 C to 150 C

Points to check before this part goes on a BOM

One ohm per channel sets both the voltage drop and the dissipation. At 0.4 A a channel drops 400 mV, which is 3.3 percent of a 12 V rail and 0.16 W in the switch, and four channels at that current dissipate 0.64 W. With 38.5 C per W that is a 25 C rise, which is comfortable in a 85 C module and marginal at 125 C ambient unless the exposed pad has copper behind it.

Version A and version B are different parts, not options on one die. Version A gives an open drain status pin per channel, which a controller reads as a logic level; version B gives an analogue current sense output on one pin with a channel selected by the SEL pin. The order code has to match the diagnostic scheme the firmware was written for, and the two are not interchangeable on the same board.

The open load threshold of 1.6 V to 2.6 V with a 300 us to 800 us deglitch is how the part detects a load that has gone open while the switch is off. It compares the supply to the output with the channel disabled, so a load that leaks current can mask the fault. The 2.6 V upper threshold is wide enough that a load with a parallel bleed resistor may never be detected as open, which is a decision the harness has to be checked against.

Thermal protection has two thresholds and a swing. Shutdown starts between 160 C and 175 C, reset is at 155 C, and the 60 C swing means a channel that trips will not retry until the die has cooled 60 C or the channel has been cycled. That is deliberate: a load that pulls a sustained overcurrent heats the die, and a small hysteresis would make the switch oscillate in and out of thermal shutdown.

Reverse polarity is rated at -36 V, which covers a jump start or a battery connected backwards for the duration of the fault, but only if the external reverse blocking is present. The part is not a reverse battery protection device on its own, and the -36 V figure is an absolute maximum rather than an operating condition. The 45 V transient rating applies for under 400 ms, which is the load dump window a 12 V automotive bus can present.

The current limit is quoted at 0.5 A in the electrical conditions and the deglitch is 80 us to 180 us, so a short circuit is interrupted in under 200 us rather than in microseconds. That is fast enough for the switch and slow enough to ride through the inrush of a capacitive load. An inductive load that is switched off has to have its energy absorbed somewhere, and the datasheet's absolute maximum ratings for the output pins are the limit that decides whether an external clamp is needed.

Qualification is stated at grade 1, -40 C to 125 C ambient, with HBM class H2 and CDM class C4B. The 150 C junction limit is what the thermal calculation has to respect inside that 125 C ambient, which leaves 25 C of rise for four channels at full load. The junction to case bottom figure of 1.7 C per W shows that the pad does almost all of the work, so the thermal vias and the copper area are part of the component specification rather than an afterthought.

Where this order code fits

This order code suits automotive body and comfort loads: LED strings, camera and sensor sub modules, relays, and general resistive, capacitive or inductive loads that have to be switched from a body controller with diagnostics. AEC-Q100 grade 1 covers -40 C to 125 C ambient, which is what a module under a seat or in a door has to survive. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What is the difference between version A and version B? Version A reports each channel on an open drain status pin. Version B reports an analogue current on one pin with a channel selected by SEL. They are separate order codes.

Can it drive a 1 A load? The stated current limit is 0.5 A and the channel is 1000 milliohm, so a 1 A load is outside the part. Use a lower resistance member of the family.

Is it protected against a reverse connected battery? The output pins are rated to -36 V absolute maximum, which is a survival rating. External reverse blocking is still required in a product.

SUPERB supplies this order code in the PWP tape and reel with date codes, packing and country of origin on the offer, and the Supplier Quality Audit page lists the fields to compare before a switch position is filled from a second line.