Contact Us

TPS48111LQDGXRQ1

Brand: Texas Instruments
Texas Instruments TPS48111LQDGXRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS48111LQDGXRQ1 — Power Management & Signal Chain | Superb Automation

TPS48111LQDGXRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS48111LQDGXRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS48111LQDGXRQ1: an automotive 100 V smart high side driver with a pre-charge path

TPS48111LQDGXRQ1 is an AEC-Q100 grade 1 high side gate driver for external FETs in a VSSOP (DGX) body of 19 pins. The DGX body is a 19 pin VSSOP with one pin removed between adjacent positions for creepage, 5000 pieces on a large reel, and the marking 2UZS. The 48111 in the ordering string is the variant with the separate pre-charge driver, which is the difference that decides whether the part can bring up a large capacitive load.

Order code and package

TPS48111LQDGXRQ1VSSOP (DGX), 19 pins, 5000 piece large reel, marking 2UZS, -40 to 125 C ambient
Finish and floor lifeNIPDAU lead finish, MSL level 2 at 260 C with a one year floor life
QualificationAEC-Q100 grade 1, functional safety capable with documentation available, ±2000 V human body model and ±750 V charged device model on the corner pins
Pin names worth knowingINP drives the main gate, INP_G drives the pre-charge gate, FLT_I flags overcurrent, FLT_T flags overtemperature, IMON is the analog current monitor
Absolute maximum100 V on VS, CS+ and CS-, -30 V on SRC, -1 V to 100 V on the sense pins to ground, 5.5 V on the logic inputs

Electrical parameters that decide the application

Operating range3.5 V to 80 V input with 100 V absolute maximum, covering 12 V, 24 V and 48 V systems
Reverse polarityprotection down to -30 V without an external diode in the return path
Gate drive3.7 A peak source and 4 A peak sink, enough to switch parallel FETs in a high current path
Charge pumpintegrated 12 V pump with 100 uA of capacity, which is what holds the gate above the rail for a high side N-channel device
Shutdown current1.6 uA total at a 48 V input with EN/UVLO low
Short circuit response1.2 microseconds on the TPS48111, against 4 microseconds on the TPS48110 that lacks the pre-charge driver
Current monitorIMON output accurate to 2 percent, used for energy management rather than only for protection
Overcurrent protectiontwo adjustable levels, IWRN for a warning and ISCP for the trip, each with its own response time set by the TMR pin
Fault behaviourauto retry or latch off, chosen by the board rather than fixed in the part
Thermal flagremote overtemperature protection reported on FLT_T, separate from the current flag on FLT_I
ESD±2000 V human body model per AEC Q100-002, ±750 V charged device model on the corner pins and ±500 V on the rest

Family variants and how they differ

TPS48110Q1same 100 V front end without the pre-charge driver, 4 microsecond short circuit response instead of 1.2 microseconds
TPS48111Q1the pre-charge variant, which is the ordering string on this page, for loads that are largely capacitive at switch on
Against a discrete driverone part replaces the charge pump, the gate drive and the current sense amplifier, and adds the two level protection the discrete circuit does not have
Back-to-back FET supportthe device drives external back-to-back N-channel MOSFETs, which is how the reverse polarity rating is realised on the board

Points to check before this part goes on a BOM

The pre-charge path is what separates the two family members, and it exists for one situation: a load with a large input capacitance that would otherwise draw a surge through the main FET at the moment of connection. The G driver with its INP_G input brings the capacitance up through a small series FET first, then the main path closes. Without that sequence the same board trips the overcurrent protection on every hot plug.

The two level overcurrent scheme is the other reason this part is specified rather than a plain gate driver. IWRN gives a warning level with its own response time and ISCP a trip level, both set by resistors, and the TMR pin decides how long the part waits before it acts. That lets a system ride through a motor start and still cut off on a real fault, which a single threshold cannot do.

The 1.6 uA shutdown current is quoted at a 48 V input, which is the state a parked vehicle sits in. A driver that leaks milliamps from a 48 V traction battery through the sense divider will drain it over weeks, so the figure belongs in the standby current budget next to the quiescent current of the controller it feeds.

The ±2 percent current monitor is accurate enough to be used as a measurement rather than only as protection. That changes what the board needs: a system that logs energy can use IMON directly, while a system that only protects can use the same pin as a comparator input and lose nothing. The accuracy claim applies to the monitor, not to the two protection thresholds, which are set by external resistors.

What the 19 pin body tells you

The VSSOP body has one pin removed between adjacent positions, which is a creepage measure rather than a mechanical accident. On a 100 V part, the gap between the high side pins and the logic pins is part of the safety margin, and substituting a different 19 pin body with a continuous pin row loses that margin even though the footprint looks close.

The board consequence of the 5000 piece reel is worth planning for as well. It is a larger carrier than the 3000 piece reels on the converters this driver usually sits beside, so a line that feeds both from one machine needs the feeder set up for two reel sizes rather than one. That is a scheduling item, not an electrical one, but it turns up whenever a first article is built from mixed stock, and it is easier to answer at the quote than on the line, before the feeder plan is fixed, because two reel sizes on one machine is a change to the line and not to the part.

Where this order code fits

It switches 12 V, 24 V and 48 V loads in automotive and industrial systems: power distribution boxes, battery disconnect paths, motor and heater feeds, and any load that has to be brought up softly because it is mostly capacitance. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

What does the 48111 add over the 48110? A separate pre-charge gate driver with its own control input, plus a faster 1.2 microsecond short circuit response. The rest of the front end, the two level overcurrent protection and the current monitor, is the same.

Can the part drive several FETs in parallel? Yes, the 3.7 A source and 4 A sink gate drive is specified for parallel FETs in high current paths. The gate resistors and the routing of the paralleled devices decide how evenly the current shares, so the drive strength is a starting point rather than the whole answer.

Is the current monitor good enough for measurement? It is quoted at 2 percent, so it can be used for energy management and logging as well as for protection. The two protection thresholds are set by external resistors and carry their own tolerance, so they are not covered by that 2 percent figure.

How is a fault reset? Either auto retry or latch off, chosen by how the board is wired rather than by the part. FLT_I reports the current event and FLT_T the overtemperature event, so a controller can tell the two apart before it decides to retry.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.