Contact Us

TPS3840DL24DBVR

Brand: Texas Instruments
Texas Instruments TPS3840DL24DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3840DL24DBVR — Power Management & Signal Chain | Superb Automation

TPS3840DL24DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3840DL24DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3840DL24DBVR nano power supervisor for a 2.4 V threshold with a programmable delay

The TPS3840DL24DBVR watches a rail against a 2.4 V threshold, holds the reset low while the rail is below it, and releases the reset after a delay set by a capacitor on the CT pin. Supply current is 300 nA typical and 700 nA maximum, the supply range runs from 1.5 V to 10 V, and the output is open drain active low, so a pull up resistor is part of the circuit rather than an option.

The family behind this order code is arranged around three output types and a threshold table that runs from 1.6 V to 4.9 V in 0.1 V steps. The DL prefix is the open drain active low member, PL is push pull active low and PH is push pull active high, and all three share the body, the pinout and the timing.

Key parameters taken from the TPS3840 document

Threshold2.4 V nominal on this option, from a table that covers 1.6 V to 4.9 V in 0.1 V steps
Threshold accuracy1 per cent typical and 1.5 per cent maximum over temperature
Hysteresis100 mV for thresholds from 1.6 V to 3.0 V, and 200 mV from 3.1 V up, which is a wide window on purpose for a battery rail
Supply range1.5 V to 10 V directly, and a 24 V rail through an external divider pair
Supply current300 nA typical and 700 nA maximum, both printed rather than only the typical
Start up delay100 to 350 microseconds, 220 microseconds typical, before the reset is released on a supply that has just come up
Programmable delay50 microseconds with the CT pin open, 6.2 milliseconds with 10 nF, 619 milliseconds with 1 microfarad and 6.2 seconds with 10 microfarad
CT pin resistance500 kilohm typical, 350 to 650 kilohm over temperature, which is the number the delay equation uses
Detection speed15 microseconds typical and 30 microseconds maximum from the rail crossing the threshold to the output going low
Glitch immunity10 microseconds at 5 per cent of overdrive, so a shorter spike below the threshold is ignored
Manual resetPin 4, asserted on a logic low, and left floating when unused
Body and reelSOT-23 5 pin DBV, 3000 pieces on a large reel, body marking DL24
Temperature and handlingMinus 40 to plus 125 degrees C, moisture level 1 at 260 degrees with unlimited floor life

The delay arithmetic is the row that catches people out. With no capacitor the delay is 50 microseconds, but the start up delay of 220 microseconds is added on top of it when the supply has just come up, and with a capacitor the programmable delay is added to the start up delay rather than replacing it. A board that needs 300 milliseconds after a rail is good therefore needs the capacitor to be sized against the difference, not against the total.

Where the numbers matter in a real build

The 100 mV of hysteresis on a 2.4 V threshold is 4 per cent of the trip point, which is generous compared with the 11 mV on the family that sits below 2 V. That width is there because a battery rail sags under load and recovers when the load drops, and a supervisor with a narrow window would chatter the reset line on every transmit burst. The cost is that the rail has to come back 100 mV above the threshold before the reset is released, which on a slowly charging battery is a real delay in start up.

The 300 nA typical and 700 nA maximum are both printed, and the maximum is the figure to budget with. A product that sleeps for months has to size its cell around the maximum, and a part whose maximum is more than twice its typical would be a problem at 0.7 microamp if the budget had been taken from the typical figure alone. That is the reason the vendor prints both percentages in the feature list.

The open drain output needs a pull up to a rail that stays alive when the monitored rail collapses. A pull up to the monitored rail itself is the common mistake, because the reset line then goes down with the rail it is supposed to be reporting, and a processor can be held in an undefined state instead of being held in reset. Where the rail that collapses is the only rail on the board, the push pull member is the one to order, because it keeps a defined level without a second supply.

What to check before a purchase order is released

  • The output type letter, since DL, PL and PH share a body and a pinout and differ in polarity and in whether a pull up is needed.
  • The threshold option, because the family prints 1.6 V to 4.9 V in 0.1 V steps and the string carries the chosen value.
  • The CT capacitor value, which sets the delay and is added to the start up delay rather than replacing it.
  • The pull up resistor on the reset net, which has to go to a rail that survives the fault.
  • The 24 V case, where the supply is divided externally and the divider tolerance adds to the 1.5 per cent of the part.

Which projects this part fits

Battery powered equipment, handheld instruments, metering and any product that monitors a rail above 5 V through a divider are the cases the vendor lists. A 2.4 V threshold suits a two cell alkaline pack or a single cell lithium rail that must not be discharged below its safe point, and the 10 V supply range means a 9 V rail can be watched without a divider at all.

Questions that come up before a purchase order is released

Can the delay be zero?

The shortest delay is 50 microseconds with the CT pin open, and the start up delay of about 220 microseconds still applies to a supply that has just come up.

Does the manual reset pin need a pull up?

No. The pin can be left floating when unused, and it is asserted by pulling it low through a switch or an open drain output.

Why is the hysteresis so wide?

Because a battery rail sags under load. The 100 mV window is there to stop the reset line from chattering on every load step, and it has to be accounted for in the release level.

How SUPERB handles this line

Nano power supervisors with a programmable delay are ordered in reels and consumed slowly, so the reel split and the date code are the usual commercial questions. Our power management cross reference covers what a single chip supervisor replaces on a board that currently uses a comparator, a reference and a timer, and the date code note explains what we accept on a reel that has been in storage. Where a customer needs a second source for a qualified board, the pin to pin cross reference is the first check.